Normally a Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 would be added to a Curt T-Connector Vehicle Wiring Harness # CU94FR on your 2020 Hyundai Santa Fe to give you the circuits you are needing. The additional 5th wire is tied into the reverse light circuit on your Santa Fe to power reverse lights or typically a Reverse Lockout Solenoid # T4748800. That solenoid would prevent the brakes from activating when you drove in reverse.
Since you have a 7-way already you will only... view full answer...
If you have the same Rhino-Rack roof rack parts # RRVA137B-2, # RRRLKVA, and # DK360 like we installed on a similar 2017 Hyundai Santa Fe then that would mean your 2500 Series Legs have about 40-1/2" of space between them.
With this being the case you can either use the Rhino-Rack 38" Long Fairing # RRRF2 or the Inno 40" Long Fairing # INA261. view full answer...
The 4-pole trailer wiring harness kit you can use for your 2018 Hyundai Santa Fe SE without the factory tow package is Curt part # C56184. This kit's installation is pretty straightforward; plug in the custom-fit connectors at the back of your taillights and then run one single power wire up to your battery. The linked instructions, help article and installation video will show you the entire process.
I recommend using dielectric grease # 11755 on all of the connectors when you install... view full answer...
I recommend the etrailer Trailer Hitch Receiver # e28AR for your 2023 Hyundai Santa Fe. After installing the etrailer hitch onto your vehicle it will provide you with a clean off the factory look with only the 2 inch receiver head showing. I like this hitch over the others that we offer because it has a matte black powder coating that will make scratches and scuffs less visible than the other hitches we have.
When installing the trailer wiring harness, I recommend the Curt Wiring Harness... view full answer...
Actually, we have an FAQ article that specifically addresses this. You can see the article by clicking the provided link.
You'll need to choose a hub/drum that uses the same inner and outer bearing as your existing idler hub, and the hub/drum would need to have the same bolt pattern as you existing hub so you can use the same wheels and the hub you choose would need to be compatible with your existing wheel diameter. Your axle will need to have the brake mounting flange to provide an attachment... view full answer...
In order to install an electrical hookup with a brake controller kit on your 2009 Hyundai Sante Fe, you will need the following parts:
- Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56346 (if your vehicle has the factory tow package) or # C56078 (if your does not have the factory tow package).
- Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat # ETBC7
- Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles # 90885... view full answer...
I recommend going with a hitch mounted bike rack that attaches to a swing away system because of ease of use and potential clearance issues. If your 2020 Hyundai Sante Fe doesn't already have a hitch receiver the Curt Trailer Hitch Receiver item # C13195. I have attached a picture of what it will look like installed on a Sante Fe.
For a swing away adapter, I recommend the Yakima BackSwing Swing Away Hitch Extender for Bike Racks - 2" Hitches item # Y02483. The pivoting hitch extender lets... view full answer...
If your 2019 Hyundai Santa Fe has the tow package then you want to use the Curt T-Connector # CU94FR which has the 4-Way Flat connector that you asked about and plugs into the factory connector which is located under the vehicle, behind the rear bumper, on the driver’s side.
You said that you already have the trailer hitch for towing, but you didn't mention a ball mount kit. If your trailer hitch has a 2" receiver like the Curt # C13195 which fits a 2019 Santa Fe then I recommend the Curt... view full answer...
Since there aren't any 7-Way trailer connectors that will plug into the 2015 Hyundai Santa Fe you will need to hardwire one in. Half the work is already done since you have a 4-Way installed already. All you will need is kit # ETBC7 to add a 7-Way and retain the 4-Way. I have included some links that show and explain the ETBC7 installation for you. view full answer...
When it comes to The Curt Hitch # C13153 on your 2017 Hyundai Santa Fe Ultimate without a brake system per our records it shows it can tow up to 1,653 pounds, but I would recommend checking your vehicle's manual for the proper towing capacity.
I attached a link you could follow below. view full answer...
The Electric Trailer Brake Kit # AKEBRK-2 comes with one left and one right brake assembly and included mounting hardware. The drums are not included. I would need to know what your inner and outer bearing numbers are on your current axle and I will be able to tell you what you need.
The nuts and lock washers # BRKH7 are sold separately. These brakes will work with 10 inch 12 inch and 13 inch wheels, and have an axle rating of 2,000 pounds.
I attached a review video link below. view full answer...
In order to install a 7-Way trailer connector and a brake controller on your 2012 Hyundai Santa Fe SE you will new 2 parts. First you will need installation kit # ETBC7. This kit provides the 7-Way and the wiring and accessories needed to install it and hardwire in a brake controller. Your factory 4-Way will plug into the back of it.
The other part needed will be the brake controller itself. I recommend the P2, # 90885, because it is easy to set up and use and it's reliable. I have included... view full answer...
For a more cost effective option to go with the Yakima BackSwing Swing Away Hitch Extender item # Y02483, I recommend the Kuat Transfer V2 Bike Rack for 2 Bikes item # KU84FR. It will still function with the swing away adapter and has the capacity to hold two bikes up to 60 lbs apiece. view full answer...
If your 2013 Dodge Durango came with a factory installed 7-way trailer connector, then you can use the Tekonsha Brake Control Wiring Adapter, # TK93VR, to connect the Primus IQ Brake Controller, # TK90160. The factor brake controller port on your Durango should be located to the left of the emergency brake pedal taped to another harness. I have attached installation instructions for you to check out.
If your Durango does not have the factory 7-way trailer connector, then you will not... view full answer...
To convert the 4 pole plug # 118415 on your 2009 Hyundai Santa Fe to a 6 pole that will connect to your trailer, you can use the Hopkins Adapter # 37175 if your trailer uses a round connector, which can simply be plugged into your existing 4-pole connector.
If your trailer has a 6-way square connector, you will instead need to use the Hopkins 6-Pole Square Kit # 37995. For this you will actually need to hardwire the harness into your vehicle's 4-pole wires. The kit comes with both connection... view full answer...
You are correct that the first step in carrying 2 kayaks on the roof of your 2013 Hyundai Santa Fe Sport with the Panoramic Sunroof is a roof rack. I recommend using the Thule WingBar Evo roof rack system because it looks sleek, has an easy mounting system for accessories, and is simple to install on your vehicle. For this you will need the following parts:
53" WingBer Evo Crossbars - # TH711420 Black or # TH711400 Silver
Evo Clamp Feet - # TH710501
Fit Kit - # TH145059
Lock Core Kit -... view full answer...
We do have a wiring harness to fit your 2019 Hyundai Santa Fe. The correct part is # CU94FR.
Since you have the tow package there's a connector under the rear bumper on the driver's side. The harness plugs in here and then you need to find a good secure location to mount the converter box. It mounts with included double-sided tape you just need to make sure the location you choose allows for the 4-way connector to reach the connector on the trailer. You also want to make sure the converter... view full answer...
I have a way for you to safely transport your dual sport bike on your vehicle. I went ahead and looked up the specs for your 2013 Hyundai Santa Fe, and it has a maximum gross towing weight capacity of 2,800 pounds. If this is the case, the maximum tongue weight capacity of your vehicle is 280 pounds.
With this tongue weight capacity, you cannot safely mount via a hitch carrier that requires tongue weight. This is because no matter what hitch you use, your sport bike exceeds that 280 tongue... view full answer...
We do have the parts you need to install an electric trailer brake controller, like the popular Prodigy P3 # 90195, in your 2017 Hyundai Santa Fe but unfortunately your vehicle does not have a factory connector to just plug one in. So there isn't an adapter available.
Instead you need to convert your existing 4-way trailer connector to a 7-way using our # ETBC7 kit. The kit includes the 7-way connector, which you need to plug in a trailer with brakes, as well as the wiring to install... view full answer...
There are 5 basic components you will need to flat tow a vehicle: base plates, tow bar, safety cables, lighting, and supplemental braking. You will also need to check the vehicle owners manual to determine if the vehicle can be flat towed and for the proper procedure for towing the vehicle.
Base plates provide a safe attachment point for the tow bar. There are several options for a 2004 Hyundai Santa Fe. I recommend the popular Roadmaster XL # 1619-1. The most popular tow bar for these... view full answer...
Go To Results