So I did some research on whether or not your 2016 Ford Edge Titanium AWD can be flat towed and it looks like the deciding factor is the engine size. If you have the 4 cylinder 2.0 liter engine you can't flat tow it and it must be towed on a trailer. If you have the V6 engine though you are totally safe to flat tow the vehicle as long as you follow the procedures listed in the owners manual.
The Blue Ox base plate kit you'd need is the part # BX2667 if you have adaptive cruise control... view full answer...
To flat tow your 2013 Ford Edge with your existing Demco Tow Bar you will need a set of vehicle specific base plates and a tow bar adapter.
The correct base plates for your Edge if it is equipped with adaptive cruise control at the Roadmaster EZ Base plate kit # 524426-1. If your Edge does not have the adaptive cruise control then you would use the Roadmaster XL Base Plates # 4408-1.
Once you have the base plates installed on your vehicle then you can use the Roadmaster Tow Bar Adapter... view full answer...
I looked through an online copy of the owners manual for the 2013 Ford Edge Limited and the #59 fuse looks to me like the only one you would need to pull. If the vehicle still starts then you would need to go with the normally open instructions for brake light relay # RM-88400. I have included a picture showing how it is set up normally open. view full answer...
Almost certainly, yes.
You did not specify which Thule rooftop box you have, but a fit should not be an issue due to the small 3-1/8" wide x 1" tall JetStream aero bars.
The roof rack you are talking about for your 2017 Ford Edge is made up of BaseLine Towers # Y28TR, Fit Kits # Y06102 and # Y06139 as well as the JetStream Crossbars # Y00425 and will have a spread of 32 inches when installed on your Edge.
I do recommend using the Yakima SKS Lock Cores # Y07204 to secure the rack to... view full answer...
Trailer hitches can bend and flex a little in the shipping process and that is likely what has occurred with the hitch you received, # 75214. This hitch is indeed a fit for the 2015 to 2018 Ford Edge SE, SEL, and Titanium.
The hitch can be flexed back into position relatively easily. I have included a link to our help article that covers exactly this issue and how to correct it. view full answer...
For your 2015 Ford Edge Sport the Draw Tite Hitch part # 75234 would be your best option. It has a hidden crosstube which means visibility of the hitch would be reduced and because it has also been tested to still allow the hands free lift gate to function. Draw Tite states:
"Hands-free Liftgate sensor areas will be limited to areas away from the center where hitch receiver opening is located." So basically you just have to kick to either side of the hitch tube.
For trailer wiring you... view full answer...
The best option I have to activate the reverse lockout feature on a boat trailer would be to first integrate the circuit into the trailer connector with the Hopkins Endurance 5-Way Flat Trailer Connector part # HM47910. Once this is done you can use the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter part # 20036.
The blue wire will need to be spliced into the the reverse light circuit on the vehicle but in regards to the exact process or route I wouldn't have much on this as it varies... view full answer...
As brake controllers will only use 4 wires, two of the 6 ports will not have any function. With that being said, you most likely have a fuse out, causing the lack of power to your controller. A quick way to test this will be to use something like the Circuit Tester Kit # PTW2993 and see if there is power going to the bottom left port on the vehicle plug (picture included).
If you are not getting power, you most likely have a fuse out. I was able to find the location of 2 fuses that should... view full answer...
We have a few different roof rack options that will fit your 2018 Ford Edge Titanium with the Vista roof and no side rails. For this, I recommend taking a look at the Rhino-Rack Vortex Aero Crossbar System which is composed or part # RRVA137B-2, part # RRRLKVA, and part # DK432.
The Aero Crossbar system will produce less wind noise and drag so it is the more popular than square bar systems. I like Rhino-Rack because they have the same level of quality as the bigger brands like Yakima... view full answer...
Yes. The Blue Ox # BX2667 baseplates for a 2016 Ford Edge are compatible with the Blue Ox Aventa tow bar without using an adapter. This base plate kit has removable arms to allow your Edge to have a clean looking front end when you're not flat towing. view full answer...
Actually, all of the hitches available for the 2019 Ford Edge, regardless of trim level will have the sensors for the Hands-Free liftgate feature blocked at the middle of the bumper. This is because the receiver tube extends below the bumper and would sit between where you'd sweep your foot and the liftgate sensor. The system uses 3 or 4 sensors (depends on the vehicle) and the sensors will still pick up movement but you'll need to sweep your foot to the left or right of the center of the... view full answer...
Yes, the T-One Vehicle Wiring Harness # 118677 is a confirmed fit for your 2015 Ford Edge Titanium.
If you don't already have a trailer hitch then I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver # 75234 because it is the only option that has a hidden crosstube which gives you a very clean look after the installation.
To complete a towing setup you also need a ball mount kit. I recommend checking out Ball Mount Kit # 989900 because it includes two ball mounts, one with a 3/4”... view full answer...
In order to pick out the correct bearing buddy you will need know the hub bore diameter of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into place. Use a screwdriver to pry off the cap.
Clean the grease off and measure the opening. I have included a video demonstrating the Bearing Buddy.
The Bearing Buddies # BB1980A-SS are for hubs with a 1.98 inch hub bore. view full answer...
Correct, the Thule Snowpack Carrier # TH7326 will work with your factory crossbars on your 2017 Ford Edge due to the SpeedLink Mounting System. Its a simple tool free way to get the carrier on your roof and secured in little time.
I've included a video for you to watch to get a closer look! view full answer...
You can use the Thule Gateway Pro 2 Bike Rack # TH88VR you mentioned on your 2014 Ford Edge while towing your camper. However you will most likely need to use an extended ball mount to make sure you have enough clearance so you don't run the risk of hitting the bikes, rack, trailer jack or propane tanks.
If you provide me with the ball mount size, how much rise or drop you have I can make a recommendation for an extended ball mount.
To carry women's bikes, kid's bikes or alternative... view full answer...
The closest screen door slider available is the Lippert Motor Home Entry Screen Door Bubble Slider Panel - Frosted Item # LC234101. It measures 12" x 12" x 1-3/16". view full answer...
I checked the Tow Ready website and called and spoke to my contact to verify and both indicated that the T-One Connector w/Upgraded Circuit Protected ModuLite, # 118515, will fit the 2011 Ford Edge. It was specifically designed for and tested on 2011 models. I have included a link to the installation details for reference. view full answer...
For your 2018 Ford Edge without the factory side rails and a moonroof I recommend taking a look at the Yakima JetStream roof rack system. This consists of # Y00425 for the two 50 inch long JetStream Crossbars, # Y28TR for the BaseLine Towers, # Y06102 for the Front Fit Kit, and # Y06139 for the Rear Fit Kit. This is confirmed to fit the naked roof of your vehicle and will work just fine with the moonroof. It has a 165 pound weight capacity.
I have attached the written installation instructions... view full answer...
It may be possible to fit 3 bikes on the Curt 24x60 Cargo Carrier # C18152 but I have no way to confirm it since it is not what the cargo basket was designed for. In my mind the best chance of fitting would be to alternate the direction the bikes are facing and use ratchet straps # ETBMB-05852 to secure the bikes. The Curt # C18153 internal dimensions are 60-1/8" long x 23-3/4" wide x 5-1/2" deep, you can use the dimensions compared to the dimensions of your bikes to see if you will be... view full answer...
None of the trailer connector mounting options we offer are vehicle specific, so finding a way to attach the connector to the vehicle could involve some trial and error. If you have access to the hitch crosstube, you can use a mounting box like part # 18159. Another option would be a no-drill bracket like # C57202 attached to the crosstube, and then you would use a bracket like part # 18138 to attach the 7-way connector to the no-drill bracket.
I have also seen instances where folks have... view full answer...
Go To Results