Hi Hank,
It unfortunately looks like there aren't any custom-fit front mounted trailer hitch receivers for your 2003 Nissan Frontier so the next option would be an adjustable-fit weld on hitch. We offer a few different drops to help get the receiver tube under the fascia so you'll need to do some measuring from the frame to determine the drop needed.
Draw-Tite
7" Drop # 41990-07
16" Drop # 41990-16
Curt
3" Drop # 15901
9" Drop # C47CR
10.865" Drop # 15902
11-1/2" Drop # 15903
18" Drop... view full answer...
Yes, the Redarc brake controller install harness part # RED39FR does fit your 2023 Nissan Frontier without the towing package and would be what you would need to install a brake controller like the Redarc Tow Pro Liberty part # RED24FR. view full answer...
Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is measuring the amount of suspension sag the vehicle has with the tongue weight of the trailer on the hitch ball and then adjusting the spring bars until the rear suspension sits at the same height it did before the trailer was put on the hitch ball. view full answer...
I would start by checking each connector on your T-One Vehicle Wiring Harness # 118266 to ensure that you don't have any bent or damaged pins or any debris in the connectors. If not and all connectors are fully connected together then you'll want to test the 7-way to rule out that the wiring harness is the issue.
I've attached a wiring diagram below which you can use to identify the prong/wire functions. If the functions on are correct on the 7-way on your 2020 Nissan Frontier then we... view full answer...
Yes, the # DT65RR includes the 6 bolts, flat washers, and lock washers required to install the # 75282 on your 2022 Nissan Frontier. view full answer...
Hey Stephen,
Tailgate seals like the TrailSeal Tailgate Gasket # 834532001583 are universal fits so it really just comes down to style of the gasket in my opinion. This seal has a flat surface which I find typically makes great contact with tailgate but if you ever get anything sticky on it will annoy the hell out of you sticking to the tailgate and start to pull away from the bed. I've also seen this bit when it's extremely hot out with other seals and I'm personally not a fan.
I'd... view full answer...
Hey George, with the Reese weight distribution system part # RE94FR you can back up with the spring bars installed only if you are going to be basically backing up in a straight line. If you are going to jackknife the trailer at all though the bars do need to come off. view full answer...
Since you have a 169" canoe I recommend using the Erickson Over-The-Cab Truck Bed Ladder Rack # EM07707 on your 2018 Nissan Frontier because it will support up to about 130" of the length of your canoe. This leaves you with about 20" of canoe at the front and rear of this ladder rack.
I would imagine that 20" of space at the back of your Frontier would leave you with enough turning room for a travel trailer but if you would rather not have the canoe sticking out at all at the rear you... view full answer...
I went to our warehouse and took these measurements off the Draw-Tite Max-Frame Trailer Hitch Receiver # 75186. All the measurements are from the center of hole to center of the next hole. For the width it is 39-3/4" on center. Starting from the rearmost holes when it would be on the vehicle they are 2" on center, 5" on center and 3" on center.
I have also linked the installation instructions for this receiver near the bottom of the page since not all of the mounting holes are used for... view full answer...
The Curt # C17332 Short-Arm distance from the center of the trailer ball to the approximate center of the frame mounted chain hanger would be about 28-3/8 inches, so it'll just fit in the 2-3/4 inch space you have available. The system is designed for trailers with a loaded and ready to tow tongue weight below 600 lbs. The trailer ball is not included, for a 2-5/16 inch ball, you'll need # 19286 or # A-90 for a 2 inch ball. view full answer...
Hi Rene; I'm sure it's frustrating to have the mirror fall off, and while there are only universal towing mirrors for your 2016 Nissan Frontier, there are better ones than the clamp-on (which I also do not like). I would definitely go with the K-Source:
- K-Source Universal Towing Mirrors # KS3891-2
These have clips which go over the top and bottom of your mirrors, and then you tighten the strap around the mirror to get it as snug as possible. Now, is there still going to be some vibration?... view full answer...
The Inno Truck Bed Cargo Rack # INRT102-65 you found is going to be the only rack we have that sits as low for your 2022 Nissan Frontier. For an Aero bar like the Rhino Rack # RR56VH these are going to sit much higher on the bed. view full answer...
Yes, you are going to be able to use the Kuat Transfer V2 Bike Rack # KU64FR with your 2022 Nissan Frontier as long as you have a receiver. If you do not have a receiver from the factory you can use our etrailer Trailer Hitch Receiver # e98869 to carry the bike rack.
Anytime a receiver is put on a vehicle I recommend also adding the Wiring # 118266 in the event you ever need to pull a trailer or use Auxiliary Lights # C53201 with your truck. view full answer...
Hey John,
The factory harness will be located underneath and left of the steering column, taped to another harness near the emergency brake pedal. To install the Redarc Tow-Pro Elite Brake Controller # RED44FR you were looking at you'll need the Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers # RED39FR.
I've attached a video below that Brad made when he was installing the # 3050-P that will show you where the connector is as well. view full answer...
Timbren recommends a 1" gap when the Timbren Rear Suspension Enhancement System # TTORTUN4L is installed. The overall height of this kit is 4.6" so the distance between your leaf spring and the point of contact where the old bump stop hits should be 5.6". It doesn't have to be perfect, but the greater the gap the longer it will take to engage. It is possible to add spacers to close the distance using the 1/2" # TA25722-90P00 and 1" # A25723-90AH00. Adding spacers will require longer bolts... view full answer...
Hey George, the Westin Molded Running Boards # W63VX really do not drop down at all, since they are made to be flush with the body of the vehicle. If you are looking for a step that drops down a bit, we do have one good option for you, the Westin HDX Nerf Bars # W37PF. These are cab-length nerf bars with built in hoop steps. The steps themselves crop down about 4" and each step has a stainless-steel traction plate. I know they do not drop down the full 6" you were looking for, but this... view full answer...
The Blue Ox Pole Tongue Weight Distributing Hitch Adapter # BXW4023 is supposed to work with any over the frame style WDS, but since you're using the Blue Ox TrackPro Weight Distribution w/ Sway Control # BLU55FR you'd want # EQ95-01-5950 instead. view full answer...
Yes, the Curt Trailer Hitch Receiver # 13241 will fit your 2024 Nissan Frontier crew cab Pro/4. I recommend installing the T-One Vehicle Wiring Harness # 118266 with this so you have a 7-way connector. You could replace the end connector for the 7/4-way # HM40975 or use an Adapter # PK12716 for smaller trailers that use a 4-way flat. view full answer...
Go To Results