Measuring trailer leaf springs requires facing the raw underbelly of your trailer, a dark place you may have never had the pleasure of exploring until now. Fortunately, it’s a surprisingly simple bit of maintenance, and also the first step in replacing leaf springs when you find they are seriously corroded, sagging, or have cracks in the leaves. To learn how to find the right springs for your trailer, read on.Before you start measuring, it will be necessary to jack up your trailer using jack stands: this will allow the axle to hang freely. It’s also a good idea to acquaint yourself with each part of the springs so you’ll know what you’re looking at.Note: Leaf springs should always be installed in pairs so you ensure you are using the same springs on each side of the axle. This will also ensure they ride and wear the same way on each side.
Parts of a Trailer Leaf Spring
Center Pin
The center pin slides into the middle of the leaf spring and holds the leaves together.
Eyes/Slippers
The loops or tails at the end of the springs that attach to the axle with bolts or shackles to keep it in place.
Springs/Leaves
The individual leaves sit over or under the axle and provide a smoother ride by absorbing bumps in the road. They support the weight of your trailer.
How to Measure Leaf Springs
Measuring Leaf Spring Flat LengthThe flat length method will help you obtain a measurement that reflects the length of the springs if they were flat instead of curved. This method is the most accurate way to measure leaf springs because it will work no matter how worn your springs have become over time.A soft tape - or tailor’s measuring tape - may come in handy for easier measuring along the springs’ curve.
For double-eye leaf springs, measurements are usually taken from the middle of the center bolt to the middle of one eye (the measurement should be the same from either side of the bolt). For slipper springs, you’ll need to measure from the middle of the center bolt to the middle of the eye, then from the middle of the center bolt to the tip of the slipper.
Measuring Flat Length for Double-Eye Springs
Measuring Flat Length for Slipper Springs
Measuring Eye-to-Eye / Eye-to-SlipperWhile the flat length method works regardless of how flat your springs have become from time or use, this second approach is faster than the flat length method and still produces results that will help you obtain the correct springs. (It can also easily be done with a traditional tape measure.)
The Eye-to-Eye Method
The eye-to-eye method is as straightforward as it sounds.All it entails is measuring from the center of one eye straight across the spring to the center of the other eye for the final result.
The Eye-to-Slipper Method
The eye-to-slipper method is similar to eye-to-eye: begin at the center of the eye and measure straight across the spring to the tip of the slipper for your final measurement.
Measuring Leaf Spring Width
Sometimes you might also want to get a measurement of your springs’ width. Simply measure across the top of the top leaf to obtain this measurement. (For reference, most trailer springs measure out from 1-¾ to 2 inches wide.)
Measuring Leaf Spring Height
The height of the spring can be found simply by measuring from the middle of the center pin straight up to the top of the eye/slipper. You can alternatively place the leaf spring upside down on a flat surface and measure from the floor up to the center pin for an easier experience.
Where to Go from HereThe final component you will need before selecting the right leaf springs for your trailer is your axle capacity. If you’re unsure of your axle capacity, you can reference the manufacturer’s sticker/plate located on your trailer or check out our article, How to Tell the Weight Rating of a Trailer Axle. Armed with your axle capacity and measurements, you're now ready to purchase your new leaf springs, which can be found here. In no time, your trailer will have the support it needs to haul your heavy loads, whether you’re traveling across town or lugging cargo over rugged terrain. Wherever you decide to go, you and your springs will be prepared for the adventure.
About Beth B. When I explain my position at etrailer to the folks back at home, I usually preface with, “Writing is about 15% of my job. The other 85% is research, hands-on product testing, and putting myself in the shoes of our customers (whom we call neighbors).” At etrailer, I have the opportunity to explore the products I write about in person every day, a privilege many writers don’t have. On a Tuesday morning, for instance, you may find me outside of a 5th wheel collecting pictures of its scissor jacks for an article. On Wednesday, I might switch gears to measure leaf springs in our warehouse, while Thursday is when I’ll finally get behind the keyboard (that is, in between driving off-site to film how-to videos with the team). If you have a question, it’s my mission to not only provide you with an answer, but to equip you with the knowledge and resources you need to face real-world challenges like a pro.
My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…
In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…
Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…
The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…
According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…
We offer replacement brake shoes for 10 x 1-1/2- and 10 x 2-1/4-inch electric drum brakes but no longer for the 1-3/4-inch width you reference. Dexter part #bp04-065 you referenced is a set of replacement brake shoes for electric trailer brakes…
I was able to find the exact replacement amber (1A-S-20A) and red (1A-S-20R) lenses. I did a Google search on kaper2 (or Kaper II), and found replacement lenses. Their replacement lenses are shown as measuring 4 inches long, by 2 inches wide by 3/4…
To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…
There is a trailer wiring harness for the 2020 Ford Edge Titanium with Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #C73FR which will plug in behind the tail lights and give you a 4-pole flat on the Edge to power…