Overrun brakes are brakes that use the inertia of the trailer against the vehicle braking to activate trailer brakes. For trailer brakes this is most commonly a style known as surge brakes that use hydraulic pressure. Installing a brake controller in your 2018 Range Rover Sport to operate trailer electric brakes would provide the same purpose. A really popular option is the Brake EVN # TK63VR which to install in your vehicle would only require the # 3035-P which plugs in under the dash. view full answer...
For your 2012 Land Rover the correct harness to install the Prodigy P3 part # 90195 is the part # 3035-P that you referenced.
From 2000 to 2008 Land Rover was actually owned by Ford so it's not a huge surprise the vehicle is using an older Ford style connector for the brake controller. view full answer...
The Install of the Rhino Rack Roof Rack with Crossbars, part # RSPT08 on your 2010 Range Rover Sport is pretty straightforward.
The plastic molding that runs down the tracks on either side of the roof is removed, and then trimmed. The roof rack tracks are installed into existing hardware, and the plastic roof molding will install around the tracks once it is trimmed. Purchase of the rack does indeed include installation instructions. view full answer...
When you install the Curt hitch part # C13396 on your 2016 Land Rover Discover Sport the exhaust will not end up lower than before the install. The exhaust will stay in the same place. The picture you have found in the instructions shows the exhaust lowered, but that is not how it would look when installed.
During the install process of the hitch the exhaust will get temporarily lowered so that the hitch can fit into place. It will go back to where it belongs though. view full answer...
As long as the T-One # 118624 wiring isn't touching the heat shield it is in a good place on your 2015 Land Rover Evoque. I have attached an installation video of us installing this wiring kit on a 2013 Evoque that you can reference.
If you plan on using the Draw-Tite Max-Frame Trailer Hitch Receiver # 75227 for towing then to complete a towing setup you also need a ball mount kit. I recommend checking out Ball Mount Kit # 989900 because it includes two ball mounts, one with a 3/4” rise... view full answer...
What you can do is test the wiring of the connector you found with a circuit tester like # PTW2993 to see if there is a stoplight switch circuit on the harness that you could use to install the Prodigy Brake controller part # 90885, but we do not have a plug in harness that will allow for brake controller installation on your vehicle. If not, then you will need to wire the controller up to the wiring of your brake switch like the install instructions for the # ETBC7 indicate.
I would recommend... view full answer...
If the trailer you're wanting to pull has electric brakes, and you want them to operate, you will need a brake controller. Having a dealer-installed 7-way won't eliminate the need for a brake controller.
It sounds as if you've got a good handle on what you need. I'm not sure what '4 wire adapter kit ' you're speaking of consists of, but if it provides a 4-pole trailer connector for your Range Rover, the only other parts you'd need are the # ETBC7 brake controller installation kit you referenced... view full answer...
I wish that would work but Powered Modules like the Tekonsha ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT you are installing need to get power directly from the battery using the included fuse to protect the circuit.
Adding this connector onto an existing circuit could cause it to not receiver adequate power which can cause the connector to stop working, or damage to the module which would now not be covered under warranty due to improper install.
Since going underneath the... view full answer...
Curt 2-inch hitch # C13396 is a confirmed fit on the 2016 Land Rover Discovery Sport without the 5+2 seating feature. This hitch installation will require trimming of both the underbody panel and lower fascia.
There can be some variance in the exact fit of these trim components on the vehicle and this means that there can also be some slight variance in the amount of trimming required.
Curt's instructions, which are linked for you, recommend trimming out a section of the bumper fascia... view full answer...
Yes, I have attached a photo for you that shows the Curt Trailer Hitch Receiver part # C13396 installed on a 2018 Land Rover Discovery Sport as well as a photo that shows the trimming required for both underbody panels. Please note that this hitch is a custom fit for your Discovery so although there is minor trimming of the plastic underbody panels, there is no drilling or major modifications required.
The Curt Trailer Hitch Receiver has a 4,500 lb gross trailer weight and 675 lb tongue... view full answer...
The Bargman Porch/Utility Light with Switch # 3478503 referenced in your question uses a 1141 bulb and will draw 1.4 amps.
This is a nice, compact surface mounted light that will give off a bright enough light to illuminate steps and walkways. It also features a built-in switch on the base for easy operation. It measures 5-15/16 inches long, 3-1/2 inches wide and 2 inches deep. I have attached a short video demonstration on this product so you can get a better look at its appearance. view full answer...
The Titan Disc Brake Kit and BrakeRite Electric-Hydraulic Actuator part # T4843800 comes with two breakaway batteries which are just small batteries responsible for applying the brakes on the trailer in the event it becomes detached from the tow vehicle and are required by law in most states. Therefore, yes you do need to install the breakaway batteries that come with the kit.
Please note, the 6 volt batteries you have on the trailer serve an entirely different purpose and cannot be used... view full answer...
Installation of a hitch like the Curt # C13243 on your 2019 Land Rover Range Rover Sport will not void the warranty. It is not uncommon for a dealer to tell a customer that it will void the warranty. However, consumers are protected under the Magnuson–Moss Warranty Act. This allows aftermarket parts to be installed without warranty issues unless the installation or part caused a problem. The simple act of installing a hitch or other aftermarket part does not void the warranty. view full answer...
We can get you set up with a hitch and wiring harness for your 2017 Land Rover Discovery Sport, and let's go ahead and start with the correct hitch:
- Curt Trailer Hitch Receiver # C13396
I have added a photo that a customer sent in of this hitch installed on their Discovery Sport for you, as well as a cut out from the instructions which show the amount of trimming you'll need to do on the bumper fascia for the receiver. There is also an underbody trim panel which needs to be trimmed... view full answer...
The connector you need to use to install the Tow Ready wiring harness part # 118624 on your 2012 Land Rover Evoque is under the vehicle on the passenger side. Locate the opening to the right of the vehicle muffler. You will reach up into the opening to find the great plug.
Check out the picture I attached to see the plug you are looking for. view full answer...
It sounds like you are hardwiring your Prodigy P2 # 90885 trailer brake controller. If the controller is not powering up the issue would be on the black wire that delivers 12V operating power to the controller via a circuit breaker like # PK54230. The white ground wire also of course must be connected to the battery negative terminal.
You can refer to the linked article on brake controller installation to see the complete wiring scheme. The red wire connects to the cold side of the brake... view full answer...
For a 4-pole trailer connector, you'll need part # 119178KIT. The wiring harness/converter would wire directly into the circuits feeding your taillight assemblies. I've linked you to a video showing the wiring harness being installed on a 2006 Honda Element. The wire colors on your Land Rover would be different, but the testing to determine which wire carries which circuit and the procedure would be very similar for your vehicle.
If you needed a 7-way trailer connector and your trailer... view full answer...
Curt states that a full-sized spare will not fit on your 200 Land Rover LR3 with their hitch part # 13456 installed at the same time. You might consider tracking down a smaller spare so that you can still have a spare with this hitch installed.
We had the chance to install this hitch on a 2006 Land Rover LR3 just like yours. Check out the video I attached that will walk you through the install.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900.... view full answer...
The Curt Spectrum Trailer Brake Controller part # C51170 can be installed on your 2020 Land Rover Discovery. You will need the Universal Installation Kit for Trailer Brake Controller part # ETBC7 and the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit part # 119250KIT.
This will give you the 4-way flat you need to start then allow you to add on the 7-way connector needed to allow for the brake signal wire. The ETBC7 kit also has the wiring... view full answer...
No, the # C59496 trailer wiring harness for the 2008 LR2 by Land Rover will not affect the back-up sensors on your vehicle. No other parts are required to install a 4-Way trailer connection.
This harness is in no way tied into the reverse circuit and only uses the vehicles brake, turn and tail light signals as a switch, the power for the trailer lighting comes from the vehicle battery.
I have posted instructions for the # C59496 below. view full answer...
Go To Results