Expert Answers about Workhorse
- Replacement Hydraulic Brake Actuator For A DA-66 Actuator
- Yes, the Demco Hydraulic Brake Actuator # DM72VR will be a good replacement for your older actuator DA-66. This actuator has a bolt-on installation and requires 2-1/2 inch x 4-1/2 inch grade-5 bolts which are not included. The actuator works with drum brakes and has a gross towing weight of 7,000 pounds with a maximum tongue weight of 700 pounds.
I linked an installation video below on installing the Demco Hydraulic Brake Actuator. If you have any further questions please feel free to...
view full answer... - Recommended Suspension Enhancement for a 2006 Workhorse W42
- Adam, we don't have any air springs unfortunately for your 2006 Workhorse W42, but we do have the Timbren Rear Suspension Enhancement System # TGMRP30.
These are hollow rubber springs that sit above the rear axle, has up to 6,000 lbs of capacity, and requires no drilling for installation.
view full answer... - Correct Pigtail for the 7- and 4-Pole Trailer Connector Socket
- It sounds like you are looking for the Pigtail Wiring Harness part # PK11998 which will plug directly into the back of the 7- and 4-Pole Trailer Connector Socket part # HM40975. The Deka Heat Shrink Butt Connector part # DW05744-5 and part # DW05745-5 can then be used to make the above connections.
view full answer... - How to Find Centering of Draw-Tite Max-E-Loader Trailer Hitch Receiver for Motorhome
- The Draw-Tite Max-E-Loader Trailer Hitch Receiver # 41547 is symmetrical so while I don't have the center location of the receiver right off-hand, what I can say is that you will be able to measure the distance between the mounting points (or even the frame of your vehicle) and the receiver will be right in the middle of that measurement (see attached).
view full answer... - How to Remove Lug Nut Caps on a Motorhome
- The Wheel Masters Lug Nut Cover Pliers # WM8211 is designed to remove the lug nut covers on a RV. We have used sockets to remove the covers in the past but using this tool lessens the chance of damaging the finish.
view full answer... - Finding The Correct Replacement Entry Door Lock For A 2001 R-Vision Trail-Lite M-241
- Manufacturers do not list the door handle locks used so you would need to remove the door handle lock from the entry door of your 2001 R-Vision Trail-Lite M-241 Motorhome and measure the cutout hole to find the size needed. For example the Bauer Products Motorhome Door Lock - Black # BA64FR requires cutout hole of 5-1/4" wide x 4-1/2" tall and a door thickness of 1-1/4" to 1-1/2" thick to install.
view full answer... - Can The 2022 Honda CRV 2WD Be Dolly Towed
- According to the owner's manual for the 2022 Honda CRV a 2WD model can be dolly towed with the front two wheels up on the dolly. The Roadmaster Tow Dolly with Electric Brakes - 4,250lbs # RM-2050-1 has sliding ramps that can fit a tread width of 34" to 77", so it will easily accommodate your 63" track width.
Because this dolly has electric brakes it does require that your motorhome has an electric brake controller. If you don't have one let me know and I can help find the correct parts...
view full answer... - Installation Instructions of Front Bags on 2003 Itasca SunCruiser on Workhorse W22 Chassis
- When installing the AirLift # AL88101 you do not need to remove the factory jounce bumpers and they will not be installed in the same place. You will want the air bags to install forward of the axle and your stock jounces should be behind the axle. Additionally, because of their size, the AirLift bags will engage before the stock jounces so they can be removed if you desire.
view full answer... - What Replacement Fan Do I Need for a Fantastic Vent Lift Motor 6051- 05, 8RPM?
- The replacement part that you need for your 2002 Newmar Mountain Aire is the Replacement 17-rpm Lift Motor for Fan-Tastic Vent B Series Roof Vents # FVK6010-81. The Replacement Fan-Tastic Roof Vent has a higher RPM than your 8RPM fan. However, I confirmed with my contact at Fantastic Vent that since your fan is of a lower rpm and manufactured before 2014, this motor will still work, but you will need to cross the wires. For example, instead of red to red and black to black, you will need...
view full answer... - Does Roadmaster Reflex Steering Stabilizer # RM-RBK- RSSA Fit W22, W22, and W24 Chassis
- The Roadmaster Steering Stabilizer part # RM-RBK13-RSSA does fit the W20, W22, and W24 Workhorse chassis like you asked about.
view full answer... - Wiring for Prodigy P3 Brake Controller on 2004 Workhorse W22 Chassis
- There isn't a brake controller port that I am aware of on your motorhome built on a 2004 Workhorse W22 chassis, but you can check up under the dash for a bundle of wires; they would have a white tag on them. It would generally be to the far left side under the dash if they are there.
If those wires are there you would be able to simply splice in the Tekonsha Prodigy P3 Trailer Brake Controller # 90195.
If that bundle of wires is not there you will need the Wiring Kit for 2, 4, 6, and...
view full answer... - Replacement Parts for Series 25 Kwikee Steps
- The only parts list for your triple step is attached. It unfortunately does not give the breakdown to the extent you are seeking with Teflon plate and wave washer as those parts are not replacement options from the manufacturer. I've attached the best parts list from the manufacturer I can get as an attempt to help. If your parts are worn then I recommend getting the replacement kit # LC379804 because not all the parts you are seeking are replacement options.
view full answer... - Size of Bolt that Comes with Timbren Kit part # TWRW22
- The bolt size that comes with the Timbren kit part # TWRW22 is M10x60mm x 1.5. Basically just enough of the bolt comes through the assembly and frame to secure it with the nut on the truck frame.
view full answer... - Steering Stabilizer for a 2008 Fleetwood Bounder on a 2007 Workhorse W22 Chassis
- The Roadmaster Reflex steering stabilizer that fits the 2007 Workhorse W22 chassis is actually # RM-RBK13-RSSA. The one that you referenced, # RM-RBK14-RSSA, is for Freightliner chassis.
The steering stabilizers will come with the mounting brackets and hardware. Current pricing is available on each product page.
view full answer... - SumoSpring Recommendation for 2005 Workhorse W-22 Simba 36 DBD Towing Trailer
- If you plan to do some towing with your 2005 Simba 36 DBD Workhorse W22 then a rear set of SumoSprings like the part # SSR-280-54-1 that you referenced would be a great choice. This will give the rear suspension more support to help prevent sagging and give you the best overall towing experience.
In your last sentence you said were trying to push as much weight to the rear of the trailer as possible. You should note that's not an ideal way to load the trailer. This will most likely cause...
view full answer... - Air Bag Kit Recommendation for Front Axle of 2000 Workhorse P30 Chassis
- The Air Lift Kit part # AL81560 that you referenced is the correct air bag kit for the front springs of your 2000 Workhorse P30 chassis that your Itasca Sunrise is built on. You would need to remove what is there now and install these in place of them.
I wish we had the bushing you need, but at this time we do not have stock sway bar bushings for RVs like yours.
view full answer... - Is Drilling Required for the Air Lift Air Springs AL57202 for a Workhorse P30 Chassis
- The Air Lift LoadLifter 5000 Air Helper Springs part # AL57202 which are a fit for the Workhorse P30 Chassis will require you to remove the existing jounce springs. The air springs will also require drilling into the frame but only a few holes so nothing too major. The Air Lift LoadLifter 5000 Air Helper Springs are the best option for the Workhorse P30 Chassis so they are worth the extra troubles for installation.
view full answer... - Troubleshooting Kwikee Stelps Not Operating Correctly When Updated With Replacement # LC379804
- It sounds like the circuits for the Kwikee step on your 2004 Winnebago Adventurer 35U are normally closed. The Replacement Motor with Table for Kwikee 25 Series Electric RV Steps # LC379804 does require normally open circuits. These are typically always black like those from the list below. Your circuits most likely will be white but do know that different manufacturers do not always accept the color standards so you can check your wiring to determine if they are an open or closed circuit....
view full answer... - Is Weight Capacity for Timbren Suspension Kit # TWRW22 for Both Springs or Per Spring
- The capacity of the Timbren Rear Suspension Enhancement System # TWRW22 that you referenced is 8,600 lbs for both sides together. You should note that these kits give you additional suspension support but they do not add to the capacity of the vehicle. They only allow you to carry your current capacity in a safer way.
view full answer... - Recommended Tire Pressure Valve Extenders For Motorhome
- The Wheel Masters Tire Pressure Valve Extenders - 90-Degree Bend - Front Wheels # WM802990 technically are designed for the front wheels, but there are several customers that left reviews stating that it worked on their rear wheels. It really just depends on the layout of your current valve stems and if it requires a bend at all.
I recommend looking into Wheel Masters Tire Pressure Valve Extenders - 135-Degree Bend - Steel Rear Wheels # WM8029135 or Wheel Masters Tire Pressure Valve Extenders...
view full answer...
Go To Results