Curt Class III # 13703 Adjustable Width RV Hitch Mounting Flange Dimension

Question

Question:

Can I get one more measurement which I havent found on your web site for the Curt #13703? I need to know what is the depth of the upper bend in the bracket measured from underneath. Im trying to determine if it will fit inside my C Channel. I included a picture of the measurement Im looking for.

asked by: Sean B

0

Expert Reply:

As you can see in the photo I've edited for you, the outside to outside dimension of the horizontal bend in the Curt # 13703 hitch mounting flange is 2-1/2 inches.

expert reply by: Mike L

0

click to enlarge

Answer 1

If you look at the installation instructions for the Adjustable RV Trailer Hitch, #13703, linked for reference, you will see that the hitch attaches to the frame rails but not at the receiver tube. The side brackets can be bolted or welded to I-beam,…

view full answer...

Answer 2

The Curt #13703 would mount so that it hangs below the frame members at the rear of the fifth wheel. If you look at the photo and diagram I've provided, you can see how the hitch attaches to the underside of the frame members. The top of the…

view full answer...

Answer 3

Based on the information you gave, to mount the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 I recommend boxing the frame at that location. If you don't wish to box the frame, then I instead recommend using the Curt…

view full answer...

Answer 4

I went out to the warehouse and measured the distance from where the hitch side plate will attach to the web of your motorhome I-Beam, and I got 1-1/4 inches on center. I attached a photo showing the measurement from the outside of the plate to the…

view full answer...

Answer 5

I went to our warehouse and pulled a sample of the Draw-Tite 24-Inch-Long Combo Bar #2852 so that I could measure its outside dimension for you. The bar itself measures 2-9/16-inches on each side and the reinforced collar area at the end of the hitch…

view full answer...

Answer 6

The Curt RV Hitch #13703 has a maximum weight capacity of 3,500 pounds. Regardless of how wide the trailer frame it is on is.

view full answer...

Answer 7

I spoke with my contact at Curt about hitch #13703 and he said that you can install the side brackets on the outside of an I-beam frame by turning them around. I have included a link to the installation instructions for you to view. The hitch can be…

view full answer...

Answer 8

I have a possible option for you, but due to adding another point an extension will reduce your vehicle's capacities by 50%, so you'd only be able to towing something with no more than 250lbs of tongue weight. Instead your only option would…

view full answer...

Answer 9

Curt hitch #13703 fits trailers that have a box frame, C-channel frame, or I-beam frame that is between 22" and 72"; it has mounting holes that may work for you depending on what your trailer measures. As you can see in the accompanying…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Curt Class III # 13703 Adjustable Width RV Hitch Mounting Flange Dimension

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching