The Rhino-Rack Vortex Bars are slightly bowed in the longer bar options to help support the weight when applied to the center of the bar. Most manufacturers have this as a part of the aero bar design. If you want a more straight bar, then you will want to instead use the heavy duty bars like # Y01-120B-NT for the track system or # RB1375B-2 for just the crossbars. There are longer bars like # RB1500B-2 and # RB1650B-2 if desired. view full answer...
Yes, we do have the Curt Trailer Hitch Receiver # C46DR which is made in the USA for your 2022 Nissan Pathfinder. Do note that while the receiver is made in the USA some of the mounting hardware may be imported.
The T-One Vehicle Wiring Harness # TK58VR will provide you with a 4-way flat connector. This connector is needed for the lights on most small trailers you might tow as well as with Auxiliary Lights # C53201 with any hitch mounted accessory that impairs the view of your vehicle... view full answer...
Most of the gooseneck hitches we have available, like the B&W # BWGNRK1104 or the Draw-Tite # 9465-37 are constructed of steel, but not stainless steel because it's strength relative to higher grades of steel. To my knowledge there is not a hitch that is made with 100% stainless steel components on the market, but most of the hitches do have some stainless steel components like the hitch ball or the safety chain loops.
When it comes to the best available gooseneck hitch on the market,... view full answer...
The etrailer Electric Trailer Brake Kit item # AKEBRK-35-SA, you were looking at, are the correct replacement brake assemblies for your 2012 Forest River R-Pod 177.
These brakes are 10" x 2-1/4" and are made for 3,500 lbs axles. They are self adjusting and fit 13" to 15" wheels. The E-coated backing plates resist wear and corrosion and have a 4 bolt brake mounting pattern.
I have linked an installation video below. view full answer...
The body structure of the Ford hitch cover # CR-007F is automotive grade plastic. This hitch cover is designed to fit a 2 inch hitch opening. The shank has the correct hole spacing so the pin holes will line up. The istance from back of the cover face to center of hitch pin hole: 2-15/16". You can use this distance to verify the fit.
I have included a link to a video review for you.
To secure the cover and deter theft I recommend a locking hitch pin. Use the # e98880 for your 2... view full answer...
I had this part pulled just to check for you and the Namsco Wheel Covers - 16-1/2", 8-Lug Wheels # NA7165B0 are made of Stainless Steel. view full answer...
The etrailer brand brake assembles such as the # AKEBRK-7L-SA 12 inch self-adjusting trailer drum brake assembly are manufactured by AxleTech. We offer them as a less-expensive alternative to the Dexter # 23-458. view full answer...
The Chevy Bow Tie trailer hitch cover # PC002207 is all metal so none of it is plastic and should hold up much better than any plastic hitch cover. To secure the hitch cover and deter theft I recommend a locking hitch pin # e98880. view full answer...
I definitely understand where you're coming from but since this is a soft cover the "Diamond Plate" on the Adco RV Propane Tank Cover for Dual 20-lb Tanks # 290-2712 has to do with the color as opposed to any kind of texture design.
Adco is the manufacturer and the etrailer sticker that you're seeing is only there to help prevent misuse of the photos our photo department works hard on. The tank cover you receive will not have that sticker on it.
Attached is a review video of the Adco... view full answer...
Yes, the Replacement Screws for Rack'Em Fitz-All Enclosed Trailer Ladder Rack # RA-28Screws are stainless steel.
These screws will replace all the screws for the Rack'Em Fitz-All Enclosed Trailer Ladder Rack # RA-28 view full answer...
The Wesbar 5-Pole Flat Connector W002290 (along with virtually every other wiring harness we sell) uses full copper wire. Unfortunately the Wesbar W002290 is no longer available. We now offer the Optronics # A40W5B which is a similar 5-flat harness that also uses full copper wire. view full answer...
The Malone Profile18B Rooftop Cargo Box # MPG911 is assembled in the USA but the individual parts are made overseas.
If you're looking for something that is 100% made in the USA then I recommend checking out the Yakima SkyBox NX 16 Roof Cargo Box # Y95AV or the Thule Force XT XL # TH6358B. The SkyBox NX 16 is closer to the price point of the Profile18B but it only has 16 cu ft of storage while the Force XT XL is at a higher price point but has the same 18 cu ft capacity as the Profile18B... view full answer...
The BedRug Headliners for Jeep Wrangler Unlimited Hard Top # HLJK074DRK for your 2008 Jeep Wrangler Unlimited won't work with connect with a Velcro or hook and loop type material. This is essentially a thick foam with a nice looking cover that resembles carpet but isn't nearly as thick as the fibers on carpet would be.
If you're needing to use a Velcro-type connection then you'll need to find a different way to connect that product to your vehicle. Otherwise if you let me know what you're... view full answer...
This A-Frame Trailer Coupler w/ Round Jack Hole # CA-5280-RB is manufactured in China.
We do have similar options like the Buyers Products A-Frame Trailer Coupler w Jack Hole # 3370091595 and Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole # 12660-97SP that are both made in the USA if that is what you are looking for. view full answer...
The Dacromet-Coated brake calipers included with the Titan # T2HRCM10DAC Premier Disc Brake Kit do indeed feature stainless pistons and guide bolts. The exterior of the caliper and the rotors are Dacromet coated for corrosion resistance. view full answer...
The Westin Tube Steps mounting brackets are powder coated. They use the factory provided running board mounting holes in the rocker panels. I have checked the install instructions for the Dee-Zee and the Pilot Automotive Tube Steps offered for your vehicle, they all mount in the same manner. GM trucks use the body mount bolts as an attachment point, but Dodge uses the rocker panels.
Westin states that their tube steps have a 300 pound weight capacity, which should be plenty strong enough... view full answer...
The wire making the connections has a copper conductor, and the pins are made of brass, for strength and corrosion resistance, also because it readily conducts electricity. The blades on the vehicle side of the connection are meant to fit tightly against the pins in the plug which helps hold the connection together. The cover on the socket also helps hold the plug in place, as well. view full answer...