I have a different option for you, but the Curt Bumper Mount Hitch # C19031 only fits trucks with a step bumper and as such will not fit your 2008 Lincoln Town Car.
Instead you will need to go with the Curt # 13707 which is designed for your vehicle and will be perfect for carrying two bikes with a bike rack thanks to the 400lb tongue weight rating of this hitch.
If you do not already have a bike rack I recommend going with the Yakima RidgeBack 2 Bike Rack # Y02457 which will fit this... view full answer...
Draw-Tite trailer hitch # 41116 for your 2006 Lincoln Town Car does require removal of the dress panel for hitch installation.
On 2003 & Later Lincoln Town Car, it will be necessary to relocate passenger side exhaust hanger bracket as follows: Unbolt hanger bracket from vehicle frame. Remove rubber hanger from hanger bracket and tail pipe bracket. See Figure 2. Rotate rubber hanger and reattach to hanger bracket as shown in Figure 3. Do Not reattach to tail pipe bracket at this time.... view full answer...
The heat sink coolers like the Derale Dual-Pass Heat Sink Transmission Cooler, item # D13266, do not perform nearly as well as the traditional style coolers. These coolers have a single large cavity and do not force the liquid through a number of small cavities as a tube or plate and fin style cooler would. In comparison the heat sink style would not perform as well as the smallest plate and fin style transmission cooler.
For your Town Car I would recommend the Derale Series 8000 Plate-Fin... view full answer...
The trunk mounted bike rack I would recommend for you 2003 Lincoln Tow Car is the Thule OutWay part # TH45JV.
What makes this rack far superior to the others is the attachment system. It uses 2 rubber coated to attach to the vehicle rather than 6 nylon straps like other racks. This makes installation quick and easy.. It also includes locks to secure both the rack and the bikes to deter theft.
If you plan on carrying any women's or alternative framed bikes without horizontal top tubes... view full answer...
To install the Tekonsha Voyager Brake Controller # 39510 on your 1997 Lincoln Town Car, you will need to have a 4-pole trailer connector on the rear of your vehicle and then you will need to hardwire the brake controller with the Brake Controller 7 & 4 Way Installation Kit # ETBC7.
If you need to install a 4-pole connector on your vehicle you will use the Tow Ready Wiring Harness # C59496. This harness will tap into the tail light wiring. I am sending a link to the installation instructions... view full answer...
The part number you would need for ordering a replacement hardware kit for your Curt hitch part # C12130 is the part # RHK.
On the product page for the RHK you need to type C12130 in the "Hitch Number Box" and addit to your cart. Once purchased, we will ship you out the correct hardware. view full answer...
For a small trailer with only two lights, I would recommend hardwire kit part # C59496. It includes a tester and quick splices so you will have everything you need to find the right wires to tap into.
We have an installation video of a similar part being installed on a 1999 Ford Crown Victoria that should be helpful. I will add a link to it below. view full answer...
The stored depth of this step from the center of the front mounting hole to the back of the slide bracket measures 11 inches. The height of the step will be 7 inches when it is stored. I have attached diagrams showing these measurements.
To make sure this step will work for you, you will want to make sure that you have at least 11 inches behind the mounting location of the front bolt hole to install this step. As long as you have the 11 inches behind the front bolt hole, this step should... view full answer...
In order to find the distance from the center of the hitch pin hole on the Draw-Tite Max-E-Loader Trailer Hitch Receiver part # 41116-011 to the outermost edge of the bumper on your 2004 Lincoln Town Car you will need to measure from the pre-drilled hole in the frame (see photo) out to the end of your bumper. Once you have this measurement you will then need to subtract 22" as that will then give you your hitch pin hole to bumper clearance measurement.
Unfortunately, we have not yet had... view full answer...
The Curt hitch you referenced, part # C12130 will fit a 1980-2010 Lincoln Town Car. It will indeed fit both of your vehicles.
This being said, a hitch is not meant to be repeatedly installed and removed or swapped between vehicles. If it is removed and installed on a second vehicle, the manufacturer recommends using new hardware. A hardware kit can be purchased by ordering part # RHK, and typing "C12130" in the part number field.
For installation details, click the provided link. I have... view full answer...
Yes, all of the hardware needed for installation is included with Curt trailer hitch # C12130. If you plan on doing some towing you can use the nifty Curt Euro ball mount # C45592 for a 2 inch ball or # C45591 for a 1-7/8 inch ball. And for trailer wiring you can use # C59496 to add a 4-Way flat to the rear of the vehicle. view full answer...
I may have a solution for you, however there is not currently a roof rack system available that is compatible with your 2005 Lincoln Town Car.
To transport your kayak on your vehicle, I recommend looking at the Rightline Kayak Carrier with Tie-Downs # RL100K10 . This foam block kit will allow you to carry a single kayak on the naked roof (no crossbars or rails) of your Lincoln Town Car. The blocks will provide a safe surface for the vehicle and kayak, and tie-down straps are included... view full answer...
For your 1995 Lincoln Town Car, I recommend the Hollywood Racks Expedition 2 Bike Carrier, # HRF6-2. The Expedition bike rack is a trunk mounted rack that can carry up to two bikes weighing 35 lbs each.
The rack uses foam padding and straps to secure the rack to the trunk of the car. The mounting straps measure 67 inches in length giving you plenty of strap to mount the rack to the trunk lid of your Town car.
The rack arms include anti-sway cradles to prevent bike-to-bike and bike-to-car... view full answer...
When tire chains are installed we recommend not exceeding 40 miles per hour (lower if the speed limit is lower). Also, some vehicle owners manuals state a specific speed when chains are in place so you will want to look at the owners manual for your 2005 Lincoln Town Car.
When I searched for a 2005 Lincoln Town Car through our fit guide Thule chains # TH01594240 did not come up as a fit for tire size 225/60-17. I have included a link to the chains that do fit that size tire. If you have... view full answer...
Hey Lincoln, thanks for reaching out!
The two part numbers you were looking at were for two different Demco tow dollies which is why the pricing was that different for each.
According to my research the same fender is used for the Kar Kaddy X and the Tow-It 2 (which is what I believe you have) so you'll need the following:
- Driver Side # DM76MV
- Passenger Side # DM66MV view full answer...
There are 2 Class III receiver hitches available for your 2011 Town Car, the Draw-Tite Class III, part # 41116 and the Curt Class III, part # 13707. Both Hitches will work great for you.
Luckily enough, on your particular vehicle, the vast majority of the cross bar will be hidden behind the rear bumper structure, with a very small amount of the bottom of the cross bar and the receiver opening visible below the bumper.
Town Car models with the dual exhaust will require the removal and... view full answer...
By looking over the instructions for the Draw-Tite Trailer Hitch, # 41116, since the bracket already has to be rotated 180 degrees, also moving it to the outboard side of the frame rail may make it so that it will no longer be able to reach the exhaust that hangs from it. There may also be too much space between the hitch and frame with the hanger moved to the outboard side of the frame.
I have included a link to the installation instructions for you to view to give you a better idea of... view full answer...
Sounds like your ball mount has rusted so badly that it is stuck in the hitch you have on your vehicle. What you will first want to do is liberally apply a spray lube like WD40 or liquid wrench to the ball mount. If the back of the hitch opening is open spray some down in there, down the front of the hitch opening and also on the hitch pin hole.
Since you don't plan on using the ball mount anymore I would recommend taking a heavy hammer or sledge and hitting the ball mount into the hitch... view full answer...
We have everything needed to equip your 1999 Lincoln Town Car so that it can pull your boat trailer.
Starting with the trailer hitch, I recommend the Curt Class III Receiver Hitch # 13707. This Class III hitch is confirmed to fit your Lincoln Town Car and it features a towing capacity of 4,000 pounds. I recommend also verifying the capacity of your vehicle by checking your copy of the owner's manual. You will need to follow whichever capacity is lower, the vehicle's or the hitch's.
I... view full answer...
A hitch from a 1999 Lincoln Town Car will also fit a 2004 Lincoln Town Car. Since your 2004 has dual exhaust you will need to relocate the exhaust hanger. I attached installation instructions for the Curt Trailer Hitch Receiver # C12130 for you to check out that shows how this is done. view full answer...
Go To Results