The Hollywood Racks 2 Bike Carrier, part # HRF2 is a confirmed fit for all model years of the Honda HR-V with a spoiler. This rack is designed to fit around the spoiler and avoid resting weight directly on the spoiler to prevent damage to it.
Additionally, it includes integrated anti-sway cradles that will reduce the motion of the bikes while suspended, minimizing the risk of damage.
Using a Swagman Frame Adapter, part # 64005, is also an easy way to reduce the risk of damage to the... view full answer...
The blue straps for the Thule Passage 3 Bike Rack, part # TH911XT will connect to slightly different places than they normally do on a 2007 Mercedes-Benz C-Class.
Your top straps will go at the front edge of the top of the trunk, while your bottom straps will go along the bottom of the trunk, and you'll make sure that your carrier's bottom arm is on the upper tier of the bumper. Thule also recommends removing the rack if you do not plan on using it.
I've included a video of a 2013 Lincoln... view full answer...
I do have options for you but the Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D would not accept AC current from shore power and then use that to charge your two AGM batteries while disconnected from the tow vehicle. The Redarc In-Vehicle BCDC Battery Charger would still be needed while driving but when parked you would need to install a power converter to charge the batteries using shore power.
The correct power converter will vary depending on the A/h of your batteries... view full answer...
You'll need to do just a bit of measuring to determine if you can use the Yakima LockNLoad Platform Rack for Crossbars - 55" Long x 49" Wide # Y05044-39.
I have added diagrams from Yakima below that show you exactly what to measure and the measurements you need to have in order to use the # Y05044-39, which is platform size K. From inside to inside of your roof rack towers the measurement needs to be at least 34" and 45-1/4", and from center to center of your towers (front to back) it... view full answer...
According to the installation instructions for CURT Trailer Hitch, # 11824, which I have linked for you to view, you will need to drill a total of 4 holes to install the trailer hitch. Two holes will go through a cross member under the car and the other two in the bumper beam. (There is actually a 5th hole that will be drilled but it is for routing bolts for installation.)
The gross trailer weight capacity of this trailer hitch is 2,500 pounds, which is more than enough to handle the 1,800... view full answer...
If your 2011 Mercedes Benz C300 Sedan has a thin lip spoiler on the trunk lid you should have no problem installing a trunk mounted bike rack on your 2011 Mercedes Benz C300. For carrying two bikes I recommend you get a Thule OutWay 2 Bike Trunk Mounted Carrier # TH45JV. This rack is confirmed to fit your vehicle and is one of the best racks available due to how well it carries bikes and how easy it is to install and un-install. Check out the review video and installation instructions for... view full answer...
The least expensive trunk mounted bike rack that will fit your 2010 Mercedes C320 is the Hollywood Racks Express, # HRE3. This rack is a very basic rack. It does not include anti-sway cradles and is not the best option for anything other than short trips.
The best trunk mount rack we offer is the Thule OutWay, part # TH45JV. Instead of the 4-6 difficult to use straps and buckles that need to be adjusted each and every time the rack is installed or removed, the Raceway features 2 rubber... view full answer...
I checked on the 2011 Mercedes C350 and there are no hitches available for the coupe models. The # C11030 that you referenced will work on the sedans but not the coupes.
Since I do not know what year BMW 3 series you have I can not say for certain if a hitch is available. Email me back and I will let you know if there is one available.
I checked and the Thule OutWay Bike Carrier # TH45JV will work on your C350 and every generation of BMW 3 Series coupes so I believe it would be a good... view full answer...
Yes, since each of the Greystone Countertop Side-by-Side RV Griddle and Grill # WAY94FR burners have a 12K Btu capacity you're potentially looking at 36K Btu when using all 3 of them. view full answer...
We have a many solutions to work with your 2020 Mercedes-Benz C300 Sedan. Here are just a few of them.
My recommendation is the Thule SnowPack Extender Ski and Snowboard Carrier - Slide Out - 6 Pairs of Skis or 4 Boards - Black # TH732508. It will fit your factory cross bars with a quick clamp on style. It can carry 6 pairs of skis or four snowboards.
Next choice would be the Yakima FreshTrack 6 Ski and Snowboard Carrier - Locking - 6 Pairs of Skis or 4 Boards # Y03093. It is a similar... view full answer...
The Adco RV Windshield Cover for Class C Motorhome - Vinyl - White # 290-2423 will fit your 2021 Tiffin Wayfarer on a 2020 Mercedes Sprinter Chassis. view full answer...
The two bearings you mentioned have different inner diameters. The # L44643 has an inner diameter that is exactly 1 inch and the # L44649 is 1.06 inch. This may not seem like a lot but it's a big enough difference to prevent the hub you have now from fitting your spindle (you may already know this). The seals are slightly different diameters too.
Since you wouldn't be able to swap out the bearings of your current hub to the correct size you need (the hub won't match), the only solution... view full answer...
The Ultra Fab kit part # UF39-941705 would be a great option. This attaches to the bottom of the frame of your camper and allows you to independently control to jack legs on either side of the trailer to level and stabilize it.
I attached a review video for this jack for you to check out as well. view full answer...
There are trailer hitch receivers that will fit each of your Mercedes, though there is not one that can fit either/or or is in any way transferable. The Curt Trailer Hitch Receiver, # C11030, is a confirmed fit for the 2010 Mercedes C-Class.
This hitch has a 1-1/4-inch receiver opening and has a Class I rating, which means the hitch's maximum tongue weight is 200 lbs and max gross trailer weight is 2,500 lbs.
For a cargo carrier, the 20x48 Curt Cargo Carrier, # C18110, will fit 1-1/4-inch... view full answer...
To install the Curt Class I receiver, the bumper on your M/B C240 will need to be temporarily removed in order to drill holes.
To see the installation instructions, click on the provided link. view full answer...
While we do not have what you're looking for, but if storage is the issue, then you can just trim the excess of the Lippert Waste Master RV Sewer Hose w/ Leakproof Camlock and 90-Degree Nozzle # LC359724 and glue the pieces back together with the Valterra ABS Solvent Cement # A05-0303.
This will allow you to trim the hose down to a manageable length for your RV and still allow you to use it.
Attached are a couple of videos for you to check out as well.
If you're after something different,... view full answer...
The Curt Class I Hitch # C11485 works on both the Sport and the "excluding Sport" version of the 2021 Mercedes-Benz C-Class Convertible. It's the same hitch # C11485 on two different listings. That's one of the fun side effects of our new and improved website fitguide.
All hitches that fit your vehicle are going to be Class I 1-1/4 hitches. If you are going to use it for accessories like the Kuat Sherpa Bike Rack # SH22G, then note that you can only have a maximum of two bikes on your... view full answer...
When installing a powered converter like the # C59236 on a vehicle, people will usually run the power wire along the underside of the vehicle, by following an existing wiring harness as it runs under the vehicle up into the engine compartment. As the wire goes from the rear to the front of the vehicle, be sure to avoid anything that's moving like suspension or steering components or hot like exhaust components. I don't have specifics to offer you, but we have a helpful FAQ article that... view full answer...
There actually isn't any fascia trimming required to install Curt trailer hitch # C11030 on the 2009 Mercedes C-Class. I have linked a video showing an example installation as well as the instructions showing the steps to install the hitch.
For future reference though using a rotary tool is the easiest way to trim fascia and it also provides the cleanest cut. Other methods include using snips of some kind (depends on the material being cut) as well as a sharp box cutter.
If you want to... view full answer...
Moving up a higher load range will not only increase your load capacity, but will also increase the sidewall ply strength, so you will be less likely to have a blow out. I recommend the Kenda 5.30-12 Bias Trailer Tire with 12" White Wheel - 5 on 4-1/2 - Load Range D # AM30859 for your application or the galvanized wheel # AM30861. These combinations use the same tire which is rated for 1,250 lb capacity at 105 psi. You want to always run trailer tires at their max psi when inflated while... view full answer...
Go To Results