Will Hopkins Tailgate EasyLift Fit 1991 Ford F-150 Pickup Truck

Question

Question:

does the hopkins tailgate easy lift fit my 1991 ford f150 4x4 lariat xlt tailgate?

asked by: Michael D

0

Expert Reply:

The Hopkins Tailgate EasyLift, part # 74211 will fit your 1991 Ford F-150 if your truck is not the SuperCrew model.

This assist reduces the weight of a 30 to 40 lb tailgate to 4 to 7 lbs. Drilling is required for installation. I have attached a product review for this tailgate assist you can check out.

expert reply by: Jeffrey L

0

Answer 1

The best product we have for wiring third brake lights in a camper shell is the 3rd Brake Light Logic Module part #PP20-702. If you were to combine this with an in-bed wiring harness such as the Curt 5th Wheel/Gooseneck Custom Wiring Harness part…

view full answer...

Answer 2

The tailgate lift assist #74211 for your 2005 Toyota Tundra is going to be applying some force on the inner part of the tailgate but the force is not so great that it would dent or chip paint from the tailgate. We have not had any complaints about…

view full answer...

Answer 3

I spoke with my contact at Hopkins and he informed me that the issues you described are very rare, and that anytime something like that has occurred they have replaced the damaged part. He said that all of the Hopkins Tailgate Assist, part #74211,…

view full answer...

Answer 4

We do offer a tailgate assist product for a 2006 Toyota Tundra, the Hopkins EasyLift Tailgate Assist, part #74211. DeeZee doesn't offer a tailgate assist for the 2006 Toyota Tundra.

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 7

In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then adapt this to a 7-way so you can hook up a brake controller. I won't have much info for anyone particular dump truck but…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

If the light mounting surface on your older Prowler trailer is not flat enough to allow for use of caulk for sealing the rear of the RV Tail Light #30-92-001 then you might want to use a weather strip tape like #WS1412 which is 1/4-inch thick x…

view full answer...

Will Hopkins Tailgate EasyLift Fit 1991 Ford F-150 Pickup Truck

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching