The 30 amp controller of the Go Power Flex kit part # 34272628 can only take one power and ground cable but the solar panels can connect to each other on top of the RV to then supply the power of multiple panels on that one set of power cables. view full answer...
The monitor for the TireMinder i10 TPMS # TM29FR does need to be plugged in. It comes with a power cord that you can either plug into to a USB outlet or you can use the included adapter to plug into a 12v cigarette outlet. view full answer...
The Timbren Rear Suspension Enhancement System, part # TFRF53A, and the Timbren Front Suspension Enhancement System, part # TFFF53B, are both compatible with your 2017 Thor Windsport Motorhome. Unfortunately, neither of these Timbren systems can be installed on your 2017 Thor Windsport Motorhome without lifting the motorhome.
I have included a product description link and a video installation link below. view full answer...
When installing the Roadmaster Rear Anti-Sway Bar Item # RM-1139-147 you can reuse the bolt holes in your frame for your links as long as they allow the anti-sway bar to sit level. If they do not you will need to drill new holes.
I've attached an installation video where Shane will walk you through installing the # RM-1139-147. view full answer...
To manually reset your Lippert Ground Control part # LC358590 you need to hold down the retract and enter buttons at the same time. Try that but if you still get an error code you most likely have a low voltage battery that needs to be charged. Or if that's not it the wiring of the system needs to be checked out. view full answer...
I spoke with my contact at Camco regarding your RV Power Defender Circuit Analyzer # CAM55312. He said that if the blue surge protector light is no longer illuminating on your unit then it has experienced a surge episode (and protected your RV!). This may have happened with your 30 amp home outlet or it could have happened the previous time you used the analyzer at a campsite. Since this particular model provides one-time-event protection, it is no longer able to provide surge protection... view full answer...
If it isn't held in with screws there should be some type of adhesive on it; I wish there was an easy way for me to tell you exactly how but realistically there isn't going to be a way that is particularly easy for you to remove your assembly if it is stuck on with adhesive. The Lippert Components 12" x 21" Inner and Outer Entry Door Window Frame with Seal # LC363369 just snaps together so it is possible you may be able to unsnap your assembly as well. view full answer...
The Portable Power Watchdog Surge Protector with Bluetooth part # HU97FR can be reused after being tripped. That said, you will need to replace the surge module first (Replacement Surge Module for Power Watchdog Surge Protector part # HU48FR). view full answer...
When installing the Roadmaster Rear Anti-Sway Bar # RM-1139-146 you do want the trailing arms of the sway bar to be as parallel to the ground as possible. I can see what you're talking about, and they do look like they're angled slightly upwards. If you watch at the start of the videos where the road test is done, you can get a pretty good idea of what it's supposed to look like when installed. It may not be able to be installed completely level because of different components that are... view full answer...
The psi max is when the tire is inflated cold. As you drive and as ambient temps change the psi will increase, but the manufacturer accounts for that change in their psi recommendations. You want to inflate to the max psi prior to your trip to give you the rated load capacity as well as the best traction. Adjusting that can cause your tires to not function as intended and overheat which is the leading cause of failure. So the # LHAW133 you asked this from would be 80 psi inflated cold. view full answer...
The Command Electronics Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens - Qty 1 # CE44VR does not come with any instructions but the wiring diagram can be found on the rear of the lens housing if you pull back the foam pad. We've also covered this in detail in our review video, which I've attached to this answer and outlined below.
Red- stop and turn
White- Ground
Black- Tail Lights
Purple- Reverse/Backup view full answer...
Your 2019 Thor Four Winds 24E Motorhome is built on a Ford E-450 chassis so the plug you're going to need will be located behind the storage (coin) compartment above the radio (see attached).
If you don't already have a brake controller I highly recommend the Prodigy P3 # 90195 which will connect to that plug using the Adapter # 3034-P. I really like the P3 because it has an LCD screen that communicates directly what is going on with minimal codes.
Attached are some photos for you to... view full answer...
The zippers on the Solera Family Room for RV Awnings # LC362235 are double-sided with pull tabs on both the inside and outside of the room so that you can open and close door section from either side. view full answer...
Since you want the slightly longer queen size mattress the best solution might be the Denver Mattress Supreme Euro Top part # DE38ZR which has rounded edges on the bottom which will work better in the limited area you mentioned having with the slide retracted. Flexing the mattress a little bit won't hurt it. view full answer...
Unfortunately there is not a kit that that'll convert your manual opening MaxxFan roof vent to a powered roof vent.
To get a powered roof vent you'd have to replace the entire unit with a powered unit like the MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote # MA00-04500K.
This is a powered unit that has a 12V reversible fan that also includes a handheld remote so you can set the thermostat, and change the speed/direction of the fan. view full answer...
I reached out to Camco regarding a weld-on installation of the bushings for the Gen-Turi RV Generator Exhaust System # CAM44461. According to my contact, this is a perfectly acceptable way to install the system. When possible, welding will always outperform something like the clamps that are included when performed by a professional. That would be the most secure way to install this and remove any need for concern. view full answer...
Unfortunately, your RV information does not indicate what vents/screens that you would have. That being said, 14"x14" vents are significantly more common than 13"x13". The replacement screens that we carry, like the Replacement Screen Frame with Screen # BVC0573-32 which fits the Ventline Ventadome Roof Vent # V2119-603-00 fit inside a 14"x14" roof vent, the screen itself is not 14"x14".
The easiest way to identify the correct replacement parts is with model numbers. If you can provide... view full answer...
In order to add the grid lines to your Voyager RV Backup Camera w/ Night Vision - Rear Mount # VGR84VR you are going to need to get into the menu screen on your monitor like # VO34FR, and through the settings you'll just need to toggle the marker lines ON/OFF.
You can find more information on page 6 of the owner's manual, or you can check out the attached image. view full answer...
The correct air bag kit for a 2018 Thor 24HE on a Ford E-350 Cutaway Chassis is the Firestone Ride-Rite Air Helper Spring Kit part # F2061. This system is designed to provide rear end support to reduce sag. It is not designed to lift the rear but in many cases we do see this happens with enough pressure. That said, whether or not it will provide enough lift to prevent bottoming out on any one particular driveway is anyone's guess as the amount of lift and slope of driveway are variables... view full answer...
The install of the Roadmaster Exact Center Steering Stabilizer part # RM47MR does not require more than 150 ft lbs of torque. It's not a great idea to use a torque wrench as a breaker bar to loosen hardware. And I'm saying that as someone who has borrowed their current employer's expensive torque wrench and done so in the past. It might be fine but it has potential to screw up the calibration of the wrench. view full answer...
Go To Results