Tekonsha Prodigy P2 trailer brake controller, # 90885, connects to a fused power source directly to the battery and not an ignition source. This means the controller draws power even with the key off. However, it goes into a kind of sleep mode after about 15 minutes of inactivity and will not draw much power from the vehicle battery.
If you will be parking the vehicle for an extended period of time, you can also unplug the connector at the back of the unit, which will immediately power... view full answer...
We do have a video of the Draw-Tite hitch you purchased, part # 24943, being installed onto a 2017 Chevy Cruze. I've linked it to this page for you, as well as the install details.
Despite the difference in model years the installation process on the 2017 shown in the video is basically the same as your 2018. view full answer...
When carrying just a single bike with the Swagman XTC 2 part # S64670 you would want to load it in the position closest to the vehicle. This decreases the leverage the rack has on the bike rack. Also, if you are carrying 2 bikes you would want to load the heaviest bike closest to the vehicle for the same reason. view full answer...
The Curt wiring harness you referenced, part # C56214, does require a 12V power connection to your vehicle battery in order to operate your trailer's lights. However, if this power wire is not run to the battery, the vehicle's tail lights should still behave normally since the harness plugs in on the vehicle in parallel. The harness will not be able to provide power to a trailer's lights without the 12V power feed.
I have linked you to an article that shows how to route that power wire... view full answer...
If you do not run the wire to the battery when installing your harness, the tail lights on your 2014 Chevrolet Cruze should still work. The harness will not have power so any trailer you would connect would not have the required 12 Volt power.
Should you decide to attach the wire at a later date, I have attached a link to a helpful article that explains how to run the power wire you can check out. There should be instructions included with the wiring harness that will show how to run the... view full answer...
Curt T-Connector 4-Pole Vehicle Wiring Harness # C56319 will install the same way in all vehicles with which it is compatible. This wiring harness works with both 2016 and 2017 Chevy Cruze model years.
The installation consists of plugging in the grey connectors at the back of the car's taillight assemblies, attaching the white ground wire ring terminal to a clean metal surface and connecting the included black power wire at the battery positive terminal and at the harness's control module.... view full answer...
You actually want the steering wheel to lock on the vehicle that is getting towed on a tow dolly so what you have now would work great since yours locks. If the front wheels didn't lock there would be damage to the side of the vehicle as it turns since the dolly would hit it.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies... view full answer...
Tow Ready has determined that the 2012 Chevy Cruz has a wiring system that requires a powered converter, # 118508. The power wire that connects to the battery provides the power to the trailer lights. This protects the vehicles sensitive wiring and electrical system from damage.
The Cruz also uses a 3 wire system and most trailers use a 2 wire system. That is why a converter is needed. The vehicle has separate turn signals and brake lights, a trailer has combined turn signals and brake... view full answer...
I want to start by thanking you again for ordering with etrailer.com. We appreciate your business.
As for the 4-way connector on your 2015 Chevrolet Cruze, as long as there is nothing around the grommet that would prevent you from drilling the hole larger, the 4-way can be routed to the underneath of the vehicle for a cleaner look. We do offer no-drill mounting brackets, # 18140 for short and # C57202 for long, which are used with 4-way mounting bracket, # 18144, to secure your connector.
Since... view full answer...
The power wire for harness # 118508 can't connect to the fuse box. It has to go to the battery on your 2012 Chevy Cruze. You can route the wire to the battery any way you want. Along the frame, through the frame, through the interior of the vehicle. It depends on what you want to do.
There are other wiring harnesses under the vehicle that you would secure the power wire to. So its not like it is just hanging there. And of course you would want to avoid exhaust and suspension parts; anything... view full answer...
Typically when a 5-Way connector is on a vehicle, like your 2011 Chevy Cruze, it carries the reverse light circuit. Since this isn't usually needed for towing a trailer you should just be able to plug the 4-Way connector from your trailer into the 5-Way on your Cruze.
In the case that the 5th pin is for the brake lights you can simply install the Roadmaster Converter # RM-732 to combine your brake and turn signals and retain your 5-Way connector. You can use a circuit tester like part... view full answer...
The # C56175 does not feature a powered converter box, so no power wire is present on the harness. If you have a 2011 Chevrolet Cruze, however, I would actually recommend using the # 118508 harness instead.
The # 118508 does have a power wire, but this is actually a feature that protects your vehicle's wiring system and puts less strain on it, since power is pulled directly from the battery instead of your tail light circuits. In addition to protecting the vehicle's wiring better,... view full answer...
Yes, we using the Roadmaster Tow Dolly with Electric Brakes - 4,250 lbs item # RM-2050-1 the towed vehicle's steering must be locked. Here is the step in the instructions straight from the owner's manual:
15. The towed vehicle’s steering wheel must be locked or otherwise secured when towing. Failure to lock the steering wheel will allow the towed vehicle to pivot on the bed, causing it to hit the fender and wheel assembly of the dolly. Severe damage will result to both vehicles. view full answer...
There are two Class I trailer hitch receivers with a 2,000 pound towing capacity available for your 2016 Chevrolet Cruze. The Draw-Tite Sport Frame # 24943 and the Curt # C11439. If you're looking for a hitch I suggest the Draw-Tite because it does not require the use of a stabilization strap, # 18050, for non-trailer loads like the Curt does.
If you only need the hardware to install either hitch the part is # RHK. You will need to put in the part number and manufacturer of the hitch... view full answer...
The size of the hardware used to install the Draw-Tite Sportframe Trailer Hitch Receiver # 24882 on a 2014 Chevy Cruze is 7/16"-14 x 1-1/4" as you can see in the linked installation instructions. view full answer...
The Curt wiring harness for the 2012 Chevy Cruze, # C56214, does require a direct connection to the vehicle battery. The unit receives power needed from the vehicle battery. I have included a link to the installation instructions for you to view. view full answer...
Often times there are different ways to modify the heat shield of a vehicle when installing a hitch like the Curt # C11439 on your 2018. Typically our manufacturers recommend the simplest way to modify it but going a different route can work well. We can't guarantee that what you wanted to do would work but worse case scenario you could try it and then go the way Curt recommends and for sure that would work. view full answer...
I've linked the install details to the Roadmaster EZ4 base plate kit that fits your 2017 Chevy Cruze, part # RM-523190-4. They're also on the product page.
Certain models of the Cruze do require that the fascia, spoiler, grille, or air dam be trimmed for the install. view full answer...
You will need to adjust the Fit Dial on the Thule Gateway Pro 2 Bike Rack # TH88VR to #7 when installing it on your 2017 Chevy Cruze. view full answer...
To install Curt trailer hitch # C11282, you will not need to make any modifications to the bumper or rear fascia. You will need to temporarily lower the exhaust by simply removing the affected area off of its hangers while supporting the pipes with a strap. And there is a heat shield that has to be modified as well but it is under the vehicle and not visible.
Once installed the receiver will be below the rear fascia. I have included a link to a video showing installation of the hitch... view full answer...
Go To Results