I checked with Curt and the trailer hitch part # C13421 that you referenced does fit your 2019 Honda Passport and does not require any rear trim panel modifications. Basically the hitch just gets raised into position and from there you just bolt it into place! view full answer...
The Draw-Tite Max-Frame Trailer Hitch # 76290 that fits your 2019 Honda Passport will not interfere with the hands-free liftgate feature. You will likely have to kick your foot to one side of the receiver as opposed to the middle but aside from that the feature would still work.
If you were wanting to do some towing you'd also need trailer wiring like the Curt T-Connector part # C56291 which installs very easily and is very reliable.
If you wanted to do some towing you might be interested... view full answer...
There are no brake controller harnesses available for a 2020 Honda Passport. Brake controllers for this vehicle have to be hardwired in by a local Honda dealer, unless you go with a wireless brake controller.
Because of that I highly recommend the Curt Echo Wireless Trailer Brake Controller # C51180.
I have added a link to a video review as well. view full answer...
It sounds like you're having trouble fitting the ground wire in the back of the 7-way connector on your T-One Vehicle Wiring Harness # 118291. This is larger than the other wires so you need to make sure you are inserting the wire in the correct spot. See the diagram below. The ground wire fits in the larger hole on the right side marked "B."
There is only one orientation for the wires to fit, and once inserted they will lock in place. It should not require a lot of pressure so if you're... view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver # 76290 can be installed on your 2020 Honda Passport by simply raising the hitch into position and tightening the included hardware to the specs listed in the installation instructions. This is one of the easiest and simplest hitch installations and does not require any modifications to the fascia, bumper or any other part of your vehicle.
To complete the trailer towing package on your 2020 Passport, you may consider the following products:
Curt... view full answer...
The Curt Trailer Hitch Receiver # C13421 is actually going to be a pretty easy installation on your 2024 Honda Passport, and it requires zero trimming of the rear fascia on your vehicle to do so. All you need to do is raise the hitch into place and get the hardware snugged up, then go back over them and torque them to the specs in the instructions and you'll be good to go!
I've linked our installation video of this hitch on a 2023 Passport that you can reference for your installation. view full answer...
For your 2021 Honda Passport if you have the 7-way part # 118291 installed you'd have everything you need to install and use the Curt Echo Mobile # C51180 that you referenced. You'd just need to plug in the controller to your 7-way and once it's synced to your phone would be ready to tow. view full answer...
The Curt Trailer Hitch Receiver part # C13421 which is a fit for a 2019 Honda Passport will not require you to remove the rear bumper cover so the installation process is super easy, taking most only around 30 minutes to install. This is a great option with hidden cross tube design that makes for the best overall appearance. In regards to installation, simply raise the hitch into position and tighten down the bolts but that's it. view full answer...
The installation of a trailer hitch receiver on a 2019 Honda Passport is as simple as it gets for any vehicle and does not require any removal of any panels or fascia at all. All that is required to install a trailer hitch is lifting the hitch into place and bolt it in. This process is true of both trailer hitch receivers that fit your '19 Passport, which are:
- Curt Trailer Hitch Receiver # C13421
- Draw-Tite Trailer Hitch Receiver # 76290
Since these hitches are so similar in function... view full answer...
The socket size required to install the Curt Trailer Hitch Receiver part # C13421 on a 2022 Honda Passport 2022 Honda Passport is a 22MM. I have attached a list of all other tools required for the install per Curt.
- Ratchet
- 6" Socket Extension
- 22MM Socket
- Torque Wrench
- Wire Pipe Brush
- Safety Glasses view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver # 76290 is indeed confirmed to fit your 2019 Honda Passport. However, it does state that the hitch may interfere with the Hands-free Liftgate sensors and functionality may be very limited or possibly lost. The same is true for the Curt hitch # C13421 - the only other hitch that fits your Passport.
While we haven't had the chance to install either hitch, we've found that on vehicles with the Hands-free Liftgate feature, sometimes you have to... view full answer...
There's nothing to worry about in this case and you can use the Curt Echo with your 2020 Honda Passport. The reason for the confusion is that brake controllers are not fit guided on our site to particular trailers, since they'll work with any trailer including your Satellite Comet Mini. The reason that your 2020 Honda Passport does not have a signal on the brake signal pin is that all wired brake controllers for this vehicle would need to have it wired by the dealer, but you would still... view full answer...
There isn't a direct plug-in-play brake controller wiring harness for a 2021 Honda Passport but you can use the factory brake controller pigtail to install a controller like the Tekonsha Primus IQ Trailer Brake Controller part # TK90160. It sounds like the wire colors of the factory pigtail aren't matching up with the Tekonsha pigtail therefore you'll have to match by function not color.
Factory Pigtail - Tekonsha Pigtail
Blue to Black
Black to White
Sky Blue to Red
Brown/White to Blue view full answer...
Unplugging the vehicle battery before installing the Curt wiring harness part # C56291 is a precaution. Anytime you make electrical connections on a vehicle there is a risk a short could be created. So while I could see how installing the part # C56291 wouldn't require the battery being disconnected for most people I have to recommend you stick with the manufacturer recommendation. view full answer...
To find an installer for the Draw-Tite Max-Frame Trailer Hitch Receiver # 76290 you can use our "Locate installers near me" link on the product pages. The link will be located below the product images and videos. From there you can enter your zip code or use your current location to find a list of nearby installers.
If you haven't decided on wiring and a brake controller yet, I recommend the Tekonsha T-One Vehicle Wiring Harness # 118291. This will give you the 7-way you need for your... view full answer...
I have a great option for you. The Curt Echo Wireless Trailer Brake Controller # C51180 is going to be as easy of an install as you will get for a brake controller for your 2022 Honda Passport. The reason this will be an easier install is because it is a wireless brake controller, so you will not need to run a wire into the cab of your Passport for the controller.
As with any brake controller, you will need a 7-way connector. If you do not have any trailer wire connector at the back of... view full answer...
Yes, the Curt Trailer Hitch Receiver # C13421 for your 2019 Honda Passport will sit right below the bumper, as shown in the attached photos. It installs ridiculously easily in two steps:
1. Raise hitch into position and secure with the provided M14 bolts and 9/16" conical washers.
NOTE: Weldnut cleaning may be required prior to installation. A nylon tube brush like # 814092 and some spray lubricant is all you need.
2. Torque M14 bolts to specs listed in the included installation instructions.
I've... view full answer...
The best way to unpin the T-One Vehicle Wiring Harness # 118291 is to first disconnect the power and then use a small flathead screwdriver to push the pins from one side while slightly pulling on the wire from the opposite side. You'll need to push and lift the pins to release them from where they are seated. You can also acquire a "wiring terminal removal tool" from your local hardware, home improvement, or auto store to have an easier time as well. Be sure not to pull on the wring too... view full answer...
Neither the Curt # C13421 or the Draw-Tite # 76290 Class III hitches would require any trimming or modification of the vehicle. Both hitches install in the same manner, bolting to the underside of the frame member, and both would appear pretty identical with only the receiver tube and safety chain loop being visible under the rear bumper.
Really the only appreciable difference between the two is that the Draw-Tite # 76290 includes a horizontal bracket welded to the hitch crossbar for... view full answer...
Nope, you do not need to trim the fascia when you install the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 76290.
A few things to take note of though.
Install takes about half an hour.
No drilling required for installation.
Hitch may interfere with the Hands-free Liftgate sensors and functionality may be very limited or possibly lost. view full answer...
Go To Results