The ski and snowboard racks we offer are not designed to hold the ski poles as well but they can be used in such manner, you would just want to bump up to the next size. Since you mentioned that you had trouble closing the latch on your previous carrier, I recommend using the Yakima FreshTrack Ski and Snowboard Carrier part # Y03093 because the latch can be secured at multiple points for the perfect amount of tension on the skis. This is shown in the review video I have attached for you... view full answer...
We can get your 2018 Mitsubishi Outlander set up for towing with a hitch and wiring harness, and let's go ahead and start with the hitch, and what you will need is the following:
- etrailer Trailer Hitch Receiver # e48KR
With the hitch set, the next thing you will need is the wiring harness, and there are two different harnesses for your 2018 Mitsubishi Outlander PHEV, with the correct one depending on if you have the Factory Tow Package or not.
- WITHOUT Factory Tow Package: Vehicle... view full answer...
Since you have the factory tow package on your 2018 Mitsubishi Outlander the trailer wiring kit you'll want is the T-One part # 118277. I recommend this kit because it plugs right into the factory trailer wiring connector your vehicle has at the rear of it and also because it has our most reliable converter box of all of the kits we offer. I attached an install video for this kit for you to check out as well. view full answer...
Since you have a 4-way at the rear of your 2004 Mitsubishi Endeavor you will only need a brake controller and the part # ETBC7 that you referenced to install the controller and have a fully functional 7-way at the rear of your vehicle. This will allow you to control the brakes of your trailer as well as put a maintenance charge on the battery of your pop-up.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller... view full answer...
For your 2019 Mitsubishi Outlander I highly recommend the Curt Class III Receiver Hitch # C13163. This custom hitch is going to line right up to existing holes in the Outlander's frame rails for a simple bolt-on (no-drill) installation.
The hitch itself will provide you with a 2" receiver and it features a 4,000 pound towing weight capacity along with a 600 tongue weight limit. It's assembled right here in the USA and all the needed hardware is included. I have attached an installation... view full answer...
For a 4-way wiring harness recommendation for your 2007 Mitsubishi Raider you would want the Curt T-Connector Vehicle Wiring Harness # 55323. I attached an install video for you to check out as well.
Now to convert this to a 7-way you will need the part # 37185. view full answer...
I have another option for you, but the rear rack will more than likely interfere with the arm of the Inno Tire Hold 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Tilting # INH120 that secures the rear tire.
Instead I recommend frame mount rack like the Swagman Chinook 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting - Frame Mount # S64683 which will hold your bikes by the frame, and will accommodate two bikes weighing up to 45lbs each with tires up to 3" wide. If your... view full answer...
For your 2018 Mitsubishi Outlander I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13163. This hitch has a class III rating with 2" receiver tube opening so it can be used with virtually any hitch mounted bike rack without issue. It is a bolt-on fit with no drilling or cutting required. view full answer...
The Derale Series 8000 Plate-Fin Transmission Cooler # D13503 that you referenced is a universal fit supplemental transmission cooler. As long as you have room for it in front of your radiator/ac condenser it would work just fine on your 2007 Mitsubishi Outlander. The dimensions of this cooler are 11" Wide x 8-3/4" tall x 7/8" deep. I attached an install video for you to check out as well.
It sounds like you are trying to replace your factory cooler with this one. While this isn't the... view full answer...
For your 2012 Mitsubishi Outlander with raised side rails that run from front to back I would recommend the Thule Aeroblade Edge Roof Rack part # TH7503-TH7503.
This will fit secure to the raised rails of your vehicle and will provide you with an OEM looking roof rack that will be very quiet.
You will want to be sure you check the roof capacity of your vehicle that is listed in the owners manual of your vehicle and be sure not to exceed this figure with the weight of any roof cargo. view full answer...
In order to connect the lights on your trailer to your vehicle you will require a wiring harness. If you do not have LED tail lights, I recommend the # 119250KIT ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit. This wiring harness is a universal fit and will allow you to control the signal lights on your trailer.
If you do have LED taillights, I recommend the # 118538 T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector. This... view full answer...
If your 2017 Mitsubishi Outlander Sport roof has flush mounted rails that run front to back, I recommend the Thule Podium Square Bar Roof Rack. This system is confirmed to fit your vehicle and consists of parts # TH712200 for two 47 inch crossbars, # TH710601 for the foot pack and # THKIT4017 for the custom fit kit.
The square crossbars on this system will provide a 165 pound weight capacity. The bars themselves are 1-1/4 inches wide x 7/8 inch in height and will be compatible with your... view full answer...
Yes, the Curt Stabilizer strap part # 18050 can be ran to the bottom lip of a car's hatch if needed.
I attached a review video that shows it ran to the top of the hatch on a vehicle, but running it to the bottom would also work. view full answer...
For your 2022 Mitsubishi RVR the e63AR Hitch part # e63AR is the hitch you want that fits. It has great weight capacities and a very easy install as well. For trailer wiring you basically have two different options. Both options are universal wiring kits but the part # C59496 that fits requires splicing into the vehicle wiring whereas the ZCI kit part # 119250KIT instead uses sensors that attach to the vehicle wiring instead of requiring any cuts or splices for a much easier and less invasive... view full answer...
If your 2012 Mitsubishi Eclipse is a coupe, then the Malone Runway Trunk Bike Rack for 2 Bikes - Adjustable Arms # MAL84RR is a confirmed fit to carry up to 2 bikes on your trunk. Check out the video that I attached for you to see how this works. view full answer...
An anti-rattle hitch lock that uses a regular hex-head bolt should fit your Curt trailer hitch # 13581. Take a look at # SR25219. The head will be approximately 3/4 inches wide so measuring from the center of the hitch pin that would be 3/8 of an inch. If you have 3/8 of an inch from the center of the pin hole to the bar on your hitch then this lock would work.
Another option is to use a regular hitch lock such as # C23519 and a stand-alone anti-rattle device like # BX88224. view full answer...
The only hitch we offer for your 1990 Mitsubishi Montero is the Curt hitch part # 13091 which has a 1-1/4 inch opening. The only way to use a 2 inch hitch accessory with this hitch would be to use the hitch adapter part # HTAD.
Only thing about hitch adapters like this is that they cut the capacity of the hitch they are used on in half. view full answer...
Only the Curt hitches that aren't rated for use with a weight distribution system will have the stabilizer strap recommendation when used with a non-supported load like a cargo carrier.
The Curt hitch part # C13163 would not require the use of a stabilizer strap in any situation.
For a cargo carrier our most popular option is the Pro Series carrier part # 63153. view full answer...
We have the Tekonsha trailer wiring harness part # TK29VR that is a fit for the 2022 Mitsubishi Eclipse Cross LE and would be a really great option. It installs easily and has a very reliable converter box as well. view full answer...
According to Yakima, their ski and snowboard rack # Y03092 should fit the factory crossbars on a 2012 Mitsubishi Outlander. This economical roof-mounted rack holds 4 pairs of skis or 2 snowboards and uses Same Key System (SKS) lock cores to secure your gear to the carrier as well as the carrier to your crossbars.
If your Outlander still needs a roof rack, I recommend taking a look at the Rhino-Rack 2500 Series Roof Rack with Vortex Crossbars # RRVA137B-2, # RRRLKVA, and # DK228. This is... view full answer...
Go To Results