You are correct that the 2" mentioned in the description of the Westin Outlaw Nerf Step Bars # 58-54085 is for the diameter of the pipe surrounding the tread, or plate. The complete width of each Outlaw Nerf Step Bar is 4-3/4". I confirmed this with my contact at Westin.
Please note that this is designed to fit a 2019 Ram 1500 with the Crew Cab. If you have a different cab length or vehicle please let me know and I'd be happy to let you know what Outlaw Nerf Step Bars fit your vehicle. view full answer...
I checked with Aries, the manufacturer of the AdvantEdge Nerf Bars w/ Custom Installation Kit # AA2556049 and the entire weight of the unit is 57-1/2 lbs.
The bars weigh 34-1/2 lbs while the brackets weigh 23 lbs.
I have added a link to the installation instructions for this nerf bar and install kit, which is a fit for a 2019 Ram 1500 Crew Cab. view full answer...
I attached the dimensions for the tent part # SAR024 that you referenced. Sorry for any confusion but they call the length 10 feet but I would probably call that width like you too. The "width" then would be 6 feet with the height being 6'6". view full answer...
When installing the Curt fifth wheel rail kit part # C16306-204 in your 2017 Ram 1500 with a short bed you'll want the rear rail edge to measure 29 inches from the rear edge of the truck's bed.
Once you have that rail placed you'll then use the fifth wheel hitch to place the front rail. Basically you locate the rear rail where it needs to go and then set a fifth wheel hitch in the rear rail and then use the mounting tabs of the hitch to place the front rail.
This ensures that the hitch... view full answer...
The Air Lift 1000 Heavy Duty Air Helper Springs # AL60828HD have a height of 12-1/2" and width of 6". These are designed to fit the 2019-2022 Ram 1500. The Firestone Coil-Rite Air Helper Springs # F4175 fit select years of the Volkswagen Atlas, Beetle, Jetta, Passat, Lincoln MKC, and Nissan Rogue. These are not interchangeable.
It looks like you have a 2019 VW Atlas. If that is the case, the only custom fit option is the # F4175. If you have a 2021 Ram 1500 then the # AL60828HD would... view full answer...
Your Reese 15K Classic 5th wheel hitch head will fit the Reese Square Tube Slider # RP30048. Per Reese they have not changed the mounting hole dimensions for their 5th wheel hitches. The front to back bolt holes are 4" on center for this slider and each side bracket is 3" wide at the mounting holes.
The hitch will drop into the industry standard rails at the 20-1/2" wide by 22" front to back mounting locations.
I have attached a picture that will help you see the measurement points. view full answer...
Yes, it will. The Custom Wiring Adapter for Hayes Brake Controllers item # HA81795-HBC will allow you to connect the Hayes Syncronizer Trailer Brake Controller item # HA81725 to your 2016 Ram 1500. The harness plugs in to the factory connector located above where you right leg would be as you're sitting in the driver's seat. view full answer...
This is a good question, but the overall weight capacity of a vehicle does not increase necessarily when going with stiffer springs like with the part # SSC-51 that you mentioned. You do get additional suspension support which means the suspension would sag less when carrying weight that still falls within the capacity of the vehicle but since overall weight capacity is based on several other things like frame strength, brakes, transmission, wheels/tires, cooling system, etc. you don't... view full answer...
Using an extender such as the Brophy # ST18 might be possible, but it will depend on the tongue weight capacity of the hitch on your truck. Using the extender will lower the hitch weight capacity by 1/3, so you'll want to find the ID label on the hitch which lists it weight distribution towing and tongue weight capacities. If 2/3 of the hitch towing and tongue weight capacity isn't less than the 360 lb tongue weight of the trailer, then using the extender would be okay.
If the trailer's... view full answer...
For your 2017 Ram 1500, I recommend the Curt Custom Fifth Wheel Installation Kit item # C16444-204.These are made in the USA and fit all models and bed lengths of the 2017 Ram 1500's with or without a diesel engine.
The Curt item # C16444-204 rails are industry standard which means they are compatible with your Curt 5th wheel hitch along with most 5th wheel hitches on the market. The brackets are custom fit and install in pre-existing holes in your Ram's frame.
I have attached an installation... view full answer...
The Ventline Exterior Wall Vent part # V2111-55 measures to be 11-1/2" long x 5-1/4" tall. I have attached a photo that shows these dimension for you as well. In order to install this vent you will need sheet metal screws like part # 31071 and silicone sealant like part # 0160297. view full answer...
The Husky Center Line Weight Distribution Sytem # HT32217 comes with a shank that has an overall length of 12 inches. I've attached a diagram with some other important measurements for you. Measurements at the top are when used with the trunnion system. Measurements at the bottom (A-F) are the overall measurements. view full answer...
It is often possible to swap out just the weight-rated parts of a weight distribution/sway control (WD/SC) system when you change trailers, meaning the spring bars. The shank, head and frame brackets can often be re-used. Shanks do carry weight ratings, which should be observed, of course, but heads and frame brackets do not have specific ratings.
But before you buy any new bars you will want to confirm the R-Pod's actual measured tongue weight (TW) when you have it fully loaded for a... view full answer...
As long as the tongue weight of your 3,000 lb boat trailer doesn't exceed the 500 lb tongue weight rating of the Draw-Tite # 65062 then this will work great for your 2016 Ram 1500.
I recommend using a cover like the Draw-Tite QSP # 63080 or Skid Shield # 6771 to help protect the front receiver when not in use. If you use the skid shield then I also recommend using a locking hitch pin like part # e98880 to help deter theft. view full answer...
The lift brackets of the Brophy Tripod Camper jacks part # CJ41 extend out from the upright mast the same distance as the feet of the tripods. So as long as the camper extends out past the tires like you said yours did this would work although clearances would be pretty tight for you since it's only 1 inch. view full answer...
Since hitch extenders cut the capacity of the hitch they are installed in by 50 percent a better solution would be a longer ball mount like the # EA40 which is 14-5/8 inches from pin hole to ball hole and would most likely give you the extra clearance you'd need to be able to lower your tailgate when towing and not hit the trailer jack. view full answer...
The Dexter EZ Flex equalizer part # K71-655-00 was designed to work with the standard 1-3/4 inch wide leaf spring. Your current equalizer distance of 7-3/4 inches from one hole center to the other is a match for this kit and means it would fit and work well. view full answer...
The Yakima HD Crossbar # YA34FR measures 60" from end to end including the endcaps. Yakima does also make this bar in a large 68" version # Y01158 and an extra-large 78" version # Y01159 if you're interested as well.
Additionally, the t-tracks run the entire length of the crossbar, is 13/16" wide, 1/4" tall, and has a 3/8" opening. view full answer...
The Yakima HoldUp EVO Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount # Y02479 has a 13-1/2" distance from the center of the hitch pin hole to the closest part of the rack so you would not be able to fully lower your tailgate while the rack is in the hitch of your 2015 Ram 1500. view full answer...
Go To Results