The Inno Shaper 100 Roof Cargo Basket - Channel Mount # INXA569 is what you'll need to use if you want to install the cargo basket via the T-Slots on your crossbars. The Inno Shaper 100 Roof Cargo Basket - Square Bars # IN569 you're interested in has a different mounting hole configuration so the hardware used in the channel mount setup is, unfortunately, different. I confirmed this with my contact at Inno. view full answer...
The Curt Trailer Hitch Receiver part # C22UR is a fit for a 2021 Toyota Sienna and a great option. The design however will likely limit functionality of the hands free liftgate feature. It could still be operation by placing your foot on either side of the receiver tube opening but this is not something we have tested.
Unfortunately, all of the available trailer hitch options for this vehicle will likely impede use of this feature. view full answer...
In order for the Carr Custom-Fit Side Steps # CARR124031-1 to work on your 2021 Toyota Sienna, there will be some custom fabrication involved. This will include drilling directly into the frame of your vehicle. However, it is important to note that I confirmed with Carr that the Custom-Fit Side Steps are not designed to fit your vehicle. For that reason, there is no way to know for sure if they will fit. Also, The 500-pound weight capacity of the steps were not tested with your particular... view full answer...
So there is one main difference between the Class III trailer hitches that fit your 2020 Toyota Sienna, and that's the visibility of the crosstube, with there being options for a concealed crosstube and a visible crosstube:
Concealed Crosstube:
- Draw-Tite Trailer Hitch Receiver # 76112
- Curt Trailer Hitch Receiver # C13343
- etrailer.com Trailer Hitch Receiver # e98853
Visible Crosstube:
- Draw-Tite Trailer Hitch Receiver # 75237
- Curt Trailer Hitch Receiver # C13105
- etrailer.com... view full answer...
The Universal MightyMounts for Yakima Roof Mounted Accessories part # Y03590 is what you need to mount the Yakima HullyRollers on a Toyota Sienna with a factory aero roof rack. I know they may be more than you are looking to spend but they are the only option as far as an adapter goes. view full answer...
I took a look at the owner's manual for the 2012 Toyota Sienna and was not able to find a fuse location dedicated to trailer brakes. There was a fuse location for trailer lights but not brakes. It makes sense that the fuse location does not exist because the 2012 Toyota Sienna only came pre-wired for a 4-flat trailer connector from the manufacturer not a 7-way connector like what is needed to power trailer brakes with a brake controller.
It sounds like you may have a 7-way connector hardwired... view full answer...
To find the correct ball mount for your 2008 Toyota Sienna and 2003 Coleman Santa Fe tent trailer, there are a couple of measurements you will need to take.
First, Measure the hitch height from the ground to the top of the receiver opening on the trailer hitch. Make sure your van is parked on level ground.
Next, measure the trailer coupler height from the ground to the bottom of the trailers coupler. Again, the measurement is most accurate when on level ground. The trailer will also need... view full answer...
Yes, the Inno Wedge 660 Rooftop Cargo Box # INBRM660WH does fit the factory crossbars of your 2020 Toyota Sienna. On a white car I think this would look REALLY good. The black base of the box would provide enough contrast if there was any slightly difference in shade. I looked up pictures of your Sienna in super white though and it looks like a very close match if not a total match. Since your Sienna has some black trim it will match well to this box since it's also mostly white with some... view full answer...
Yes, the Thule Force XT XL Rooftop Cargo Box # TH6358B will fit perfectly with the Thule AeroBlade Edge roof rack on the raised rails of your 2019 Toyota Sienna.
Attached is a review video for you to check out! view full answer...
Yes, the Air Lift 1000 kit part # AL60732 that you referenced is a confirmed fit for your 2020 Toyota Sienna AWD so it would work great for you. view full answer...
Since you don't have the side rails there's only one option to add a roof rack to your 2017 Sienna. You will want the SeaSucker Monkey Bars Roof Rack item # 298-SX6000B. This roof rack attaches to your roof with suction cups and does not require drilling. It will give you a set of 48" round bars with a 150 lbs capacity.
I have linked an installation video below that will show you the functions of this roof rack. view full answer...
The 2,400 lb. load capacity of the Timbren Rear Suspension Enhancement System part # TTORSEN04 for your 2011 Toyota Sienna is per axle. You will not need to worry too much about this capacity as you will be well overloading the payload of your vehicle before this weight capacity is a factory.
The Timbrens are going to be the highest rated weight capacity we have in a suspension enhancement option for you at this time. view full answer...
The etrailer brand # e98873 motorcycle carrier weighs in at just below 60 lbs, so with the bike installed you'll be sitting at about 360 lbs of tongue weight which is well within the tongue weight capacity of the hitch, and is under the 380 lb tongue weight limit mentioned by Toyota, so the carrier, the dirt bike and the hitch should work well together.
Here's a couple things you'll want to keep in mind:
• You'll want to center the weight of the bike directly over the shank of the carrier... view full answer...
Yes, I confirmed with Thule that the Thule Pulse L # TH615 will fit your 2021 Toyota Sienna if you have factory crossbars. Also, the Pulse L will fit your vehicle if you have raised factory rails, but you will need a crossbar system to mount the carrier.
For a great crossbar system that will mount on your raised rails, I recommend the Malone AirFlow2 Roof Rack - Aero Crossbars - Raised, Factory Side Rails # MPG216. The AirFlow2 is an amazing economical roof rack that will allow you to... view full answer...
With the Timbrens # TTORSEN04 installed on your 2013 Toyota Sienna I wouldn't worry about weight distribution for a tongue weight of only 250 lbs. If the dealer says your pop up shouldn't be used with a WD system too that's even more reason not to. view full answer...
While Toyota is somewhat correct that installing the Curt Trailer Hitch Receiver # C22UR on your 2021 Toyota Sienna will partially block the hands free lift gate sensor, it will not disable it.
You will just need to place your foot on either side of the receiver and move your foot in and out until you find the sweet spot for the sensor.
If you are planning on towing with your Sienna you will also need a vehicle wiring harness # TK69FR.
I included a link to the written instructions of... view full answer...
Yes it does! The etrailer Trailer Hitch Receiver # e98853 does fit your 2016 Toyota Sienna AWD van and is a great choice because it gives you a sturdy hitch with a concealed crosstube to make it as unnoticeable as possible.
I have added a link to the installation instructions as well as a video install for you of the etrailer Trailer Hitch Receiver # e98853.
To complete your towing package I also recommend a wiring harness and ball mount:
- T-One Vehicle Wiring Harness # 118498 (for... view full answer...
Yes, the Curt Trailer Hitch Receiver # C13105 will fit your 2017 Toyota Sienna.
If you meant the 2021 Sienna model instead then there was actually a hitch model change so you need the Curt Trailer Hitch # C22UR instead. This is essentially the same hitch, just with the correct spacing and mounting hole dimensions to match the newer 2021 model.
Attached are some installation videos for you to check out. If you let me know what you plan on using the hitch for I'd be more than happy to make... view full answer...