If the Workhorse chassis on your 2003 Tiffin Allegro is a P30, P32, or P3500 then you will want to use the Roadmaster Reflex Steering Stabilizer # RM-RSSCP30, but if you have a W20 or W22 you will want the Roadmaster Reflex Steering Stabilizer # RM-RBK13-RSSA instead.
Let me know if you have a different chassis and I can help you find a different solution for a better ride. view full answer...
Yes, you can use the Roadmaster Magnetic Tow Lights, # RM-2120 with a 2013 Tiffin Allegro Breeze Motorhome. These removable tow lights make it easy to add running lights, brake lights, and turn signals to your towed vehicle. As you will see in the attached video, when you install them, you decide which type of connector you will use and purchase the appropriate adapter.
Once they are initally set-up, you can simply plug the connector into the 7-way on your 2013 Tiffin Allegro Breeze motorhome... view full answer...
There's too many variables to consider when rerouting propane so there isn't an all-in-one type of kit. Typically if you're routing permanent lines it's recommended to use a copper hard line instead of a hose so you would need a tee like # 37207-30135 to be able to connect the line. You would need a 1/4" male inverted flare fitting to whatever fitting you end up putting on the copper line.
Typically a 3/8" swivel flare fitting is used on copper lines so you could get a 1/4" male inverted... view full answer...
I tried looking up info on your model light but I couldn't find anything online. The Gustafson RV Puck Light # 277-000343 has an overall diameter of 3-1/2" and it is 1-1/4" tall. The base dimensions are 2-1/8" diameter x 3/4" tall while the 3 mounting holes are spaced 2-1/4" apart on center.
If you remove your current light and it has the same specs then this light will work great as a replacement! Simply wire the black wire to 12V power and then the white wire to ground and you are good... view full answer...
Furrion Chill Replacement RV Air Conditioner for Coleman Setup # FR42PV is 13-5/8" tall and the conversion brackets are on the inside of the cutout so the total height above the camper would be 13-5/8". The Furrion rooftop units have condensation holes as you can see in the attached picture that will allow condensation to leak out onto the roof and unfortunately will not work with your Coleman condensate pump. view full answer...
Yes, the Glantastic LED RV Puck Light - 197 Lumens - Semi-Recessed - Frosted Plastic Lens - Warm white, part # 328-K-58L34P9, are 12V lights that use 3W of power. While I do not know how bright the lights were that you are replacing, but it is probably safe to say that these lights will be brighter while drawing less current.
I have included a video demo link below. view full answer...
We do not have the original full step for your 2013 Tiffin Allegro Bus 43QGP, but is a Lippert step, part # 5041647. We do offer a replacement, the Replacement Steps, Motor, and Control for Kwikee RV Electric Steps - 27 Series - 29" Wide, part # LC375632, is a direct replacement. If you prefer a non-scissor step, we do have the Replacement Steps, Motor, and Control for Kwikee RV Electric Steps - 47 Series - 26-5/16" Wide, part # LC427247. This is a slide-out 2 step option.
I have included... view full answer...
The correct base plate kit you will need to use the Blue Ox Aventa II Tow Bar part BX7335 on your 2017 Ram 1500 is the Blue Ox Base Plate Kit part # BLU74FR if you have the Rebel, Big Horn, Laramie, or Laramie Longhorn; part # BX1986 if you have the Tradesman or Limited; and part # BX2409 if you have the Sport or Express edition. I have attached an install video on each of these kits for you.
The correct flat-tow wiring harness I recommend for you is the Roadmaster Diode 7-Wire to 6-Wire... view full answer...
Rear poly bushing kit # RM-4139-125 is indeed a fit for your 2011 Tiffin Allegro built on a Ford F-550 chassis. Roadmaster notes that some of the endlink parts may not be used in the installation and that the fit assumes a 1-1/2 inch OEM bar.
Your bar at 1-27/64 inches (1.42 inches) is very close but ultimately too small for a proper fit and you will need a different option.
The other option is # RM-4139-300 for a 1-3/8 inch diameter bar. This is actually closer to the 1.42 inch bar... view full answer...
Yep, you can mount a Blue Ox tow bar like the Blue Ox Avail # BX7420 to Roadmaster direct-connect base plates, and all you need is a simple adapter, which is the following part number:
- Roadmaster Adapter Kit for Blue Ox Motorhome Mounted Tow Bars # RO64FR view full answer...
I was able to verify with Roadmaster for you the correct fit for your 2020 Tiffin Allegro Open Road 36UA motorhome, which is the following:
- Roadmaster Exact Center Steering Stabilizer # RM62RR
The # RM62RR consists of the stabilizer and custom mounting brackets that fit your Tiffin motorhome; this will give you much better overall responsiveness when steering your rig for a more comfortable ride. view full answer...
The width of the MORryde Sliding Tray for RV Cargo Compartment - 90" x 33" - 800lbs - 2 Way # MR46FR is 32.74". They list on their spreadsheet 33" but also state that actual measurements are 1/4" smaller to to fit in the width opening it's listed under. The width is including the sliding brackets and the handle so your 33" opening will work. view full answer...
The Front SumoSprings Rebel Custom Helper Springs # SSF-173-40-2 are the correct Springs for your 2018 Tiffin Open Road Alegro 36UA on the Ford F53 GVWR 26,000lb chassis. These have a 3,000lb capacity to assist your suspension in supporting the additional weight on your chassis and will help to reduce road shock and body roll.
The Rear SumoSprings Maxim Custom Helper Springs # SSR-183-54-1 are your correct rear springs for your Tiffin. They have a 7,000lb weight capacity for supporting... view full answer...
The Curt Echo wireless brake controller, part # C51180 isn't vehicle specific, so it'll work just fine with your Tiffin Phaeton motorhome. When you install the 7-way, you'll want to make sure that the pin in the 1:00 position is putting out a constant 12-volts. It should be connected to the positive battery terminal with an inline # 9510 40A circuit breaker.
The Curt Echo would use your smartphone (Apple 8.0+ or Android 4.4+) to control it. The controller has a 50 foot wireless range,... view full answer...
I called Air Lift to confirm, and you are correct in that the LoadLifter 5000 Ultimate Air Springs, part # AL88240, are not compatible with your 24,000-lb chassis.
We do, however, have springs that are compatible. They are the SumoSprings Rebel Custom Helper Springs, part # SSF-173-40-2. These jounce-style springs are much easier to install and maintain than air springs, and they react appropriately to different loads (rather than the air springs needing manual adjustment when under different... view full answer...
Modifying the SnapPadEQ Round Jack Pads , # SP64FR4, by trimming is not something that has been tested. Because these function by pressure that type of modification may have negative effect. These are not only sold in sets but individually as well for replacement needs. I suggest buying one and testing its fit, # SP64FR. view full answer...
It sounds like you have Fan-Tastic Vent Roof Vent 801250, which has reverse flow, a 3-speed fan and no rain detector. If this is your fan you need the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00, which replaces the bow-tie bracket, motor, and blade for your vent. view full answer...
I contacted the manufacturer in regards to your question, they informed me that the Rear View Safety Color Monitor # RVS-6139Q uses cameras with 5 pin connectors, so your Mito cameras with 6-pins would not work unless you wanted to use the Rear View Safety Splice Kit # RVS-SPK01 to splice your cameras in.
They did strongly recommend that their cameras, like the Rear View Safety Backup Camera # RVS-771, Rear View Safety Side Camera - Driver's Side # RVS-775L and Rear View Safety Side Camera... view full answer...
The correct SumoSprings Custom Help Springs for a 2018 Tiffin Open Road Allegro 32SA is part # SSR-183-54-1 for the rear and part # SSF-173-40-2 for the front. view full answer...
The overall diameter for 295/80R22.5 would be just over 41" so I recommend the SnapRing TireSavers Tire Covers - 40" to 42" Diameter - Black Vinyl # ST7005BK. These tire covers have an internal ring that allows them to easily expand to fit over your tires and "snap" right back for a snug fit.
I've attached a short video below where I'll walk you through just how easy these are to use. view full answer...
Go To Results