Expert Answers about Toyota Pickup
- RV Trailer Hitch For a Class-C 21 Foot Winnebago
- RV style hitches can be bolted or welded on your Winnebago frame whereas most vehicles will have mounting holes preset for trailer hitches. I wouldn't recommend using a vehicle trailer hitch. The Curt hitch # 13086 you referenced is a confirmed fit for your 1992 Toyota pickup.
For your motor home, the most likely hitch to fit is the Curt adjustable width trailer hitch receiver # 13703. It's a Class-III hitch and can be adjusted from 22-72 inches in width. It will have a gross trailer weight...
view full answer... - 1993 Toyota Truck Light Bar Mount Recommendation
- We have several light bar roof mount kits that are confirmed to fit your 1993 Toyota Pickup, but for a setup that uses the part # CARR210341 that you referenced you would want the # CARR220051 as well.
view full answer... - Trailer Wiring Harness Recommendation for a 1981 Toyota Pick Up 4x4 and LED Trailer Lights
- For your 1981 Toyota Pickup you will need to first determine whether or not you have combined or separate taillight circuits. Combined taillights are ones that the blinkers and brake lights are on the same circuit. Separate means the taillights circuits are on different bulbs. Which either way you would want the Curt Circuit Protected wiring harness part # C59496.
This harness can work on either taillight style, the only difference will be how you install the harness on your vehicle. The...
view full answer... - Air Bag Helper Springs for a Lowered 1992 Toyota Pickup with 8.5 Inches Between Springs and Frame
- Air Lift SlamAir kit # AL59102 is the one you will want to use on your lowered 1992 Toyota Pickup. It is designed if the measurement from the leaf spring stack to the frame is 8.5 inches or more. Since you are right at 8.5 inches this is the kit you will need.
view full answer... - Parts Needed to Upgrade to a Larger Trailer Tire
- To install a larger 13 inch tire and wheel combo like the Kenda Karrier # AM31952, you will need to get more room for the wheels. With your current tire having a diameter of 21.9 inches and a width of 5.6 inches, these would be quite a bit larger having a diameter of 24.1 inches and a width of 7 inches. You want to keep the side wall of the tire and the wall of the fender somewhere around an inch or inch and a half, but this is not as important as the height. You want to have a minimum...
view full answer... - Troubleshooting Trailer Blinkers that Only Work When Brakes are Applied
- This could be a ground problem. A bad ground connection can cause all sorts of problems. First check the trailer connectors on the vehicle and on the trailer for any dirt or corrosion and clean them out. Corrosion can also build up behind the connectors where the wires attach.
On the vehicle side, make sure that the main ground is attached to a clean bare metal surface on the frame. On the trailer side connector, again make sure that the main ground is attached to a clean metal surface.
Use...
view full answer... - Can Replacement Converter for Parallax/Magnetek Fit to Replace Series 6300 Model 6332
- A 35 amp converter like the # PD4635V will work just fine to replace a 32 amp converter. We've seen several people use this to replace the converter you have now without issue dimensionally.
The buzzing you are experiencing is not going to come back.
view full answer... - What Backup Camera/Monitor Do I Need for the Factory Wiring on my 2018 Keystone Montana
- If my memory serves me correctly, the 2018 Keystone Montana came pre-wired with a backup/observation camera mount; the camera, monitor, and data cables would then need to be purchased separately. This is the case for all trailer's that came prewired for a Furrion backup/observation camera system. Therefore, in order to obtain these components you would need the Furrion RV Observation Camera System part # FOS43TASF for the 4.3" screen or part # FOS05TASF for the 5" screen. In order to add...
view full answer... - Base Plate Kit and Parts Recommendation to Flat Tow a 1982 Toyota Pickup with Front Leaf Springs
- Since the Roadmaster base plate kit part # 1123-1 that you referenced has been confirmed to fit 1982 Toyota Pickup Trucks that are 4 wheel drive and have front leaf springs it would work well for you.
If you check out the install instructions link I attached you will see that the tow hook of your vehicle will need to get removed and the base plate kit attaches to the bottom of the frame.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,...
view full answer... - Trailer Wiring 4-Way Recommendation for 1984 Toyota Pickup
- Sounds like you are looking for a 4-way for your 1984 Toyota Pickup. For that we have the Curt Kit part # C59236 that is a fit for your truck although it is a universal fit kit. You will need to test the wires of your taillights and then wire this kit accordingly.
view full answer... - Recommended 4-Way Flat Wiring for a 1995 Toyota Pickup
- Yes, a tail light converter would be required to wire your 1995 Toyota pickup for towing. We offer custom-fit T-connector # 118379, which would plug right into your factory connectors behind the vehicle tail lights.
I would recommend that you double check the trailer plug, however, as it is common that boat trailers use a 5-Way plug, due to being equipped with hydraulic brakes. If this is the case, you would also need a 4 to 5-Way adapter for your pickup, like part # 20036. The adapter...
view full answer... - Are Mirrors # CM17095 and # CM17195 Matching, Include Gaskets, and Fit 1989 Toyota Pickup
- Yes, yes, and yes.
The part number # CM17095 and # CM17195 are a matching pair of chrome mirrors, they come with gaskets, and they both fit your 1989 Toyota base model pickup truck.
I attached a review video for you to check out as well.
view full answer... - Can Hopkins Tail Light Converter Kit Be Used for Combined Tail Lights on Motorcycle
- Yes, the Hopkins Tail Light Converter Kit # HM48895 will technically work to take the separate circuits on your bike and combine them so that the stop/turn signals are carried along the same wire for use with your 3-wire tail lights. You would need to cut off the 4-Way connector and hardwire that end to the new tail lights.
A better option though is going to be with the Roadmaster Brite-Lite Wiring Converter # RM-732, as it wouldn't require any modifications and is really designed specifically...
view full answer... - Recommended Trailer Hitch And Wiring Harness For 1994 Toyota Pickup Truck
- I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver, part # 75031 for your 1994 Toyota pickup. This is a Class lll hitch and it has a 2-inch receiver opening. This hitch will not fit the T100 model truck.
Per the instructions, the bumper and bumper brackets need to be removed so you actually have less work to do when installing this trailer hitch.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with...
view full answer... - Base Plate Recommendation for a 1985 Toyota Pickup 4x4
- As long as your 1985 Toyota Pickup 4x4 has front leaf springs the Roadmaster Classic Base Plate Kit # 1123-1 would be the correct base plate kit for you.
If you do not have front leaf springs you would want a Roadmaster XL Base Plate Kit # 1146-1.
There are several other components needed for a flat towing setup also. You will need tow bars, safety chains, lighting, and supplemental braking.
If you do not have a tow bar I would recommend you get a RoadMaster Sterling All Terrain Tow...
view full answer... - Will the SMI Stay-IN-Play DUO Supplemental Braking System # SM99251 fit a 1991 Toyota Truck
- I spoke to my contact at SMI and he informed me that the SMI Stay-IN-Play DUO Supplemental Braking System # SM99251 that you referenced can basically fit any vehicle so it would work well on your 1991 Toyota Truck.
I attached an install video for you to check out as well.
view full answer... - Recommended Trailer Hitch for a 2020 Kia Sportage
- The trailer hitch I recommend for a 2020 Kia Sportage is the etrailer Hitch part # e72TR. The etrailer Hitch offers a complete bolt-on installation with no cutting/drilling or special tools involved therefore no permanent modifications are required. This is certainly something you can install at home, in your driveway without much effort as it only takes most on average around forty minutes or so.
This Hitch has a concealed cross tube so the only part that is visible will be the receiver...
view full answer... - Does Yakima Outdoormsan 300 Fit 1994 Toyota Pickup
- Yes, the Yakima Outdoorsman 300 ladder rack part # Y01136-Y00409 that you referenced is a confirmed fit for your 1994 Toyota Pickup truck's bed.
We have confirmed this with Yakima. This does not require drilling into the truck bed either.
view full answer... - Timbren Rear Suspension Enhancement Recommendation for a 1986 Toyota Granville Motorhome
- I spoke with my contact at Timbren, and he informed me that you would want to use the Timbren Rear Suspension Enhancement System # TTOR2002 that you referenced on your 1986 Granville Motor Home with a 1 ton rear axle.
I attached installation instructions for this product for you to check out, and you can view some additional information on suspension enhancement systems at the included link.
view full answer... - Truck Bed Bike Rack Recommendation for a 1986 Toyota Pickup
- I may have an option that will work for you, but I do not believe the Topline Truck Bed Bike Rack will work with your truck. It was designed for truck bed walls with an inside lip.
Instead, I recommend looking at a bike rack like the Thule Insta-Gater Pro, # TH93VR. This is a wheel mount bike rack that also does not require a lip.
I have attached video reviews for each of these bike racks for you to check out.
view full answer...
Go To Results