How To Wire Dome and Third Brake Light On Leer Camper Shell

Question

Question:

Hi i need supplies and instructions to wire up a leer topper inside light with on off switch and third brake light. Thank you

asked by: Neil S

0

Expert Reply:

The best product we have for wiring third brake lights in a camper shell is the 3rd Brake Light Logic Module part # PP20-702. If you were to combine this with an in-bed wiring harness such as the Curt 5th Wheel/Gooseneck Custom Wiring Harness part # C56070 (works on all truck with 7-way) you could pull the signals for the module as well as the power for the light. You'd just simply remove the trailer connector and plug from the end of the harness and wire it directly to the module and light with a switch of your choosing in between like part # PK34212. The yellow wire could be used for the stop and the black for power.

expert reply by: Conner L

0

Answer 1

Yes, you can use the factory trailer connector on your 2015 Nissan Titan to power the third brake light on your Leer camper shell. That said, they don't make a plug and play harness for this so you will need to do some wiring but no splicing into…

view full answer...

Answer 2

To wire in a truck camper shell's third brake light to your 2016 Ford F-150 you can access that brake light signal either by splicing into the truck's own 3rd brake light wiring or install a fuse tap #F2526 into the fuse position for the…

view full answer...

Answer 3

You can use 7-way trailer wiring with the module part #PP20-702 to provide power to the third brake light of your camper shell/cap. Basically the stop/turn circuits of the trailer wiring need to run to the yellow wires of this module and then the…

view full answer...

Answer 4

Since your trailer uses a combined wiring system where the stop and turn signals run on the same circuit, in order to add a third brake light to your trailer you would need to use a 2-Wire to 3-Wire Converter, like part #118158. This will convert the…

view full answer...

Answer 5

There is a simple solution to get the isolated brake signal from your combined turn signal and brake wiring. You will simply use the Pacer Performance 3rd Brake Light Logic Module #PP20-702. The module filters out the unwanted turn signal. This will…

view full answer...

Answer 6

The easiest way to use your vehicle's 7-way trailer connector to power up the third brake light on your truck cap is to first locate the right and left turn signal wires behind your 7-way. Then simply tap into those and install the Pacer…

view full answer...

Answer 7

The Mini LED Identification Light Kit for Trailers Over 80" Wide #TN26MR actually get installed to your running light circuit. I know they are red, but they are designed to be used as a way to identify the width of the trailer. I recommend…

view full answer...

Answer 8

That's a very good question, so I reached out directly to the manufacturer, Optronics, about where the red wire goes on the Identification Light Kit #MCL22RK3B. They responded by saying you will connect the red wire to the stop/turn signal wire…

view full answer...

Answer 9

Yes you are correct in your assumption. On the Optronics Thinline LED #STL64RB, the Red wire is for turn signal, so this will go either the green or yellow wire on your trailer. The black wire is tail lights so this would go to the brown wire on your…

view full answer...

Answer 10

The Rhino-Rack RTC-Style Roof Rack Tracks will work with the Camper shell to give you the compatible tracks. There are different lengths available and you can cut them down if needed: Rhino-Rack RTC-Style Roof Rack Tracks - 31-1/4" Long…

view full answer...

Answer 11

To isolate the brake light signal on your 2019 Chevy Silverado 2500HD you just need the Pacer Performance 3rd Brake Light Logic Module #PP20-702. You can use the attached installation instructions for the 3rd brake light on your camper shell.

view full answer...

Answer 12

In order to power the third brake light on a truck bed cap you will need the Pacer Performance 3rd Brake Light Logic Module part #PP20-702. The reason you need the module is that the brake/turn signal circuits and trailer lighting circuits are…

view full answer...

How To Wire Dome and Third Brake Light On Leer Camper Shell

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching