It sounds like you may have an issue with the Receiver # LC305117 for the Linc Analog Remote # LC292614. Be sure to check the fuses in the receiver as well as the antenna wire for any damage. If you are not getting a click on the receiver after holding the momentary button on the receiver and the light button on the remote, Lippert recommended taking the batteries out of the Linc remote to let it normalize itself. view full answer...
The AC490TT-B part number you got from Keystone is for a center cap with a 4.9" pilot hole diameter. The Lionshead Trailer Wheel Center Cap w/ Snap-In Plug item # LHCS109-SI60C will fit. This center cap fits 8-lug wheels with a 4.88" to 4.9" pilot diameter. view full answer...
The 7,000 lb double-eye leaf spring we have that is closest to 26" is the 24-7/8" long 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles # e64SR.
Assuming yours have flattened a good amount (which will definitely be true if the trailer is older), these will work out as a good replacement. You mentioned hardware, and I'm assuming you were referring to U-bolts, shackle bolts and straps. You'll need to measure your shackle straps but you can use the following:
- U-Bolt Kit # APUBR-9
-... view full answer...
The mounting hardware will depend on what length shackle straps you need for the MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K # MR27ZR.
You can use either the MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps # MR46ZR or 3-1/8" Long Shackle Straps # MR76ZR. view full answer...
Hello Janet. That is actually a really good idea for a product. Unfortunately, MOrryde does not make any kind of rubber boot or cap to go on the feet of the steps. The idea is to protect the foot, keep them from getting scratched and increase friction, right?
I feel like coming up with your own rubberized protector would not be too hard. I have seen rubberized tape like "flex tape" at stores. I would cut a piece of that to fit the bottom and/or sides of the foot. This way the foot will... view full answer...
Yes, The Landing Gear Set w/ Handle # RVLG-8HDL will work with your 2010 Keystone Montana Hickory Fifth Wheel.
The landing gear has a durable, black powder coated outer tubes that has a zinc-finished inner tube that provides excellent corrosion resistance. It has a weight capacity of 8,000 pounds. The 12V DC Motor # LC142178 is sold separately.
I attached a review video link below. view full answer...
For your 2013 Keystone Montana Hickory 3100RL the best option for a hitch that has a 500 lb tongue weight capacity is the Curt Multi Fit Hitch part # C13704 which fits standard RV frame styles that are between 22 and 66 inches measured from outside to outside. view full answer...
There are two replacement motors for the electric stabilizer jacks, Replacement Electric RV Stabilizer Jack Motor part # LC138445 and Replacement Electric RV Stabilizer Jack Motor part # LC352338. In order to choose the correct replacement motor you simply need to note the color of the support arms. If you support are yellow then you need the Replacement Electric RV Stabilizer Jack Motor part # LC352338 but if the support arms are black then you need Replacement Electric RV Stabilizer Jack... view full answer...
The Keystone Montana is unique in that it has its own set of landing gear legs with three weld stops (tabs) instead of two, and the only option we offer for that is a set of replacement legs:
- Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear # LC178653
- Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear # LC178652
If you use the bottom-most weld stop (tab) you would have to go with these, however, the distance between the top weld stop and second-to-bottom... view full answer...
That's a great question.
The jacks sit in the 5th wheel frame mounted clips so that the tab on the upper end of the jack leg sits under the clip, and the tab on the lower end sits above the clip, as shown in the diagram on the right-hand side of the photo I provided.
The Lippert # LC178653 replacement lead leg has three tabs on it, and the spacing of the tabs is also shown in the photo. view full answer...
The part number 297697 is for a Dexter 7K axle.
There is a full bearing kit for this. It's part # BK3-200. It includes the bearings, races, and seals.
Of course, this is not a definite replacement as I could not find exact numbers for your axles. It's very likely that this is the right one, but you should still check the numbers of your current bearings, races, and seals to ensure they match this one's:
Inner bearing: 25580
Inner race: 25520
Outer bearing: 14125A
Outer race: 14276
Seal:... view full answer...
We do not have a handrail available in white. The closest option to white that we have available would be a stainless steel option like the Stromberg Carlson Folding Handrail # AC-544.
You could potentially look into painting the handrail white, but we do not have any that are already white. view full answer...
I can help you determine the right replacement leaf springs for your 2011 Keystone Montana, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as what you'll need to do is measure your current leaf springs from center-to-center of the spring eyes, and you also need to know the weight rating of your axle.
Leaf springs also flatten a bit over time, so you should go with ones that measure a bit shorter than what you currently have. For example,... view full answer...
The folks at SuperSprings tell me that ideally, you'd see about 1/4 inch of pre-load between the # TSS-107-40 spring and the underside of the trailer frame, but they tell even if there's no preload, the SumoSprings would still provide benefit. You can even trim the spring if you need to, but SumoSprings cautions that doing so will void the warranty. view full answer...
I went ahead and consulted the owner's manual for your Furrion RV Tankless Water Heater - Gas - Automatic Pilot # FR68SR, and this symptom is correlating with there could be lime scale forming due to precipitation of hard water.
To fix this, Furrion recommends that you decalcify your water heater. You're also going to want to ensure that your water heater is producing the minimum water flow of 0.32 gallons per minute.
If it's not, what you can try and do is if your unit is equipped with... view full answer...
I spoke to a contact at Progressive Dynamics, he confirmed the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 90 Amp # PD4590K18LS8 as a replacement for your 2011 Keystone Montana Hickory Fifth Wheel. view full answer...
For your 2011 Keystone Montana HIckory I recommend checking out the Furrion RV Tankless Water Heater # FR98SR. This is a tankless water heater that will provide on demand hot water so you can simultaneously wash dishes, do laundry, and take hot showers without hot and cold water fluctuations.
Also, this water heater has a 13,000 - 60,000 Btu heating capacity, and measures 12-5/8" wide x 12-5/8" tall x 19-1/4" deep. view full answer...
I don't know the length of the cable used for valves on your Montana so you'll want to measure the length to determine the correct replacement. To make the swap out easy I recommend just unbolting the old valve from the system and then swap in the new valve (without the flanges it comes with). This will make it a much faster swap out and prevent you from having to cut or glue any pipes. I've listed the sizes we currently offer below by cable length:
Black
36" # 34466N4AB36GM
48" # 34466N4AB48GMA
72"... view full answer...
It sounds like you do need a new motor, and Fan-Tastic roof vents will use the part you mentioned, the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00.
This is the only replacement motor for their fans, and is designed to be compatible with each of their models. view full answer...
For the Lippert 1716 pin box you might have the only cushioned Lippert pin box we offer is the Trailair part # LC158777. We don't have a FlexAir at this time but this cushioned pin box will give you a much smoother ride quality that what you have currently.
If you instead had a 1116 then you'd need the part # LC155943 instead.
The big difference between the 1116 and the 1716 is the overall length. The 1716 is a "long" pin box and measures 20-3/8 inches from the front row of bolts to the... view full answer...
Go To Results