In a sense you're overthinking it, yes.
The Blaylock EZ Jack and Wheel Chock for Tandem-Axle Trailers # EZ-JACK can be used both to help level out your trailer on uneven ground but it's also great for temporarily raising a side of the trailer to change out a tire like what you mentioned doing. You just want to avoid leaving your trailer in that position for an extended period of time at full capacity.
If you do need to leave your trailer jacked up like that for a while then you need to... view full answer...
For determining the proper size Solera slide-out awning, you need to measure the total width of your slide room from the outside including the flange and then add a minimum of 5" (2-1/2" each for the left/right side overhang). You can have greater than 2-1/2" overhang if you want, but it is suggested that you do not go any less. If you have done so with resulting measurement of 96" you need an awning no less than 101". You can go beyond the overhang of 2.5" each side if you choose, no worries.... view full answer...
To easily fit the center portion of the Epicord Battery Disconnect Switch # 277-000096 through your wall you'd want to drill a 2-3/4 inch hole so that would be the size hole saw to use. view full answer...
While there is not a plug-n-play adapter to change from on brand to the other, you can still use the wires from the pre-wired Voyager system on the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision, # FOS05TASF by cutting the adapters from one and splicing to the other. view full answer...
The Progressive Dynamics Pure Sine Wave Inverter # PD34FR is designed to work with both a 30 AMP RV system or 50 Amp RV system. So regardless of which set up your 2017 Winnebago Minnie Trailer has this unit will work with it. This inverter is also compatible with both lithium and lead acid batteries so there are no worries about having the upgraded battery bank. The manual also states that the inverter should only be installed by and electrician or certified RV technician. view full answer...
Sounds like you don't have the correct rise or drop with your weight distribution hitch which is why you aren't level, and you don't need a brand new hitch, you can simply get a new shank. You didn't mention the exact one model you have, but so long as your current shank has 1-1/4" adjustment between the holes, you can use any brand.
You mentioned # FA94-00-1061 looking like yours, and that's a round bar system, so here are the options for the maximum rise or drop for round bar weight... view full answer...
You're correct that you need to measure from the outside edge to outside edge of the flanges.
If your measurement from flange to flange is 82.25" then you're going to want the Solera RV Slide-Out Awning - 7'1" Wide - 48" Projection - Black Item # LCV000165062.
It fits slide outs with a measurement from 80"- 85".
When measuring you won't need to add an extra 2.5" to each side to the measurement to pick the awning. The bracket arms that hold the roller to the slide out are going to... view full answer...
The Adco RV Cover for Winnebago Travel Trailer # 290-64844 is currently our most rugged cover for your Minnie and is the only cover we have for your 2019 Winnebago Minnie 2455BHS that has the Winnebago logo on it. This cover has a top panel that is constructed of a 5-layer polypropylene fabric that beads water on contact to prevent pooling, guards against harmful UV rays that can cause cracking and fading and eliminates black streaks and corrosion caused by air pollutants and rain. The... view full answer...
The easiest and most cost effective way to increase ride quality on a travel trailer like the Winnebago Minnie is to upgrade to cushioned equalizers. These will provide significant increases in smoothing out the ride. I recommend the Dexter E-Z Flex Suspension Kit as it's more of a complete kit since it comes with cushioned equalizers, wet bolts, and heavy duty shackles. The correct kit will be based on your axle spread, part # K71-652-00 for 33" or part # K71-653-00 for 35". view full answer...
You will need to use the Roadmaster Comfort Ride Leaf Spring Suspension Kit # RM-2460-2560 for your 2022 Winnebago Minnie 2529RG travel trailer. These leaf springs are rated for 5,000lb axles while the ones in the Kit # RM-2460-2580 you found are rated for 8,000lb axles. If you used the heavier springs your trailer would bounce a lot more and the suspension would not properly absorb the bumps. The kit # RM-2460-2560 also includes the shocks for mounting to your 3" diameter 4,400lb axles. view full answer...
Mike, it sounds like you're looking for the Triplex Wire with Grey Outer Jacket # SWC5362-1 which is jacked 14 AWG 3 wire.
Also, this is sold per foot, so if you needed 10 feet you'd need to order 10. If you're looking for something else, let me know below and I'll see what we have. view full answer...
Most leaf replacement trailer leaf springs are going to come with new bushings so I wouldn't anticipate you having to remove your old ones to install them in new springs. That said the bushings are removable if needed.
Since we know your 2018 Winnebago Minnie 2401RG has 3,500 lb axles for a replacement we have the part # e54SR which is 25-1/8 inches long. You'd need to measure your current springs to verify that this would work as we don't have a way to look up your current spring length... view full answer...
You do have the correct electric brakes for your 2017 Winnebago Minnie 2500RL with the TruRyde Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand - 3,500 lbs # TRU36FR.
The magnet would be an issue if you see their windings beginning to show through the friction surface of the magnet, but in general if the brakes are still functioning then the magnet is fine. The # TRU36FR come with magnets so you wouldn't have to replace those separately; the only other thing you... view full answer...
The Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 does require an I-Beam frame to be compatible so you would instead need to use a stabilizer like the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707, which can be used on c-channel frames. view full answer...
I reached out to my contact at Reese and the Replacement 1/2" Hardened Washer for Reese Weight Distribution Systems # 3306 you were looking at are the correct washers to adjust the hitch ball angle on your Reese Pro Round Bar Weight Distribution w Sway Control # RE44FR.
I included a video of the # RE44FR for you to take a look at. view full answer...
For a shock kit for your 2021 Winnebago 2401 Minnie with 3,500 lb axles you'd want the part # LC281255. Since hangers don't typically have grease fittings I believe what you are looking for would be cushioned equalizers like the Road Armor part # LC696740 which are correct size and rating for your trailer. view full answer...
We have a jack that matches exactly what you are looking for.
I recommend the Lippert Smart Jack Electric Trailer Jack w/ Footplate # LC643589 which has a 3500lb weight capacity and allows you to set the height you want the jack to raise and lower to so that you can raise or lower the jack with the touch of a button and not have to hold a switch.
The # LC643589 will replace the standard A-frame trailer jack in your trailer.
For a bumper mounted cargo carrier I recommend taking a look... view full answer...
Based on the dimensions you offered of your Winnebago's current equalizer, longer shackle straps will be needed in order to use the Equa-Flex Cushioned Equalizers # LC279687.
Since you mentioned also wanting wet bolts, we actually have a kit that has everything you need, the Lippert Components Tandem Axle Equa-Flex AP Kit # LC64FR.
This kit has the 3-1/8" long shackle straps you need, as well as wet bolts and nuts. The combination of the cushioned equalizers and wet bolts will give you... view full answer...
I recommend the Solera RV Slide-Out Awning - 7'1" Wide - 48" Projection - Black Item # LCV000165062 as it fits RVs with slide-outs 80" - 85" wide and up to 48" long. The recommended clearance for each side is 7" to allow the slide topper to properly close without damaging any nearby trim or other awnings. If you do have something that falls within the clearance of your slide topper reply back with the measurement and we'll get you setup with another awning that will work. view full answer...
The TireMinder TPMS for Dual Axle Trailers part # TPMS-TRAILER as you stated is only for trailers 25' or shorter. The Winnebago Minnie 2500FL measures 28' 3" long so I cannot recommend this. There isn't another solar powered version like this for longer trailers either so you will have to consider other options like the TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster part # TM89FR. The main difference is the monitor which will take up some space on your windshield and plugs into... view full answer...
Go To Results