Expert Answers about Mitsubishi

• Parts Needed to Allow Swagman XTC-2 To Carry Fat Tire Bike
• I have a solution for you, but the the tires on your bike are 2.8" wide and the Swagman XTC-2 # S64670 can only accommodate tires up to 2.5" wide in the included wheel holders. You'll need swap the wheel holders out for the Swagman Fat Tire Bike Adapters # S64674 to allow your oversized wheels to seat comfortable in the holders. These adapters can house wheels up to 5" wide.
  view full answer...


• Recommended Wiring Harness for 2014 Mitsubishi RVR
• We have just what you're looking for. I recommend using the # C59496 because we've found that the converter boxes are a bit more reliable over time, so it's going to be a harness that can withstand the test of time. This harness will need to be hard wired into your tail lights, since there are no plug and play harnesses available for your 2014 Mitsubishi RVR. If you don't already have a hitch and ball mount kit, I've added some recommendations for those below, as well. Hitch: Curt # C13079 Ball...
  view full answer...


• Parts Needed to Install a Trailer Brake Controller on a 2006 Mitsubishi Raider
• I spoke with my contact at Tekonsha and he stated that they have not tested the brake controller wiring harness on a 2006 Mitsubishi Raider. So, while it is possible that it will fit if the truck has a factory tow package that includes a 7-Way trailer connector, since it has not been tested I cannot say for sure if it will or not. Instead, you can hardwire the controller. If the truck does not have a trailer connector, you will need to first install # 118323. I have included a link to...
  view full answer...


• Recommended Trailer Hitch Receiver and Other Parts to Tow with a 2016 Mitsubishi Outlander Sport
• The trailer hitch receiver I recommend for your 2016 Mitsubishi Outlander Sport is the etrailer # e63AR. This is a Class III hitch with a 2 inch receiver opening. Also, a Class III hitch receiver has a 2 inch opening. The 2 inch accepts a larger variety of bike racks and other accessories than a 1-1/4 inch will. If it turns out you need to carry a 1-1/4 inch accessory it's also a lot easier to use a reducer from the 2 inch than it is to go the other way. Since you said you're going...
  view full answer...


• Circuit Breaker Rating for +12V Auxiliary Power Circuit on 7-Way Wiring
• In a 7-way wiring set-up the +12V auxiliary power circuit that is present to power a jack or top off the charge on a trailer battery is usually protected with a 40-amp breaker. The 30-amp breaker is appropriate for the brake controller. The 40-amp breaker # 9510 has an auto-reset feature that will re-connect the circuit once any overload condition has been removed. The copper-color post connects to the battery.
  view full answer...


• Parts Needed to Prepare 2002 Mitsubishi Montero Sport for Towing Trailer with Electric Brakes
• In order to install a trailer brake controller like the excellent Prodigy P3 # 90195 in your 2002 Mitsubishi Montero Sport you will need an installation kit # ETBC7 and if you don't already have a 4-pole flat wiring harness on the Montero, one of those as well. If you need a 4-pole harness you can use kit # 119178KIT from TowReady; I recommend this kit because it includes the circuit tester required for identifying the wire functions on the Montero. I have linked for you a video showing...
  view full answer...


• Tire and Wheel Combination Size 205/65-10 with 4 on 4 Bolt Pattern
• You are correct that your 20.5 x 8.0 x 10 sized tires are the same as 205/65-10 sized tires. With a 4 on 4 bolt pattern we have tire and wheel combinations that I've linked for you. The highest weight capacity of our selection there is # AM3H460 and # AM3H470. They're the same tire on a different wheel. One being a white powder coat and the other is galvanized. They have a maximum capacity of 1,650 pounds at 90 psi per wheel.
  view full answer...


• Trailer Hitch for 2021 Mitsubishi Outlander
• If you have a 2021 Mitsubishi Outlander that's a PHEV, the etrailer # e48KR is fit. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part # 118482, a # D-28 ball mount along with a # PC3 hitch pin and a trailer ball. For a 1-7/8 inch ball, use # 40038 or # 63845 for a 2 inch ball. If you have an Outlander Sport, the Curt # C13079 fits all 2021 Outlander Sport models except for the PHEV. For a trailer wiring harness, use # TK67VR. You'd use the same ball mount...
  view full answer...


• Parts Needed to Flat Tow a 2006 Jeep Wrangler and a 2005 Mitsubishi Eclipse Spyder
• There are 5 components that you will need to flat tow a vehicle behind a motor home. You will need a base plate kit, a tow bar, tail light kit, safety cables and a supplemental braking system. It looks like you will be better off towing your Jeep rather than the Eclipse. After doing some research on your vehicles, it appears that there are no base plate kits available for your Eclipse. Base plate kits are the only component that must be vehicle specific. I spoke with my contacts at Roadmaster...
  view full answer...


• Class III Hitch and Trailer Wiring Harness for 2018 Mitsubishi Outlander
• We can help you with a hitch and trailer wiring harness for your 2018 Mitsubishi Outlander. I suggest the 2-inch Class III Curt hitch # C13163. This hitch includes all required mounting hardware as shown in the linked video. Written instructions are linked for you too and these tell you exactly what tools you need to bolt on the hitch. No drilling is necessary. For wiring use kit # 118482 if you do NOT have the towing package; use part # 118277 if you DO have the tow package. Install...
  view full answer...


• Recommended Roof Rack For 1996 Mitsubishi Delica L300 High Roof Van
• I checked with Rhino-Rack and the correct roof rack for your 1996 Mitsubishi Delica Van is as follows: -Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 54" # RRVA137B-2 -Rhino Rack Gutter Mounted Legs - 8-3/10" Tall # RL210S2 -Track-Mounted Leg Adapters # RRVA-FK1
  view full answer...


• Electric Brake install 2000 Coleman Sedona
• In order to make recommendations for brake assemblies and hub/drums, I'll need some more information. I'm assuming your pop-up currently uses idler hubs. In order to recommend the proper brake assemblies and hub/drums, I'll need the reference numbers off of your inner and outer wheel bearings. To get the correct hubs with wheel bolt patterns that match your existing wheels, I'll need to know the lug bolt pattern of your existing hubs, which will likely be 4 on 4 or 5 on 4-1/2. Once I...
  view full answer...


• Parts Needed to Add 4-Pole Flat Trailer Wiring Harness to 2010 Mitsubishi Outlander
• It sounds like the connector on your 2010 Mitsubishi Outlander that you are referring to may be the one that mates with the wiring harness connector shown in the linked photo. This connector is part of the Curt custom-fit harness # C56102 and the Tow Ready # 118518, both of which fit your 2010 Outlander. Both of these wiring kits provide you with a 4-pole flat connector to activate your trailer's lighting functions. An installation video is linked for you.
  view full answer...


• Trailer Wiring Harness For A 2023 Mitsubishi Outlander
• The T-One Vehicle Wiring Harness # TK46VR is confirmed to fit your 2023 Mitsubishi Outlander per the manufacturer. I like the T-One harness over the other harnesses because it has a more reliable powered converter box that will give you a longer running time than the others. This custom harness will plug into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies to access this harness....
  view full answer...


• Recommended Upgraded Crossbar System for a 2017 Mitsubishi Outlander With a Bare Roof
• I spoke with Thule and they were able to confirm that there actually are not any corresponding fit kits for the Traverse Feet and your 2017 Mistubishi Outlander with a slick roof. With that being said, your only option is to upgrade your roof rack to a newer system like the Yakima CoreBar Crossbars # Y00421, with the SkyLine Towers for Yakima Crossbars # Y53TR and the Landing Pad 11 for Yakima SkyLine and Control Towers # Y00233. This system will work with your bare roof, has a maximum...
  view full answer...


• Rhino Rack Crossbars for 2012 Mitsubishi Outlander Sport w/ Flush Mounted Roof Rails
• For a 2012 Mitsubishi Outlander Sport with the flush-mounted rails, all you would need is the Rhino Rack crossbars, part # RRVA126B-2 and the # RRSX031 leg kit. The leg kit is designed to attach directly to the flush mounted rails, and no fit kit is necessary. I have confirmed this with Rhino Rack.
  view full answer...


• Recommended 205/75R14 Tire Replacement for Camper Currently Using Bias Ply Tires
• I recommend the Kenda Karrier ST205/75R14 Radial Trailer Tire - Load Range C # AM10234. These Kenda tires are the same size tires that you're currently using, but are a radial tire, opposed to the bias ply tires that are currently on your camper. Radial tires have a less stiff of a sidewall and are going to provide you with better ground contact, traction, stability, and tread wear. Additionally, because the plies of the tire do not overlap, they're less prone to heating up; heat is the...
  view full answer...


• Recommended Flat Tow System For A 2018 Mitsubishi Mirage
• When it comes to flat towing your 2018 Mitsubishi Mirage I recommend The Demco Kar Kaddy X Tow Dolly w/ Disc Brakes - Tilt Bed Frame - 4,800 pounds - Wide Tread # DM9713093. The Demco Kar Kaddy has a maximum vehicle weight capacity up to 4,800 pounds. It is ideal for cars with front-wheel-drive with automatic transmissions. It has a tilting bed frame which allows for an easy loading and unloading of the vehicle. The Kaddy includes a full LED DOT lighting package which includes the brake,...
  view full answer...


• Which Trailer Wiring Harness for 2018 Mitsubishi Outlander
• As long as your Outlander isn't the plug in hybrid (PHEV), I'd recommend the # 118482 for vehicles without the factory tow package or # 118277 for vehicles with the tow package. If your vehicle has the tow package, it will have the tow package electrical connector located behind the driver's side bulkhead in the cargo area, to the rear of the wheel well as shown in the provided photo. You could also call your Mitsubishi dealer with the VIN, and they should be able to tell you how the vehicle...
  view full answer...


• Which Lock Core Do I Need For My Thule AeroBlade Edge Roof Rack?
• The best way to add locks to the Thule AeroBlade Edge Roof Rack is to use Thule One-Key System Lock Cylinders - Qty 4 # TH450400. This comes with 4 lock cores for each tower of the Thule AeroBlade roof rack and it comes with 2 matching keys and the master key for changing out lock cores. The Replacement Lock Cylinder for Thule Racks and Carriers - N197 # THLOCKN197 is specifically a replacement lock core if your roof rack has the N197 key code stamped into the lock core. If you have that...
  view full answer...