Filter Products
Filter Results
$4.33 - $247.02
$5.80 - $16.43
$9.44 - $21.46
$16.11 - $39.09
$23.91 - $25.69
Filter by Style of Part
$4.33 - $247.02
$5.80 - $16.43
$9.44 - $21.46
$16.11 - $39.09
$23.91 - $25.69
Videos
for Trailer Door Parts
Help Articles
for Trailer Door Parts
Expert Answers
for Trailer Door Parts
I&…
view full answer...You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the…
view full answer...You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…
view full answer...The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.
view full answer...On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…
view full answer...The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part #20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present…
view full answer...I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast…
view full answer...The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this…
view full answer...Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake…
view full answer...If you think the cause for the noise on your 2015 Jayco Whitehawk 24RBS tandem-axle travel trailer is from the normal travel of the suspension components (leaf springs, equalizers and shackle straps), you might switch over to wet bolts. The…
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...Videos
for Trailer Door Parts
Help Articles
for Trailer Door Parts
Expert Answers
for Trailer Door Parts
I&…
view full answer...You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the…
view full answer...You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…
view full answer...The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.
view full answer...On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…
view full answer...The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part #20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present…
view full answer...I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast…
view full answer...The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this…
view full answer...Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake…
view full answer...If you think the cause for the noise on your 2015 Jayco Whitehawk 24RBS tandem-axle travel trailer is from the normal travel of the suspension components (leaf springs, equalizers and shackle straps), you might switch over to wet bolts. The…
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...