Expert Answers about Chrysler

• Brake Controller Installation in 2020 Chrysler Pacifica
• I have good news for you - since you have a factory 7-way in your 2020 Chrysler Pacifica you have a very simple "installation" which will require nothing more than plugging a brake controller wiring adapter into the port under the dash of your Pacifica and then plugging the brake controller into that adapter (essentially, you can think of the adapter as like an extension cord for the brake controller). I really like the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 because it is...
  view full answer...


• Install Picture of Draw Tite Hitch 76046-SK on Chrysler Pacifica
• I attached an install picture for the Draw Tite hitch part # 76046-SK that you referenced on a similar 2020 Chrysler Pacifica for you to check out. It's not a hybrid model in the picture but it would look the same on your hybrid model.
  view full answer...


• Does The Heat Shield Need To Be Trimmed Or Can It Be Removed When Installing etrailer # e98903
• On your 2017 Chrysler Pacifica Touring L model, you can simply remove the underbody panel as you stated when installing the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e98903. I don't recommend leaving the panel off completely because it is a heat shield to protect other components. You can see in the video that we trim it slightly more than is needed to make the install easier. Removing more than what we did in the video is not recommended.
  view full answer...


• How to Find Reverse Light Circuit on 2018 Chrysler Pacifica
• You're on the right track; this is the correct adapter, and the best place to look for the reverse light circuit when installing the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 is on the tail light assemblies on your 2018 Chrysler Pacifica. When installing this adapter, you may need to have a friend activate each function and test the wires using a circuit tester like the # PTW2992 to get the correct wire to tap into.
  view full answer...


• Furrion RV Tankless Water Heater Operation Capabilities
• The Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 16" x 16" Door Item # FR98SR vortex system mixes cold and hot water together to prevent scalding. This unit will put out 2.4gal/minute of hot water so someone could take a shower while you're washing the dishes and you still shouldn't have a cold spike.
  view full answer...


• Why Does Curt T-Connector C56333 for a 2009 Chrysler Town and Country Connect to Battery
• The Curt T-Connector you referenced, part # C56333 receives the signals through its T-connection with the tail light assemblies of your Town and Country, but draws the actual voltage to power the trailer lamps directly from the battery. This is done for a few reasons. First and foremost, if the aftermarket trailer wiring harness manufacturers determine that the OE vehicle wiring is incapable of handling the extra amperage of the trailer lights being drawn through it, they will specify...
  view full answer...


• Torque Rating for Class III 75522 for 2004 Chrysler Pacifica
• We don't publish the torque ratings for the fasteners, because the hitch manufacturers can change them. If you look at the bottom of page 2 of the instructions (see provided link), you'll see the torque rating for both the 1/2 inch and the M12 fasteners. The links pull the instructions directly from the manufacturer's websites, so they're always current. I'll also link you to an install video for the hitch. If you'll be using the hitch for towing, you might also be interested in the following...
  view full answer...


• Can Multi-Displacement System On 2005 Chrysler 300C be Turned Off With Superchips Tuner
• With the use of the Superchips Flashpaq Performance Tuner, part # SU3845, you are not able to turn off the MDS in your Chrysler 300C. To be CARB(California Air Resources Board) or also known as Clean Air Agency, compliant, the use of this tuner does not allow you to change the emissions components like the MDS on your vehicle.
  view full answer...


• Towing Chrysler PT Cruiser Convertible with RoadMaster Tow Dolly with Electric Brakes
• As long as you have hitch at the rear of the vehicle that has towing capacities to tow your vehicle and a drawbar with similar weight capacities that has a 2 inch ball you have everything you would need to use a RoadMaster Tow Dolly with Electric Brakes, part # RM-2050-1. This tow dolly comes with electric brakes, safety cables, adjustable axle and ramps, and adjustable wheel nets. Once you assemble the tow dolly you will just need to hitch up the tow dolly to the ball of the drawbar and...
  view full answer...


• Stabilization Strap Use for a CURT Trailer Hitch and Cargo Carrier on a 2004 Chrysler PT Cruiser
• For CURT Class I and II trailer hitches, when you have a non-trailer load such as a bike rack or in this case a cargo carrier, you can use the stabilization strap, # 18050. One end you will loop around the near edge of your carrier. The other end has a hook that will fit at the top of the rear hatch in the space between the roof and the hatch on your 2004 Chrysler PT Cruiser. The strap needs to be snug but be careful not to over tighten the strap.
  view full answer...


• Mighty Cord RV Power Cord Adapter Usage Instructions
• The Mighty Cord RV Power Cord Adapter - 50 Amp Female to 30 Amp Male - 12" Long Item # A10-3050FHVP is for hooking up to the male 50 amp cable coming from an RV and plugging into a 30 amp female outlet in the power pedestal at your destination.
  view full answer...


• Installing Brake Controller on 2005 Chrysler Pacifica
• The Chrysler Pacifica was not equipped with the brake controller connector under the dash. It sounds as if you already have quite a bit of work done already. However, I do have one note on what you have already completed. On your 12-volt power supply wire that you have ran from the battery to the trailer connector, I would suggest installing a 40-amp inline circuit breaker like part # 9510. The breaker is typically mounted to the inside of a fender or other convenient mounting location...
  view full answer...


• Requirements to Tow Mobility Scooter Behind 2001 Chrysler PT Cruiser.
• Based on my research, you can tow a trailer with your 2001 Chrysler PT Cruiser, but there are several warranty limitations. The owner's manual I found states to never exceed the gross axle weight rating of your vehicle because of the added weight of the trailer hitch's tongue weight or cargo weight. In order to comply with the vehicle's warranty, the following requirements must be met: -The max. frontal area of the trailer cannot exceed 20 sq. ft. -If your vehicle has a manual transaxle,...
  view full answer...


• Wiring Options for a 2009 Chrysler Aspen Towing a Boat Trailer with a 5-Way Flat Trailer Connection
• Yes, the Tow Ready Custom Fit Vehicle Wiring for the 2009 Aspen by Chrysler, item # 118390, is the correct wiring harness for your Aspen and you will need one other item to complete the wiring to lockout the brakes on your boat trailer surge coupler. You can go one of three ways for this wiring. The easiest way in my mind is to install the # 118390 T-One and then splice the 5-Flat Vehicle End 5' Wiring Harness, item # HM37908, to the 4 like wires left by removing the 4-way vehicle end...
  view full answer...


• Is it Necessary to Connect the Power Wire to the Battery on a 2013 Chrysler 200
• Yes, it is necessary to run the lead from the Wiring # C56211 that runs from the battery to the trailer connector. This wire carries the voltage necessary to power the trailer lamps. The wires that are connected to the tail light assemblies tell the converter that the vehicle tail lights, turn signals or brake lights are operating, but do not provide the voltage for the lamps. Vehicle manufactures have determined that the circuits feeding the tail light assemblies on the vehicle cannot...
  view full answer...


• Items Needed to Install Brake Controller on 2005 Chrysler Pacifica
• Because the 2005 Pacifica is not pre-wired for a brake controller, the controller would need to be hard wired using a Brake Controller Install Kit # ETBC7. There is not a wiring adapter available. Although the install kit contains everything needed to install the brake controller, the vehicle will need a functional 4-pole trailer connector, part # C55530 if it does not already have one. The adapter included in the kit will convert the 4-pole to a 7-way trailer connector. Once the adapter...
  view full answer...


• Do Hitches of 2021 Chrysler Pacifica Hybrid Install Differently
• There is a small difference in installing the etrailer.com Trailer Hitch Receiver part # e98903 on a Hybrid compared to a non-hybrid 2021 Chrysler Pacifica. There is an emissions canister on the driver side frame rail that needs to be relocated temporarily to install the hitch. If you check out the attached install instructions link for this hitch on this page on step 5 you'll see this outlined.
  view full answer...


• Warranty Implications of Installing Curt Class III Receiver Hitch C13383 on 2020 Chrysler Pacifica
• The answer to your first question can get pretty involved, but in summary purchasers of aftermarket vehicle products are protected by the Magnussen-Moss Warranty Act which states that installing a hitch won't void a vehicle warranty unless the vehicle manufacturer can prove that the aftermarket part directly caused the failure. You can install the Curt Class III # C13383 hitch with no worries. Curt tells me that they've received no report of the hitch installation having any effect on...
  view full answer...


• Is Trimming Required To Install Curt Trailer Hitch C29UR On 2018 Chrysler Pacifica Hybrid?
• That is correct. To install the Curt Trailer Hitch Receiver # C29UR on your 2018 Chrysler Pacifica Hybrid you will need to remove two the exhaust hangers from the rubber isolators, and support the exhaust to make sure it does not get damaged. Next you will remove the heat shield you mentioned, and will need to trim it according to the included diagram. Once the hitch is in place, you will reinstall the heat shield, and the reinstall the exhaust into the rubber isolators. You will also...
  view full answer...


• How to Identify Correct Brake Light Switch Wire for Brake Controller Installation in 2017 Pacifica
• The cold side of a brake light switch is used as the trigger signal to activate a trailer brake controller like the Prodigy P2 # 90885. The controller installation kit you purchased, part # ETBC7, includes a probe-style circuit tester that allows you to determine which of the wires at the brake light switch is connected the to cold side of the switch. The correct vehicle wire to connect to the RED wire on the controller is the one that goes hot ONLY when the brake pedal is pressed, and...
  view full answer...