Yes, you can up to three additional cameras to the Furrion RV Observation Camera System part # FOS05TASF. For the side of your trailer, I recommend using the Furrion Vision S Side Camera w/ Marker Light Bracket part # FCE48TASL which is also a built in marker light. If you wanted to add a camera to the vehicle as well then you can do so with the Furrion Vision S Rear Camera w/ Sharkfin Bracket part # FCN48TASF. view full answer...
Best option we'd have would be a multi-fit hitch like the part # 13703 which is designed for frames that are between 22 and 72 inches in width measured from outside to outside and fits all of the standard trailer frame designs. view full answer...
The best option would be the Westlake part # LHWL410 which has more than enough capacity for your trailer to utility it's full 15k capacity, has a high speed rating, and comes with a great warranty...not made in the USA , but it is made to USA specifications..
This tire is the the next size up from what you mentioned but the size difference is so small it won't be an issue. view full answer...
The Ventline Ventadome Trailer Roof Vent # V2092SP-28 would be a good replacement for your Valentine VD0433 roof vent.
The vent is 14-1/4 inches wide by 14-1/4 inches long. The vent has a simple, hand-operated crank that rotates to open and close the dome and eliminates the need for wiring.
The Roof Vent Installation Kit # 344270KITW is needed for installation.
I attached a review video link below. view full answer...
The Swagman e-spec bike rack you'd looked at, part # S94FR would be an outstanding choice for carrying 2 e-bikes weighing up to 70 lbs. You can lighten your bikes by 10 or so lbs each by removing the battery packs. The rack can accommodate bikes with tires up to 3 inches in width.
Before using the rack on the back of your fifth wheel, you'll want to defeat the folding feature by removing the folding pin and installing the supplied bolt, washers, and nut.
You will need to use an adapter... view full answer...
The diameter of the hole in the ceiling for the Valterra A/c Ceiling Register # A10-3358VP is 5-13/16". You'll also need a depth of right at 7/8" to accommodate the vent. view full answer...
The towing capacity of your 2009 Ford F-250 will remain unchanged through the life of the vehicle in the eyes of the manufacturer no matter what components are added. The suspension enhancements that you are referring to will certainly help with your vehicle's ability to support the added weight but again will not increase it.
Please note that when using a set of airbags on a truck that is also pulling a 5th wheel trailer you need to be aware of where the brackets mount for each. If you... view full answer...
We can help you out getting a new motor, and though there isn't a motor specifically for your 2010 Keystone, thankfully landing gear motors are essentially universal, so I recommend an option from Stromberg Carlson:
- Replacement Motor for Stromberg Carlson Electric Landing Gear # LG-142178
This is compatible with Stromberg Carlson, Atwood, Venture, and Lippert landing gear, which is the majority of the landing gear manufacturers. So you'll want to ensure you have one of those brands,... view full answer...
We have what you need to get a bike rack on the back of your 2019 Keystone Alpine, but there is no rack that is 5th wheel approved and is a 1-1/4". You can get another hitch or something like this # 3371804060 so you can use a 2" bike rack. These are the only size shanks that are approved to work with 5th wheels like yours.
Then you can get this RV Rider # HLY64FR bike rack. This is approved to work with your 5th wheel and has a capacity of 80 lbs per bike so it's fully capable of carrying... view full answer...
The SumoSprings Trailer Helper Springs part # SS26MV mount on top of the leaf springs directly above the axle so there should be no interference with the Lippert Center Point by Trailair Air-Ride Suspension Upgrade. view full answer...
The Bearing Buddy Bearing Protectors part # BB2717 are not threaded, they instead offer press-in installation. There are Bearing Buddy Bearing Protectors available which are threaded but not for a 2.717" bore. I have attached a full list of options below but you will need to verify the exact hub bore down to the thousandth of an inch to confirm. view full answer...
The auto leveling system on your 2017 Keystone Sprinter is a Lippert auto leveling system, so the stabilizers that I recommend are the JT's Strong Arm Jack Stabilizer Kit which are also by Lippert and confirmed to work.
If you have more than 58 inches between your front landing gear legs, then you will want part # LC191023. If you have less than 58 inches, then you will want part # LC191024.
You will also need the Adapter Lug, # LC314592, for the rear leveling legs. view full answer...
The closest RV step we offer to 27 inches in width is the Flexco triple step # SMFP-3200L that measures 27-1/8 inches in total width.
You might need the outriggers part # LC301704 to move the brackets out to install the steps if yours is 27 inches wide. view full answer...
I went out to our warehouse and measured the arms of the Surco ladder mount bike carrier, part # SP501BR. From the outer edge of your ladder to the furthest point of the rack is approximately 16 inches.
I've attached a picture to show the dimension as well. view full answer...
Since hitches for trailers are not necessarily custom fit you can simply filter through the linked page that has our selection of trailer hitches on it. You will just need to make sure that the fit specs for the hitch match up with that of your 2015 Keystone RV Cougar 279RK.
One of the most popular options is the Curt Adjustable Width Trailer Hitch Receiver # 13703 which is a Class III receiver that has a 2" receiver opening. This trailer hitch is compatible with trailers that ha a frame... view full answer...
Since hitch adapters cut the capacity of the hitches, they are installed in due to added length and leverage they are not recommended to be used with a bike rack like the part # S94FR. You would need a 2" hitch installed on your fifth wheel. Then you would have a selection of bike racks for your Montana. We would need the model number of your Montana to make a solid recommendation for you. view full answer...
According to my research your 2020 Keystone Alpine 3801FK should be using 26" leaf springs so the following will work with your setup:
- 4K Powder Coat # e22YR
- 4K Dacromet # e48SR
The powder coat option will be the same type of finish your current leaf springs have while the Dacromet finish has superior resistance. The Dacromet is better for boat applications but there isn't any harm in adding them to a standard setup either.
I do recommend verifying this length is correct with your... view full answer...
We carry the hub you are looking for with our part number 8-219-13UC3 and then for brake assemblies # 23-464 for the left hand side and # 23-465 for the right hand side. view full answer...
I highly recommend going with an Adco All-Climate + Wind cover. These have a Tyvek top cover which is the same material used to protect buildings that are under construction.
From the specs I could find on your 5th wheel trailer it looked like it was 40' long. For this you want the part # 290-34857 which fits fifth-wheels 37'1" - 40' long.
To ensure proper fit you simply need to measure your 5th wheel trailer from the front to the back (including bumpers, spare tire, and ladder - but... view full answer...