The T-One Vehicle Wiring Harness # 118275 connects to the factory tow package wiring connector. You will need to verify with Land Rover that your 2016 Range Rover Sport Autobiography has the wiring and connectors from the factory. You will then be able to connect a Redarc Tow-Pro Liberty Brake Controller # RED24FR with their Wiring Harness # RED87FR to your Range Rover.
If you do not have the factory tow package you will need the Universal Wiring Harness w/ ModuLite and Brake Controller... view full answer...
If your 2015 Land Rover Range Rover Sport has the factory towing package, it will have a small plug somewhere on the rear end that allows you to easily install a 4 way connector for towing. The Tekonsha T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector # 118681 is exactly what you need. If your Range Rover Sport was not equipped with the factory tow package, I recommend using the ZCI Circuit Protected Vehicle Wiring Kit # 119250KIT which will provide you... view full answer...
The trailer wiring harness kits we have for your 2017 Land Rover Discovery Sport are all the 4-pole type and all of these aftermarket products require hardwiring. We do not have a plug-and-play 7-way option.
All are shown on the linked page and all will install in the same manner. I suggest Curt kit # C59236 for its higher output current capacity. A helpful installation article is linked for you.
You can convert this 4-pole connector type to a 7-way through installation of our # ETBC7... view full answer...
You won't want to use an extender, because doing so would lower the hitch capacity by half, which wouldn't work for you. This being said, I believe we have a solution for you that will get you all the length you need and almost all the elevation.
You don't mention how long your existing ball mount is, but if it's typical like the # AMSC2 at 9-1/2 inches from hitch pin hole to the center of the hole where the trailer ball mounts, the Curt # D900 is 15-1/4 inches long from hitch pin hole... view full answer...
In order to connect the LED Light Kit # 98174LED to your 2015 Land Rover Evoque you will need a trailer wiring harness with a 4-Way flat trailer connector, such as the ZCI Circuit Protected Vehicle Wiring Harness with 4-Way Flat Trailer Connector and Installation Kit # 119250KIT. This wiring harness will install on your Evoque without requiring you to cut or splice into the factory wiring on your vehicle. The harness has zero-contact interface sensors that read the signals of the factory... view full answer...
The # APT4 Tandem-Axle Hanger Kit will provide about 4 inches of clearance from the center of the trailer axle to the bottom of the trailer frame, with no load on the axle. This is assuming that your axle tube is 3 inches diameter. If your axle tube is smaller the height will be sightly less. The curve of the springs you select will have some affect also.
I would recommend that you go with the APT5 hanger kit because all of the hangers are the same height and it will make it easier to... view full answer...
I can't tell by the pictures if all the parts are damaged but the Thule roof rack in the pictures consist of the old style 58 inch square bars, Podium foot pack, and fit kit # THKIT3112.
The basket doesn't look like a Thule product to me. I'm fairly sure it's the Yakima LoadWarrior # Y07070 or possibly the MegaWarrior # Y07080. Look at the picture I've attached of the mounting brackets off the LR3 compared to the Yakima brackets.
Of course, if you wanted, the basket can be replaced... view full answer...
If you have standard size axles that you are installing the Electric Trailer Brake Kit # AKEBRK-7-SA on then you can choose from the following options:
5,200 lb Axle - Kit # BK3-310 (Grease Seal 2.125" ID) or Kit # BK3-300 (Grease Seal 2.250" ID)
6,000 lb Axle - Kit # BK3-110 (Grease Seal 2.125" ID) or Kit # BK3-100 (Grease Seal 2.250" ID)
7,200 lb Axle - Kit # BK3-210 (Grease Seal 2.125" ID) or Kit # BK3-200 (Grease Seal 2.250" ID)
Since you do have an older Airstream Overlander you... view full answer...
The Curt Trailer Hitch Receiver # C13396 that you referenced will not interfere with the spare tire on your 2015 Land Rover Discovery Sport since it is inside the rear hatch. You can use the linked instructions to help install this hitch on your Discovery Sport.
Keep in mind that all non-trailer loads, like a bike rack or cargo carrier, must be supported by a stabilization strap, like part # 18050, to keep in line with the warranty from Curt.
We do have a wiring harness that has a 4-Way... view full answer...
Curt Class III hitch # 13456 will fit your LR3 with a 2-inch receiver. This is a no-drill installation and you can refer to the linked instructions and the install video showing a 2006 LR3 to see the process.
For a trailer brake controller I recommend Curt's innovative wireless Echo # C51180 which offers easy plug-in installation and that lets you use it in any vehicle that has a 7-way.
If your LR3 has no wiring at all you will use 4-pole kit # C59496 along with 7-way wiring upgrade kit... view full answer...
Thank you for the picture! Based off of that it looks like your 2016 Land Rover Range Rover is either an Evoque or a Sport. If you have an Evoque then I recommend the Curt Trailer Hitch Receiver # C13128 but if you have the Sport use the Curt Trailer Hitch Receiver # C13243.
Both options give you what you need to carry a hitch mount bike rack but a stabilizer strap like part # 18050 must be used for non-trailer products (like a bike rack) to keep in accordance with the Curt warranty.
For... view full answer...
While we do not have any grille guards that will work with your 2007 Land Rover LR2, we do have a wide variety of roof racks that'll work great.
If your vehicle has a slick roof, I recommend going with the Thule WingBar Evo Crossbars # TH711400, with the Evo Clamp Feet for Thule Crossbars # TH710501, and the Fit Kit for Thule Evo Clamp and Edge Clamp Roof Rack Feet # TH145123.
These crossbars have integrated t-slots to accompany any roof mounted accessory, has a nice weight capacity at... view full answer...
Yes. For a 2020 Land Rover Defender with 255/60r20 tires the # TC2828 will fit those tires and are a good choice. You can get the chains with the cams included with the Titan Chain Snow Tire Chains w/ Cams - Ladder Pattern - V-Bar Link - 1 Pair # TC2828CAM instead of adding the Titan Chain Multi-Arm Rubber Tire Chain Adjuster for Heavy Trucks - 1 Pair # TCMA3.
I've linked a review video of these chains for you to have a look at. view full answer...
The kit you're looking for to add a Rhino Rack Pioneer Platform and Back Bone system to your 2016 Land Rover LR4 is available with part # RR83AB; this kit contains the Rhino Rack 52107F Pioneer Platform and RD4B1 Back Bone kit. These have been confirmed to fit your LR4.
You could also get a 56" wide platform with part # RR75TB and use the Rhino-Rack Backbone Mounting System for Pioneer Platform - Land Rover LR4 # RRRD4B1. view full answer...
Though we do not just sell the rubber that slides over the grip we do have the full piece.
The Replacement Quick Grip Mount Assembly - Thule Ascent, Atlantis, and Force Cargo Box - Qty 1 # TH05738 comes with everything that you will need and it fits the following racks:
Ascent (TH602, TH603, TH604, and TH605)
Atlantis (TH685, TH685BXT, TH685XT, TH686, TH686BXT, TH686XT, TH686B, TH687, TH687BXT, TH687XT, TH687B, TH688, TH688BXT, TH688XT, and TH688B)
Force (TH623, TH624, TH625, TH626,... view full answer...
Unfortunately we do not have any hubs that use those bearing numbers. Your options would be to remove your old spindle and install a new spindle such as # TRU24FR with compatible hub and drum such as # 84546UC3. You could also replace your entire axle with one such as # 35545E-ST-89, which is rated for 3,500 lbs and has electric brakes. In order to determine the correct axle you would need to measure from hub face to hub face and spring center to spring center like in the accompanying photo.... view full answer...
When it comes to getting the replacement hardware for The Curt Hitch # C13128 on your 2018 Land Rover Evoque The Replacement Hardware # RHK will be the correct hardware for you. When ordering you will see a tab you can type a number into and a drop down menu where you choose what brand of hitch you have. Make Sure to choose Curt and then type out the C13128.
I attached a link that will take you directly to the cart with the correct part you will need. view full answer...
You'll need the # 3035-P brake controller wiring harness. We've found the connector either directly above the brake pedal or nearer the center console. The connector will be gray in color which should make it easier to locate. We do not have an ebay store, we sell directly from our website, etrailer.com. view full answer...
To install the 50" Yakima JetStream crossbars # Y00425 on your 2017 Land Rover Discovery Sport you'll also need the BaseLine Towers # Y28TR as well as fit kits # Y06127 and # Y06154.
When it comes to bike capacity there are a few factors that come into play, but if your bikes are lightweight then you can potentially fit 5 or 6 bikes on 50" crossbars. The factors that you need to take note of are the weight of your bikes, the width of the bike racks you plan on using, and the geometry of... view full answer...
The wiring adapter you need to install a Prodigy P3 trailer brake controller # 90195 in your 2011 Land Rover LR4 with tow package is item # 3035-P. view full answer...
Go To Results