Expert Answers about Forest River LED Strip Lights
- Solution to Add LED Strip to Solera 3000 Series Awning Roller
- For an LED strip on the roller you could add something like the Optronics Flexible LED Light Strip - Weatherproof - White - 17' Long # UCL90CB. However, you will need to figure out how to run power to the strip and account for the rolling/unrolling with the power wire.
There is the option of using the Solera Power Awning Idler Head w/ LED Upgrade # LC334785. However, this is designed to add lights to the inside of the tube, not on it. It also does not match your current Regal idler head...
view full answer... - Recommended Awning Mounting Brackets
- We have two options to attach awning fabric to the side of your RV. They are the 8' Solera Awning Rail Extrusion in white item # LC715216 and in black item # LC715217. Additionally, we have a few brackets for slide out awnings like item # LC795354 but they are specific to Solera models. Either way I would need to know what model of awning you have to confirm the right brackets for you. If you could email me this information directly or comment below I would be happy to help.
As far as...
view full answer... - Light Strip and Wiring Parts Needed to Add Reverse Light Strip to Trailer
- Thanks for reaching out, Steve!
For a 60" light strip we have the Premium Slim LED Strip Light # TN38ZR which is weatherproof and rated for 3,638 Lumens. You'll need the Deka Heat Shrink Butt Connectors # DW05744-10 to make your connections and you'll also need to tap into the reverse light function on your tow vehicle with the wiring kit # 20036 as well as change your trailer connector to a 5-Way with part # HM37918 so everything will match up.
view full answer... - Which Pin Is Used for Running Lights on the Curt Auxiliary LED Indicator Lights 4-Way Connector
- Hey Richard!
The running light function will be the wire that was closest to the ground pin on the Curt Auxiliary LED Indicator Lights # C53201 4-way connector. I haven't stripped back the cover on this kit before so I don't have any hands-on experience with what you're doing, but I can say that the ground pin is the covered one and then the next one next to it is the one you want to connect your registration plate light to.
Attached is a photo of the vehicle side pin out for a 4-way...
view full answer... - Will The MORryde Motion Activated Light Strips Fit on Lippert Steps?
- Yes, the MORryde Motion Activated Light Strips # MR42AR can also be used on Lippert Steps. You simply need to ensure your steps are magnetic where you plan to set the light as it is held in place with a magnet and requires no drilling or other modification.
view full answer... - Can the Curt Custom Tail Light Wiring Kit Be Used With LED Lights
- The Curt Custom Tail Light Wiring Kit for Towed Vehicles # C96JR can be used with your LEDs, the only caveat is that if your Jeep has ParkSense proximity sensors then you'd need to use the Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles # RM-152-98146-7 instead.
view full answer... - How to Keep LED Turn Signal Lights on Toolbox From Flashing with Brake Pedal Pressed
- Hi Richard!
It sounds like you're needing to install the Load Resistor Kit for LED Turn Signals # DI34ZR on the turn signals you've installed on your toolbox.
Since LEDs don't require as much power as incandescent bulbs, sometimes we see some power "leak through" and cause the LED lights to flash like what you're experiencing. The resistor kit makes the LEDs "look" like incandescent lights to your wiring system so this kind of thing doesn't happen.
view full answer... - Smart Diodes Needed For Flat Towing A 2021 Chevy Spark With Incandescent Tail Lights
- Hi Mike,
The Roadmaster Smart Diode # RO54FR is designed for use specifically with LED tail lights so if your towed vehicle has incandescent bulbs you'll need part # RO34FR instead. These should properly read your motorhome and vehicle traffic signals to display the signals correctly through your incandescent tail lights.
view full answer... - Do You Offer a 6" LED Strobe Light Which Can Be Surface Mounted?
- The LED Dual Row Strobe Light # 3378891701 is the closest in size to the LED Strobe Light # 337SL65CO you found, but in a surface mount. This light is 5-1/4" x 2" compared to the light you found of 6-1/2" x 2-1/4".
view full answer... - Load Resistor to Prevent ARC LED Bulb From Hyperflashing on 2020 F-250
- Hey Christopher, thanks for reaching out!
The WT21W LED Bulbs # ARC79GR you're looking at do not have a built-in resistor. For that you'll need the ARC Lighting Load Resistor for LED Lights # ARC22VR to prevent that hyperflashing.
view full answer... - Does Vista LED Light Kit LC24PJ Have Adhesive Backing
- Yes Anne, there is an adhesive backing on the Vista LED light kit part # LC24PJ.
view full answer... - Can Gustafson RV LED Puck Light 277-000488 be Used in RV Bathroom
- Hey Tom, so the RV puck light part # 277-000488 could be used to provide additional lighting to your RV shower but you would need to make sure you put it in a location where it won't get sprayed with water from the shower. It can handle the higher humidity of a bathroom application but not water directed on it.
view full answer... - Does Boat Trailer with LED Reverse Lights Need Load Resistors
- The load resistors part # DI34ZR that you referenced are not submersible but based on your application it does not seem like you need to install load resistors. The reverse light circuit of trailer wiring shouldn't require additional resistance to activate.
view full answer... - 4-Way Flat Wiring Harness and Submersible Tail Lights For a Boat Trailer Over 80" Wide
- The 25 Ft 4-Way Trailer Wiring Harness # A25W2GWB you found is going to have the 3 wires which run down each side of the trailer. One wire on each side is going to be a ground wire(white), the 2nd wire(brown) is going to be for the running lights and side marker/clearance lights and the 3rd wire(green or yellow) is going to be for the turn signal/brake lights for each side of the trailer. The Optronics LED Combination Trailer Tail Lights # TLL160RK are submersible and the correct size needed...
view full answer... - Parts Needed to Install 7-Way/Brake Controller 2021 Ford Bronco with LED Taillights
- We have a way to install a 7-way on your 2021 Ford Bronco that does not have LED taillights but you'll have to first start with a 4-way like the part # C87BR and then convert it to a 7-way with the part # ETBC7 which also comes with the components needed to hardwire in a brake controller like the Prodigy P2 part # 90885.
This is a universal style install that will require hardwiring as we do not have a custom fit wiring solution at this time.
view full answer... - Can Curt Trailer Wiring Harness # C59DR work with Trailer LED Taillights
- Hey Ray, yes the Curt trailer wiring harness part # C59DR does work with trailer LED taillights.
view full answer... - Replacement Tail Light For 5X10LGW2K Trailer
- Hi Daniel,
I was able to Google the correct tail lights for your trailer and while we don't have a ramp, here is what you need for tail lights. I know you said right tail light, but 'll go ahead and list out both the driver and passenger side options in case you need both at some point.
- Passenger Side: LED Trailer Combination Tail Light # STL38RB
- Driver Side: LED Trailer Combination Tail Light # STL39RB
view full answer... - Looking For Stop/Turn/Tail Lights With A 90 Degree Pigtail
- Hello Derek. I see that you were looking at the Optronics Fleet LED Trailer Tail Lights # TLL12RK. We do have a 90 degree pigtail for these lights with part # A47PB which uses the same PL-3 prong plug. Keep in mind these Optronics lights are 7-9/16" long x 3-5/16" tall x 1-3/4" thick so as long as this is the appropriate size for your trailer, this will be a great choice. The optronics LEDs are very well made and will likely last the lifetime of the trailer.
view full answer... - Do Vehicle Taillights Need to Function If Vehicle is Towed with Tow Dolly
- Generally, you don't need additional lighting when using a tow dolly that already has lights. However, it's not a bad idea to check with the local laws in the states you'll be traveling in. If you do need to have lights on the vehicle you could use the magnetic LED tow light kit part # TLL21RK and to add a 4-way to your tow vehicle's wiring you would want the part # 18252 which would wire into the current trailer wiring.
view full answer... - What Lighting Functions Does the GearSpace 34 Enclosed Cargo Carrier Have?
- The GearSpace 34 Enclosed Cargo Carrier item # HGK819 does not have backup lights. It has two LED tail lights, an illuminated license plate bracket, and reflectors. The LEDs have stop, turn, and the standard illuminated tail light function.
The lights are powered and controlled by a standard 4-flat connector. To add a trailer connector to your 5th wheel trailer, I recommend the 4-Pole Hardwire Kit with Circuit Tester item # 18252. This kit comes with a circuit tester which you'll need...
view full answer...
Go To Results