The connector that the Hopkins harness, part # HM41245 plugs into is located in the jack storage compartment. The jack storage compartment is located in the cargo area of the vehicle on the driver's side.
Locate the white connector and remove the tape covering the end of it and plug the Hopkins harness into the connector.
To see the install instructions, click on the provided link. view full answer...
You will need the Roadmaster Standard Base Plate Kit, item # 118-1, or the Roadmaster XL Base Plate Kit, item # 118-3, for your 1995 Geo Tracker.
If you will not be towing the vehicle often I would recommend the standard base plate kit but if you are planning on towing more often then I would recommend the XL base plates with one of the nicer tow bars for convenience.
Along with the base plate kit you will need a tow bar and wiring for the towed vehicles taillights. With the Standard... view full answer...
Yes, the connection point to add trailer wiring harness # 118372 should be the same on a 1998 and 1999 Chevy Tracker. The connection point is located in the inside of the drivers side tire jack compartment. The plug where you will connect the trailer wiring is just forward of the tire jack compartment. I have included a link to the installation details for you. view full answer...
The Custom Mounting Bracket Kit for SnowBear Hydraulic and Winter Wolf Snowplows # SB397-050 does have mounting holes, but is a confirmed fit for your 1992 Geo Tracker. view full answer...
The Bestop Duster Deck Cover for Geo, Suzuki 1995-1998 - Black Denim # B9002915 does require the retainer clips for installation. I reached out to my contact at Bestop and they said you will need those clips and they do not have a solution other than to replace them and unfortunately we do not have them. They are easy to find and will make this cover an easy installation as you can see from the attached instructions. view full answer...
Yes. The Blue Ox Aventa II tow bar will work with the Blue Ox Base Plates # BX3503 without any issues on your 1992 Geo Tracker. You may also need a lighting solution for this new setup on your Tracker, so if you need lights also, the Roadmaster Standard Magnetic Towing Lights # RM-2120 are an easy to install choice that won't break the bank.
A complete flat towing setup will consist of a tow bar, base plates, safety cables, tow bar lighting, supplemental braking and possibly a high/low... view full answer...
Yes, Roadmaster base plates # 118-3 will fit your 1992 Geo Tracker 2-door 4x4. For a compatible tow bar I recommend the Falcon 2 # RM-520. I have linked a video review of this tow bar for you. For safety cables I recommend # RM-643. The coiled design helps keep the cables off of the ground.
For lighting you can use a simple kit such as # RM-2120. this kit bypasses the Tracker wiring so you won't have to splice into the tail light wiring.
You may also need a high/low adapter to keep the... view full answer...
As a general rule of thumb, trailer tires should be replaced every 6 to 8 years regardless of wear. Even though an older tire might appear to have plenty of tread left on it, dry rot and cracking can cause tire failure.
The mating surface behind the bolt holes should be flat, and should mate perfectly with the face of your hubs.
I would definitely replace the tires before using the trailer again. If the wheels are showing signs of corrosion, I would also recommend replacing them with... view full answer...
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.
I also attached a link to all of our help articles on flat towing lighting as well. view full answer...
The correct mount kit for your 1992 Geo Tracker to use your Snowbear Plow part # SB324-167 is the part # SB397-050 that you referenced. This kit is custom fit for your vehicle and is designed to work with the Winter Wolf as well. view full answer...
The # C56175 would be installed on your Tracker if you wanted to tow a trailer with it, but it will not work for towing the Tracker behind a motorhome.
To wire the vehicle for flat towing there are several available systems, as you can see in the article I have linked you to. A magnetic towing light kit like # RM-2120 would be an easy to use, easy to install alternative. If you would prefer a permanently-wired alternative, the article outlines how to determine which choice is best for... view full answer...
For your 1993 Geo Tracker the only trailer wiring harness I can recommend for you is a universal install harness like the part # 119178KIT that has been confirmed as a fit.
The # C55372 that you referenced would not work for your vehicle. view full answer...
In order to attach the Tow Ready Tow Bar, # 63180, to your Roadmaster base plates, you will need the Roadmaster Base Plate to Tow Ready Tow Bar Adapter, # RM-025. This will allow the two different parts to work together.
The Roadmaster Quick Disconnect Tow Bar Base Assembly, # 910021-00, is for Roadmaster tow bars so it should not be needed, just the adapter and tow bar listed above. I have included a link to the installation details for the tow bar for you.
Keep in mind that the Tow... view full answer...
You are correct that the SportRack # SR1002 does require a hard top roof. Your best bet is to go with a trailer hitch like the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 11128. Then you can use a lightweight trailer like the Yakima Rack and Roll Trailer # Y08106. I have included a video review of this roof rack on wheels for you to check out.
To complete your towing package, you will want the following:
Drawbar # 3593
Wiring kit # 119178KIT
1-7/8" hitch ball # 19256
2"... view full answer...
I may have a solution for you, however the Bestop Duster Deck Cover # B9002915 referenced in your question is not confirmed to fit your 1993 Geo Tracker. It looks like there are enough differences between the 1993 and 1995 model Tracker that this particular cover is not compatible.
For your 1993 Geo Tracker we do have the Bestop Strapless Bikini # B5257015 which is confirmed to fit and will work well. This will replace the factory-original top on the vehicle to provide a canopy over the... view full answer...
The Curt Trailer Hitch Receiver part # 11128 is indeed a confirmed fit for a 1992 Geo Tracker. It features a bolt-on install with no cutting, drilling, or welding required. This is a class I hitch which means the maximum number of bikes that can be carried is two, regardless of capacity. This has more to do with leverage than capacity. There are unfortunately only class I options for this vehicle.
The only way to safely carry more than two bikes would be on the roof with a roof bike rack.... view full answer...
We can help you with the wiring and other components required to ready your 1990 Geo Tracker for flat towing behind your Newmar RV. Safe and legal flat towing does require a few items and the three linked articles will give you detailed background to aid your selection. The basic components needed to flat tow include a tow bar, safety cables, a wiring/lighting kit of some type and base plates and a braking system for the towed vehicle. A high/low hitch adapter is also often helpful to keep... view full answer...
For Roadmaster base plates # 118-8 for your 2-door 1997 Geo Tracker you can use any Roadmaster tow bar.
The most popular tow bar is the Falcon 2, # RM-520. But if you were looking for something a little more cost effective you could use the Tracker tow bar to tow your Tracker, # RM-020. You will also need safety cables, # RM-643.
Next you will need lighting. I recommend going with a magnetic kit like # RM-2120 This kit will bypass the vehicle wiring.
And finally, most states now require... view full answer...
The Curt Trailer Hitch Receiver, # 11128, was designed for the 1993 Geo Tracker and offers bolt-on installation with no welding required. This hitch provides a 1-1/4" by 1-1/4" hitch receiver opening.
The recommended ball mount for the Curt Trailer Hitch Receiver, # 11128, is part # C45521. A pin and clip are included with the ball mount so you'll just need a hitch ball, part # 19256 for 1-7/8" or part # 19258 for 2".
If you need trailer wiring, take a look at the Upgraded Circuit Protected... view full answer...
For your 1997 4WD 4-Door Geo Tracker, the Roadmaster XL Base Plate # 1007-2 provides a custom fit. The base plate you referenced, # 118-8, works only for the 2-door models of the 1997 Geo Tracker.
For this item, there is no welding required and it is a vehicle-specific base plate that ensures a perfect fit for your Tracker. It is compatible with Quick Disconnects and all Roadmaster tow bars. I have included a photo showing a close-up view of how this product will fit on your vehicle.
I... view full answer...
Go To Results