Expert Answers about Ford Fusion
- Speaker Bracket Needed For Installing EcoHitch on a 2019 Ford Focus
- The bracket # 18136 was modified by our installer(as seen in the video below) to make a custom mounting bracket for the speaker on a 2020 Ford Fusion. This will require drilling of new holes in the bracket as well as an extra bend placed in the bracket to work on your 2019 Ford Fusion.
The EcoHitch Hidden Trailer Hitch Receiver # 306-X7239 does not come with the bracket as it is not required for every Fusion.
view full answer... - How Tall is the Vertical Arm of the Thule Hitching Post Pro Hitch Mount Bike Rack
- I went to our warehouse to measure Thule Hitching Post Pro # TH934XTR and the height of the vertical arm is 32-1/8 inches long. See the diagram I included.
I also measured from the center of the shank to the top of the vertical bar. It measured 33-3/4 inches. See the diagram I included.
I also included a helpful article for you to look at.
view full answer... - Parts Needed To Install a Brake Controller and 6-Pole Connector on 2015 Ford Fusion
- Before deciding to tow your camper with your Ford Fusion, I recommend checking your owner's manual for the towing capacity of your vehicle. It is important to not exceed the manufacturer's maximum towing capacity for your vehicle.
Since your micro camper has a 6-way trailer connector, it is likely that the trailer has electric brakes. To power your trailer's brakes, you will need a wiring harness, a brake controller, and a brake controller installation kit.
To start wiring your 2015...
view full answer... - Recommended Stacked Receiver To Flat Tow A 2019 Ford Fusion And Carry An E-Bike With
- Because of the way the Blue Ox Avail Non-Binding Tow Bar # BX7420 folds up for storage you are going to have to remove your bike rack from the Replacement Shank for Gen-Y Adjustable Ball Mount # 325-GH-303 prior to folding up the tow bar. To completely clear the bike rack you would need too long of an extension to be safe flat towing your vehicle.
While it's not as convenient I do recommend going with a stacked receiver and placing the bike rack in the highest receiver with your Avail...
view full answer... - All Trailer Lights Come On While Using Curt T-Connector On a 2016 Ford Fusion
- In regards to the Curt T-Connector Vehicle Wiring Harness part # C56351 which is a fit for your 2016 Ford Fusion, I would first check to make sure you have the wire leads ran to the proper sides of the vehicle. The lead with green wire goes to the passenger side and the lead with the yellow wire goes to the driver side. If you have the leads on the correct sides then make sure the pin inside the connectors are all straight and non are corroded.
I can't think of anything else that would...
view full answer... - Trailer Hitch Installation Process For A 2013 Ford Fusion 2.0 Turbo Model With Dual Exhaust
- While in the standard installation instructions it really makes no specific reference to differences with the 2.0 Turbo Model with dual exhaust. I did contact Curt on your behalf to see if their tech team had some insights for installing the # C12091. They said there was no difference in installation except you're dropping 2 exhausts instead of one. Some Sport models of the Fusion are not a fit but your 2.0 Turbo they confirmed is a Sport model that still fits so you should be fine to...
view full answer... - Towing Capacity of 2016 Ford Fusion and Trailer Hitch and Wiring Harness Fit
- According to the Ford towing guide, your 2016 Ford Fusion can tow up to 1,000 lbs unless it has the 2.0L I4 EcoBoost, which would give it a 2,000 lb capacity, though I recommend verifying this with your local Ford dealer. To tow you will need a trailer hitch, wiring harness and ball mount, and the best parts for that on your '16 Fusion are:
- Draw-Tite Sportframe Trailer Hitch Receiver # 24897
- T-One Vehicle Wiring Harness # 118574
- Draw-Tite Drawbar # 3594
- 1-7/8" Hitch Ball # 19256...
view full answer... - How Much Air Dam Trimming is Required to Install 2011 Ford Fusion Base Plate Kit # 4420-1
- When installing the Roadmaster XL Base Plate Kit, item # 4420-1, on your 2011 Ford Fusion, you will need to remove a portion of the lower air dam on each side of the vehicle. I have included a photo that details the area to be removed. We also have installation instructions online, see link, for this kit. On the Fusion, the cutting is minimal and the area cut will be filled in for the most part by the receivers for the tow bar brackets.
You should also refer to your vehicle owners manual...
view full answer... - Hitch and Rola Bike Rack Recommendation for a 2014 Ford Fusion Titanium Hybrid
- For a trailer hitch for your 2014 Ford Fusion for carrying a bike rack you would want the Draw Tite hitch part # 24897 which is a confirmed fit and does not require the use of a stabilizer strap like the Curt hitch you mentioned does. This has been confirmed as a fit for your Fusion Hybrid Titanium as well.
The Rola TX-102 you mentioned would fit this hitch well but has been discontinued.
The most popular bike rack we carry that has been confirmed to fit this vehicle is the Thule Camber...
view full answer... - Will a Draw-Tite Trailer Hitch Fit a 2010 Ford Fusion with Single Exhaust
- The Draw-Tite Class I Trailer Hitch Receiver, # 24865 is designed to fit all styles of the 2010 Ford Fusion including those with single exhaust. It is a pretty basic installation. You will need to lower the exhaust pipe by removing the rubber isolator at the muffler and one isolator near the rear suspension. I have included a link to a video showign a typical installation on a model with single exhaust.
view full answer... - Can the Lower Body Fascia be Reinstalled with Curt Trailer Hitch # C12091 on 2013 Ford Fusion
- It is not recommended to reinstall the lower body fascia with the Curt Class II Trailer Hitch, # C12091, on your 2013 Ford Fusion Titanium because of the final position of the hitch once it is installed. It may be possible to mount the fascia with the hitch installed, but you will have to do extensive trimming to make it fit with the hitch. The side mounting brackets, crosstube and receiver sit in the same location as the lower body fascia, so you would basically have to cut around the...
view full answer... - Does Curt Stabilization Strap Requirement Indicate Difference in Hitch Quality
- Curt's USA-made hitches like # C11390 that have the support strap # 18050 requirement for static loads like bike racks are just as well-made as those from Draw-Tite which do not share this requirement.
Curt's warranty policy requires the strap for many of their hitches, but in truth almost any hitch that will be handling the load of a bike rack or cargo carrier will benefit from using one or even two of the straps to steady the rack/carrier in the hitch as you go down the road. In no...
view full answer... - Recommendation For Replacement Driver Side Mirror For 2010 Ford Fusion
- The K-Source Replacement Side Mirror, Item # KS61605F, is a confirmed fit for your 2010 Ford Fusion but it is for the passenger, not driver, side. Since your Fusion does not have the heated mirrors currently, a replacement mirror will not be able to use the heat option.
For a replacement mirror for the driver side, I recommend the K-Source Replacement Side Mirror, Item # KS61600F. It fits the driver side, does not have the heat option, and is a confirmed fit for your 2010 Ford Fusion....
view full answer... - Is There a 2 Trailer Hitch Available for a 2009 Ford Fusion
- I do have an option for you, but they do not make a 2" trailer hitch receiver for your 2009 Ford Fusion to my knowledge. Instead, you will want to choose from the Curt Trailer Hitch Receiver part # C11329 which has a 1-1/4" receiver tube opening.
In order to get a 2" receiver tube opening on your Fusion you will need to use an adapter like part # HTAD but please keep in mind that this will reduce the hitch capacity by 50%. If you can tell me what you need a 2" trailer hitch for, I would...
view full answer... - Wiring 2015 Ford Fusion For Dolly Towing Behind RV
- What you propose is indeed doable. You'd need the Roadmaster Hy Power Diode Wiring Kit, part # RM-154. If you click on the provided links, you can see an install video showing the kit being installed on a different Ford vehicle. The procedure for your Fusion would be similar.
The product description page for the # RM-154 has install diagrams at the bottom of the page.
view full answer... - Bike Rack Recommendation for a Motorhome Flat Towing a 2011 Ford Fusion
- There are bike racks specifically rated for use behind a motorhome, and there are bike racks specifically designed to be used while towing (towing bike racks). However, none of the racks rated for use behind an RV are towing bike racks. But, what you can do is use a trunk mounted bike rack on the 2011 Ford Fusion.
For a 2 bike trunk mounted rack, I recommend the Yakima Fullback 2 # Y02634. This is a quality 2 bike rack with anti-sway cradles that will not brake the bank and it includes locks.
view full answer... - Will Rhino-Rack Roof Rack Fit a 2014 Ford Fusion Hybrid with Moonroof and Hold Kayaks and Bikes
- The Rhino-Rack roof rack # RR52SR is a fit for all models of the 2013 to 2016 Ford Fusion so I am happy to report that it will fit your Fusion hybrid. The moon roof, if it opens into a cavity in the roof and doesn't raise up above the roof line, will not be an issue. If it does rise up above the roof line then it is possible that a crossbar could get in the way.
As far as the capacity of the roof rack I did some checking and the roof does not have a listed capacity in the owner's manual....
view full answer... - Trailer Hitch and Wiring for a 2006 Ford Fusion
- That was a nice gift but Hidden hitch trailer hitch 60282 will not fit a 2006 Ford Fusion. It used to fit 2010 to 2012 Fusions, 2010 and 2011 Mercury Milans, and 2010 to 2012 Lincoln MKZs. But that hitch is now discontinued.
The comparable trailer hitch for the 2006 Ford Fusion is the Curt # C11329. If you plan on doing some towing the correct ball mount is # 3592. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # 118422. I have linked a video...
view full answer... - Will the WeatherTech Custom Auto Trunk Mat Fit my 2014 Hybrid Fusions Hybrid Trunk
- Yes the black Husky Liners WeatherTech Custom-Fit Cargo Liners for your trunk # WT40959 that you referenced is confirmed as a custom fit for your 2014 Ford Fusion Hybrid model.
For your reference, I have also included a link to the other trunk and floor mats that are confirmed to fit for your vehicle.
view full answer... - Roof Rack Recommendation for 2013 Ford Fusion Titanium Energi Model
- The Rhino Rack roof rack that consists of part numbers # RRVA126B-2, # RRRLKVA, and # DK358 has been confirmed to fit all models of the 2013 Ford Fusion so it will work well with your Titanium Energi model.
The clamps of the included fit kit are specifically designed to fit the profile of the door jambs of your vehicle and would work well.
This rack has a weight capacity of 165 lbs; you will need to consult the owners manual of your vehicle to determine the roof capacity of your vehicle...
view full answer...
Go To Results