Yes, we have instructions for the Draw-Tite Trailer Hitch, item # 75556, linked on our website, see link. This hitch installs easily with just 4 bolts and 4 conical washers. I've also linked an install video on a 2009 Vue. view full answer...
I attached a picture that I took from the install instructions for the Roadmaster base plate kit part # 154-3 that you referenced for you to check out. We do not have any install pictures at this point.
I also attached a help article on flat towing and the install instructions for this base plate kit. view full answer...
The Curt Manufacturing Class I Trailer Hitch Receiver with Drawbar, item # 11114, for your 2008 Saturn Sky, will not void the vehicle warranty as long as all of the towing limitations of the vehicle and the hitch are closely adhered to.
There is a federal law called the Magnusson-Moss Warranty Act, which states that unless the modification to your vehicle, in this case the hitch, caused the problem your warranty must be honored. This being said you will need to use common sense precautions... view full answer...
The Timbren Rear Suspension Enhancement System # TGMRVUE for the 2008 Saturn Vue requires temporary removal of the rear coil springs and permanent removal of the factory bump stops. This kit bolts on to your vehicle frame using vehicle-specific brackets. It is necessary to raise the rear end of the vehicle to allow the rear suspension to hang freely for the installation. I have attached the written installation instructions from Timbren; please note these make no reference to removal of... view full answer...
The Inno Roof Rack with bar part # INB127 will install its clamps over the trim into the door of the vehicle. Your fit kit, part # INK124 will hook over your door frame and install the foot pack into the bases over the side of your roof's lip. I've included the illustrations from the instructions as a point of reference to how this should look installed.
I've included an installation video for the 2017 Nissan Maxima so you can see an installation process on a similar 4 door sedan. view full answer...
The Roadmaster Tow Bar Wiring Harness Part # RM-154 requires that you locate holes through which you can pass the 4-pole RV connector wiring. It is usually possible to locate rubber grommets that already have wiring passing through them if you remove carpet and trim panels in the rear of the vehicle. The tail light wiring may also provide an access point; you can try removing the driver-side taillight assembly to see if there is a grommet you can use.
Once routed to the underside of the... view full answer...
I spoke with my contact at Camco and he informed me that the Backflow Preventer part # CAM23303 that you referenced should be installed after the water pump. view full answer...
The Camco RV Portable Propane Campfire # CAM58041 has a built-in regulator so it can connect directly to your RV's high-pressure propane feed. My contact at CAMCO confirmed this is the preferred installation method.
It comes with an 8 foot hose for you to use to connect to your RV.
The part # CAM59143 does come with fittings that would allow it to be compatible with the fire pit as well. view full answer...
I spoke to my contact at Curt about installing Hitch # 13591 on your 2006 Saturn Vue Redline. She state that if you measure from the bottom of the bumper beam down 2 inches, that is where the top of the receiver tube will be and that should give you some idea of what will need to be trimmed. The hole will also be about 2-1/2 inches wide.
To perform this trimming, I recommend using an electric rotary tool of some kind. If you must use hand saw, it will have to have very fine teeth. Otherwise,... view full answer...
The connection you will need to use is most likely the chassis connection in the case of the brake controller. You will want the connection that is hot at all times ran to the brake controller so that the trailer brakes can be operated at any time whether the ignition is on or not. The brake controller should be wired through at least a 20 amp circuit breaker, item # PK54520, and a 30 amp circuit breaker, item # PK54530, if the trailer has more than 4 brakes or the brake controller calls... view full answer...
You should not have to cut anything to install Draw-Tite Trailer Hitch, part # 75556. The hitch receiver opening will sit just below the rear fascia. The only thing you may want to do is temporarily un-hook the exhaust from the hanger near the rear to make getting the hitch in place and installing the bolts easier.
Other than that, this hitch is a straight-forward, no-drill install. I will include a link to the instructions so you can read through the process. I will also link you to a... view full answer...
If you ordered adapter # 3026-P with the brake controller, then this is the correct plug for the 2008 Saturn Outlook. On some vehicles, there is an extra wire for illumination of the brake controller, just in case a particular brake controller requires it. As long as the brake controller works correctly when you plug it in, you are good to go. view full answer...
The Roadmaster EZ Base Plate Kit - Removable Arms # 523102-1 is a confirmed fit for 2000-2002 Saturn L Series models. We do not currently have a video of this installation available, but I have attached the installation details that have very specific step by step directions.
If you have questions in the process or if you'd like recommendations to complete your towing setup, let me know. view full answer...
The Curt trailer hitch # C12051 fits all models of the 2007 Saturn Aura including your XR with dual exhaust. Temporarily lowering the exhaust is not required but will make installation of the hitch a whole lot easier. I have included a link to the installation instructions for you.
If you plan on doing any towing with the hitch the recommended ball mount is # C45522 with pin and clip # F-4. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And to add a 4-Way flat connector... view full answer...
Connecting the hot wire of your truck to the 7-way in the bed of your truck will allow the battery in your camper to have a maintenance charge put on it.
If the battery is totally drained it will not recharge it, but it will put a maintenance charge on it while connected. view full answer...
The lower fascia of the vehicle needs to come off when installing the Roadmaster base plate kit part # 154-2 that you referenced but the bumper does not come off. If you check out the attached install instructions link on this page you'll see the entire process walked through. view full answer...
The installation of Draw-Tite # 75528 may be different in the 2014 GMC Acadia than the 2009 Saturn Outlook. Per the instructions:
"Install Central Fasteners – Install fasteners in central receiver bracket.
a. With Bumper Weldnuts – (2) M12 bolts and (2) 1/2” conical washers
b. Without Bumper Weldnuts – (2) 1/2” bolts, (2) conical washers and (2) handle nuts."
You are going to want to use new hardware for your installation and not transfer the hardware from one vehicle to the next. Replacement... view full answer...
The black connector on the end of part # HM47815 will work with your Brake Force controller. However, the white connector on the other end is designed to connect to various Toyota trucks and SUVs and will not plug into your Vue which does not have a connector under the dash for connecting a brake controller. The connector can still be used, but the white connector will need to be cut off.
To install the controller in your Vue, it would need to be hardwired, using our Brake Controller Install... view full answer...
I looked up some videos on line for replacing the rear windshield wiper of your Saturn Vue and found that to remove it from the big plastic housing you will basically just want to pull directly away from the housing. In other words you would pull the wiper away from you and towards the front of the vehicle. In the video it the owner had to pull pretty hard but it will come straight out.
For a replacement rear blade you would want the part # RX30212. view full answer...
The Curt T-Conenctor Vehicle Wiring Harness, part # C56026, for your 2008 Saturn Vue has a circuit protected powered tail light converter (Modulite). This converter powers the trailer lights from a separate wire, with an inline fuse, that is ran to your vehicles battery. If you do not connect that separate wire to the battery you will not be able to get working lights on your trailer.
This harness uses the vehicle wiring as the switch to activate the trailer lights, only requiring about... view full answer...
Go To Results