The Hopkins 4-pole trailer wiring harness kit # HM43315 that you mentioned fits the 1993 Toyota pickup and also the following vehicles:
1989 - 1992 Toyota Pickup
1996 - 2004 Toyota Tacoma
1995 - 1995 Toyota Tacoma 1995.5 Mid-Year model
1993 - 1995 Toyota Pickup excluding T100
The other part you referenced, Tekonsha T-One Vehicle Wiring Harness # 118379 also fits your pickup and the following other vehicles:
1989 - 1995 Toyota Pickup
1989 - 1992 Toyota Pickup
1998 - 2004 Toyota Tacoma
1996... view full answer...
RV style hitches can be bolted or welded on your Winnebago frame whereas most vehicles will have mounting holes preset for trailer hitches. I wouldn't recommend using a vehicle trailer hitch. The Curt hitch # 13086 you referenced is a confirmed fit for your 1992 Toyota pickup.
For your motor home, the most likely hitch to fit is the Curt adjustable width trailer hitch receiver # 13703. It's a Class-III hitch and can be adjusted from 22-72 inches in width. It will have a gross trailer weight... view full answer...
Yes, the Detail K2 Rampage II Snowplow part # K2RAMP8219 can be used on gravel. I spoke to my contact at Detail K2 and they informed me that the 2-3" lift on your 1989 Toyota Pickup will not be a problem while using this snow plow.
The plow has an adjustable electric winch that allows you to operate it from in the cab or with the wireless remote. The skid shoes let you adjust plow height to scrape over gravel and uneven surfaces.
In order to mount this plow to your vehicle, you will... view full answer...
You need the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle. part # AL88113. It is a combination of an air lift spring and a jounce spring. It provides progressive support, the more weight you carry the stiffer the springs become. The air springs can be adjusted independently. Please keep in mind the Air Lift LoadLifter will not increase the maximum load weight of your vehicle. This item can also be paired with an air compressor so you can... view full answer...
I would recommend to use the Draw-Tite T-One Wiring Harness, # 118379, on your 1992 Toyota Pickup. This will give you the correct harness for your vehicle with a 4-pole flat connector at the rear of your vehicle. This harness will plug in behind the drivers side taillights and passenger side taillights.
On your trailer you can remove the 4-pole flat vehicle end connector that is on there now and attach the Hopkins Quick Fix(TM) 4 Pole Flat Trailer End, # HMC20031. This will give you a... view full answer...
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118379 is a confirmed fit for your 1992 Toyota pickup. With the turn signals working and emergency lights working but the running lights not working, the issue most likely is in the ground wire of your trailer.
Here is how to troubleshoot. Use a circuit tester like # PTW2993 to check the pin function on each of the 3 power pins on your 4-way when the trailer is not connected. The running lights will be the brown... view full answer...
For starters, you will want to turn the vehicle on and test the running light circuit (brown wire) on the vehicle's 4-way with a circuit tester like part # PTW2993. If power is present, then you know the problem in on the trailer. If power is not present, then you know the problem is on the vehicle.
If the error is on the vehicle side, then you will first want to start by checking the fuse box to see if any fuses associated with the trailer or running lights are blown. If not, you can... view full answer...
We have several light bar roof mount kits that are confirmed to fit your 1993 Toyota Pickup, but for a setup that uses the part # CARR210341 that you referenced you would want the # CARR220051 as well. view full answer...
Yes, I checked with Bestop and the Bestop 2-Piece Soft Doors # B5177415 have been confirmed to fit your 1972 Toyota FJ40 with a hard top.
I attached a set of installation instructions to the right for you to check out as well. view full answer...
For your 1981 Toyota Pickup you will need to first determine whether or not you have combined or separate taillight circuits. Combined taillights are ones that the blinkers and brake lights are on the same circuit. Separate means the taillights circuits are on different bulbs. Which either way you would want the Curt Circuit Protected wiring harness part # C59496.
This harness can work on either taillight style, the only difference will be how you install the harness on your vehicle. The... view full answer...
The "etrailer" you see on the mirror face of the # KS70003T that you referenced is just a sticker we put on products when we take pictures of them to discourage other companies from using our pictures. If you ordered this mirror the odds you get the one with the sticker are very low but if you did it would peel off easily.
You could back the hardware out as needed like you mentioned as well. view full answer...
The replacement lid for your vent is part # CAM40153. I have attached a photo sent in by customer who purchased this lid and has the same hinge style that you have. view full answer...
Air Lift SlamAir kit # AL59102 is the one you will want to use on your lowered 1992 Toyota Pickup. It is designed if the measurement from the leaf spring stack to the frame is 8.5 inches or more. Since you are right at 8.5 inches this is the kit you will need. view full answer...
We have a harness that can work for your 1994 Toyota Pickup.
First, the Tow Ready 17499-204 didn't have much information about it online, so I couldn't determine if it is compatible with your vehicle. The information I did find did not allude to being compatible with your truck.
When it comes to wiring your vehicle, it's best to stick with something that is built for your vehicle. That's why I recommend the Curt T-Connector, part # C55379. This is a confirmed fit for the '94 Toyota Pickup... view full answer...
In regards to the Curt 2 to 3 Wire Tail Light Converter part # C56196, you will need to install diodes part # RM-690 between the trailer tail lights and converter. The "out" side goes to the tail light and the "in" side goes to the converter. There will need to be one diode on each circuit for a total of six. view full answer...
To install a larger 13 inch tire and wheel combo like the Kenda Karrier # AM31952, you will need to get more room for the wheels. With your current tire having a diameter of 21.9 inches and a width of 5.6 inches, these would be quite a bit larger having a diameter of 24.1 inches and a width of 7 inches. You want to keep the side wall of the tire and the wall of the fender somewhere around an inch or inch and a half, but this is not as important as the height. You want to have a minimum... view full answer...
If you are going to purchase the Curt Hitch # 13086 for your 1985 Toyota Pickup, the hitch will be able to withstand the 2,100 pounds of your boat (along with the trailer as long the combined weight does not exceed 5,000 pounds or whatever the max tow weight capacity rating is for your 1985 Toyota Pickup). From my research, it looks like the weight rating of your vehicle is 3,500 pounds. However, in order to know for sure, I recommend consulting your owner's manual for that capacity. As... view full answer...
The Curt # C55379 taillight converter/trailer wiring harness is a fit for your 1991 Toyota Pickup, and is compatible with both incandescent and LED trailer lamps, so it'll work perfectly for you.
I've linked to a product description video for you. view full answer...
I spoke with my contact at Curt and found that the distance from the top of the side brackets to the top of the hitch receiver tube is 9.8 inches. I made a picture showing this for you. view full answer...
This could be a ground problem. A bad ground connection can cause all sorts of problems. First check the trailer connectors on the vehicle and on the trailer for any dirt or corrosion and clean them out. Corrosion can also build up behind the connectors where the wires attach.
On the vehicle side, make sure that the main ground is attached to a clean bare metal surface on the frame. On the trailer side connector, again make sure that the main ground is attached to a clean metal surface.
Use... view full answer...
Go To Results