Replacement Electric Trailer Brakes for Snowmobile Trailer

Question

Question:

I have to replace the brakes on an enclosed snowmobile trailer. The tire size is 205/65/10 Would it necessarily be the 10inch electric brakes? Also, is there any particular brake or product that handles the off season corrosion better?

asked by: Tom P

0

Expert Reply:

To determine the correct replacement electric brakes you will need to know the weight capacity of your axle and then measure the inside diameter and width where the pads from the brakes touch. If your axles are 3500 lbs and you get 10 inches by 2-1/4 inches AND the brake mounting flange has a 4 bolt pattern then assembly # 23-469 for the right and # 23-468 for the left will fit.

The best brake assemblies as far as resisting corrosion due to moisture are hydraulic brakes, which are used for boat trailers and specially coated for corrosion resistance. However, since you will not be using your trailer for marine applications the Dexter brakes I recommended will be more than adequate.

expert reply by: Chris O

0

Answer 1

Your old assemblies could possibly have nuts on the inside of them for the studs to attach to. You are going to need to access the other side of the assembly to see what holds the studs to them. If it is a broken stud without a bolt head to grab onto…

view full answer...

Answer 2

You can convert your setup to an electric disc setup, to do this you will need first to determine what spindle is on your trailer axles and what wheel bolt pattern you have on trailer wheels. To determine what spindle you have you will have to remove…

view full answer...

Answer 3

It is certainly possible for any axle to wear out enough over time to need replacing. Since the suspension is built into a torsion axle if the suspension part was to wear out pretty much the only solution would be to replace the axle. If the…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Replacement Electric Trailer Brakes for Snowmobile Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching