Instructions for Installing Pop & Lock Custom Tailgate Lock # PAL3300 on 1995 Dodge Ram Pickup

Question

Question:

1995 Dodge Ram 1500. On the inside of the tailgate there are three bolts, does one of these have to come out to bolt pop and lock in? My gate has sprayed in bed liner over these bolts which will make removal more time consuming. Just wanted to know what lies ahead. Which of the bolts will have to come out.

asked by: T. L

1

Helpful Expert Reply:

When installing the Pop & Lock Custom Tailgate Lock, # PAL3300, on your 1995 Dodge Ram Pickup you will need to remove the lower of the three bolts and loosen the other two. I have attached installation instructions for you.

expert reply by: Leah S

1

click to enlarge

Answer 1

The black piece is the bezel in the tailgate lock #PAL3300. The actual handle used to open the tailgate will be the the existing one you have on the truck. I have also included a link to all of the tailgate lock options for your 1996 Dodge Ram 1500.

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

The best modern day size replacement option we have for a 6.00-16 is a 235/80-16 which measures 30-7/8" diameter x 9-3/8" wide. For this, I recommend the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel part…

view full answer...

Answer 6

Although the Tekonsha Prodigy P3 #90195 and Primus IQ #TK90160 electric brake controllers are very similar they do have some key differences as well. For one the P3 is designed to work with electric and electric over hydraulic brake systems. The…

view full answer...

Answer 7

There is not an exact torque specification to pre-load the bearings on a Dexter 8k axle. The spindle nut will need to be tightened by hand until finger tight and then turned another 1/4 of a turn with a wrench. This will be around 15 ft-lbs but you…

view full answer...

Answer 8

The highest capacity trailer spindle we offer is the TruRyde #TRU57FR spindle for 5.2-7K rated axles. The spindles are compatible with a 25580 Inner and an outer bearing with a 1.25 inch ID like the #14125A, #LM67048, or #15123.

view full answer...

Answer 9

I did a little research on your 2001 Dodge Ram 3500 and found that it's max towing capacity is listed as 13,900 lbs. I would strongly recommend you check the owners manual of your truck to see what Dodge lists as the capacity for your truck and…

view full answer...

Answer 10

I believe we have just about everything you need, ideally we'd need you to measure your center bolt and u-bolts to make sure the here will fit. So, for a center bolt you can use the Leaf Spring Center Tie Bolt with Nut #38-3TB which measures…

view full answer...

Answer 11

Hellwig lists the Hellwig Rear Anti-Sway Bar #HE36MR as the correct fit for a 1998 Chevy K2500. As for fitment with the staggered shocks, you shouldn't have any issues and can even see this setup in the attached installation picture below. The…

view full answer...

Instructions for Installing Pop & Lock Custom Tailgate Lock # PAL3300 on 1995 Dodge Ram Pickup

Product Page this Question was Asked From

Continue Researching