I can get you set up with everything you need to add a brake controller to your 2014 Mitsubishi Outlander. You were correct in starting with the 4-way like # 118482.
You will also need the Universal Installation Kit for Trailer Brake Controller # ETBC7, which will give you a 7- and 4-way trailer connector (which you will plug your trailer's 7-way into), circuit breakers and the rest of the hardware needed to install a brake controller.
As for the brake controller itself, I strongly recommend... view full answer...
I spoke with Thule and they were able to confirm that there actually are not any corresponding fit kits for the Traverse Feet and your 2017 Mistubishi Outlander with a slick roof.
With that being said, your only option is to upgrade your roof rack to a newer system like the Yakima CoreBar Crossbars # Y00421, with the SkyLine Towers for Yakima Crossbars # Y53TR and the Landing Pad 11 for Yakima SkyLine and Control Towers # Y00233.
This system will work with your bare roof, has a maximum... view full answer...
The replacement anode for your SW6DE water heater is part # CAM11563 while the replacement water heater element is part # CAM02143. The tool you need to remove the element is part # CAM09883.
Attached is a video showing how to remove your water element if you plan on doing this yourself. view full answer...
If you have a 2021 Mitsubishi Outlander that's a PHEV, the etrailer # e48KR is fit. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part # 118482, a # D-28 ball mount along with a # PC3 hitch pin and a trailer ball. For a 1-7/8 inch ball, use # 40038 or # 63845 for a 2 inch ball.
If you have an Outlander Sport, the Curt # C13079 fits all 2021 Outlander Sport models except for the PHEV. For a trailer wiring harness, use # TK67VR. You'd use the same ball mount... view full answer...
As long as your Outlander isn't the plug in hybrid (PHEV), I'd recommend the # 118482 for vehicles without the factory tow package or # 118277 for vehicles with the tow package. If your vehicle has the tow package, it will have the tow package electrical connector located behind the driver's side bulkhead in the cargo area, to the rear of the wheel well as shown in the provided photo. You could also call your Mitsubishi dealer with the VIN, and they should be able to tell you how the vehicle... view full answer...
I have a solution for you, but the the tires on your bike are 2.8" wide and the Swagman XTC-2 # S64670 can only accommodate tires up to 2.5" wide in the included wheel holders. You'll need swap the wheel holders out for the Swagman Fat Tire Bike Adapters # S64674 to allow your oversized wheels to seat comfortable in the holders. These adapters can house wheels up to 5" wide. view full answer...
We can help you with a hitch and trailer wiring harness for your 2018 Mitsubishi Outlander.
I suggest the 2-inch Class III Curt hitch # C13163. This hitch includes all required mounting hardware as shown in the linked video. Written instructions are linked for you too and these tell you exactly what tools you need to bolt on the hitch. No drilling is necessary.
For wiring use kit # 118482 if you do NOT have the towing package; use part # 118277 if you DO have the tow package. Install... view full answer...
I recommend the Kenda Karrier ST205/75R14 Radial Trailer Tire - Load Range C # AM10234. These Kenda tires are the same size tires that you're currently using, but are a radial tire, opposed to the bias ply tires that are currently on your camper.
Radial tires have a less stiff of a sidewall and are going to provide you with better ground contact, traction, stability, and tread wear. Additionally, because the plies of the tire do not overlap, they're less prone to heating up; heat is the... view full answer...
We have just what you're looking for. I recommend using the # C59496 because we've found that the converter boxes are a bit more reliable over time, so it's going to be a harness that can withstand the test of time. This harness will need to be hard wired into your tail lights, since there are no plug and play harnesses available for your 2014 Mitsubishi RVR.
If you don't already have a hitch and ball mount kit, I've added some recommendations for those below, as well.
Hitch: Curt # C13079
Ball... view full answer...
We have the Universal Installation Kit for Trailer Brake Controller # ETBC7 that will allow you to install a 7-way and brake controller on your 2018 Mitsubishi Outlander PHEV. I do not see an aftermarket option that is plug and play for your Outlander. You will be able to plug in the 4-Way # C59496 the dealer would have installed into the 7-way that comes with the kit. And run the additional wiring for the charge line and brake controller with the components that come with the kit.
I... view full answer...
It sounds like the connector on your 2010 Mitsubishi Outlander that you are referring to may be the one that mates with the wiring harness connector shown in the linked photo. This connector is part of the Curt custom-fit harness # C56102 and the Tow Ready # 118518, both of which fit your 2010 Outlander. Both of these wiring kits provide you with a 4-pole flat connector to activate your trailer's lighting functions. An installation video is linked for you. view full answer...
I checked with Rhino-Rack and the correct roof rack for your 1996 Mitsubishi Delica Van is as follows:
-Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 54" # RRVA137B-2
-Rhino Rack Gutter Mounted Legs - 8-3/10" Tall # RL210S2
-Track-Mounted Leg Adapters # RRVA-FK1 view full answer...
When it comes to carrying electric bikes on your Gulf Stream travel trailer using The Malone 2 inch Dual Purpose Hitch Receiver # MPG544 will reduce the tongue weight capacity of your hitch by 50 percent. Since your 2011 Mitsubishi Outlander has a tongue weight of 350 pounds it will drop down to 175 pounds.
I recommend putting The Adjustable Width Trailer Hitch Receiver for RVs, 22 inch to 66 inch Wide # C13704 on the back of your travel trailer. It is a bolt on style hitch that will... view full answer...
I spoke with my contact at Tekonsha and he stated that they have not tested the brake controller wiring harness on a 2006 Mitsubishi Raider. So, while it is possible that it will fit if the truck has a factory tow package that includes a 7-Way trailer connector, since it has not been tested I cannot say for sure if it will or not.
Instead, you can hardwire the controller. If the truck does not have a trailer connector, you will need to first install # 118323. I have included a link to... view full answer...
You are correct that your 20.5 x 8.0 x 10 sized tires are the same as 205/65-10 sized tires. With a 4 on 4 bolt pattern we have tire and wheel combinations that I've linked for you.
The highest weight capacity of our selection there is # AM3H460 and # AM3H470. They're the same tire on a different wheel. One being a white powder coat and the other is galvanized.
They have a maximum capacity of 1,650 pounds at 90 psi per wheel. view full answer...
There are 5 components that you will need to flat tow a vehicle behind a motor home. You will need a base plate kit, a tow bar, tail light kit, safety cables and a supplemental braking system.
It looks like you will be better off towing your Jeep rather than the Eclipse. After doing some research on your vehicles, it appears that there are no base plate kits available for your Eclipse. Base plate kits are the only component that must be vehicle specific. I spoke with my contacts at Roadmaster... view full answer...
In order to install a trailer brake controller like the excellent Prodigy P3 # 90195 in your 2002 Mitsubishi Montero Sport you will need an installation kit # ETBC7 and if you don't already have a 4-pole flat wiring harness on the Montero, one of those as well.
If you need a 4-pole harness you can use kit # 119178KIT from TowReady; I recommend this kit because it includes the circuit tester required for identifying the wire functions on the Montero. I have linked for you a video showing... view full answer...
When it comes to flat towing your 2018 Mitsubishi Mirage I recommend The Demco Kar Kaddy X Tow Dolly w/ Disc Brakes - Tilt Bed Frame - 4,800 pounds - Wide Tread # DM9713093.
The Demco Kar Kaddy has a maximum vehicle weight capacity up to 4,800 pounds. It is ideal for cars with front-wheel-drive with automatic transmissions. It has a tilting bed frame which allows for an easy loading and unloading of the vehicle.
The Kaddy includes a full LED DOT lighting package which includes the brake,... view full answer...
In order to make recommendations for brake assemblies and hub/drums, I'll need some more information.
I'm assuming your pop-up currently uses idler hubs. In order to recommend the proper brake assemblies and hub/drums, I'll need the reference numbers off of your inner and outer wheel bearings. To get the correct hubs with wheel bolt patterns that match your existing wheels, I'll need to know the lug bolt pattern of your existing hubs, which will likely be 4 on 4 or 5 on 4-1/2.
Once I... view full answer...
We do indeed have a hitch for your vehicle.
According to Curt, their # C13398 Class III hitch is a fit for all models of the 2020 Mitsubishi Outlander PHEV (plug-in hybrid), including the GT model.
If you'll be using the hitch for towing purposes, you'll also need a trailer wiring harness like # C59496 if the vehicle isn't equipped with the factory tow package or # C77KR if it IS equipped with the tow package. If you're not sure how your vehicle was equipped, your Mitsubishi dealer should... view full answer...
Go To Results