For your Roadmaster Falcon Tow Bar, there are two adapters that will work with your Blue Ox base plates. You can use either the Roadmaster Tow Bar to Blue Ox Brackets Adapter # RM-031 or the Blue Ox Base Plate Adapter Brackets for Roadmaster Tow Bars # BX88151.
The RoadMaster Nighthawk or Sterling Tow Bars to Blue Ox Brackets Adapter # RM-031-5 will not fit your specific tow bar. I've attached a help article to assist. view full answer...
A trailer wiring kit is to power the lights of a trailer. Since you're going to be using the Curt hitch, part # 13245, for a bike rack and not to tow a trailer you won't need a wiring kit, or anything else. The hitch includes all of the hardware for installation and that's all you need. To mount the bike rack you could need a hitch pin, like # PC3, but that depends on the rack. Many have specific pins that work with the rack and a universal one won't work. It's likely you already have... view full answer...
The Tekonsha # 20135 is specifically designed to be used on a 2005 Jeep Liberty with the factory towing package. If you are unable to find the port for this to connect to, you may not have the factory towing package. The only real way to confirm if you do have this package is to contact a Jeep dealer and have them run your VIN. They should be able to tell you right away if you do or do not.
If you do not end up having the towing package, you will need to start with a 4 flat, like the Tekonsha... view full answer...
Both the Tow Ready Custom Fit Vehicle Wiring for the 2008 Liberty by Jeep, part # 118381, and the Draw-Tite Custom Fit Vehicle Wiring for the 2008 Liberty by Jeep, part # 118554, will work on a 2008 Jeep Liberty.
The difference is that the #118554 is used on vehicles that do not have a tow package, and the #118381 is for Libertys that have a factory 7 way and want a way to have a 4 way connector as well.
If your Jeep Liberty does not have a tow package you will want to use the # 118554... view full answer...
The Roadmaster base plates, # 521434-1, will work with a Reese tow bar as long as it is Reese model 74950 and you use adapter # RM-025 with quick disconnects # RM-201. If it is a different model tow bar then it will not work. based on my research I found that the compatible Reese tow bar is only rated for 5,000 pounds so it is not likely the base plates will be compatible.
For a compatible tow bar you can use the Tracker # RM-020 and you will also need the quick disconnects # RM-201. You... view full answer...
The Derale Transmission Cooler you referenced, # D13503, is an excellent choice to protect the transmission of your 2005 Liberty, however it doesn't contain a fan.
If you are planning on really pushing your vehicle off-road at low speeds where getting sufficient airflow through the cooler might be a problem, you will be better off using a cooler with a fan, like part # D12742. The unit is 13-5/8 by 10-1/4 by 3-1/4 inch thick, so you would need enough space in your desired mounting location.... view full answer...
According to the Surco fit guide, the correct Safari Rack for your 2006 Jeep Liberty is the Surco Safari Rack 5.0 Rooftop Cargo Basket for Factory Rails part # SPS4550-1101 which is 50" long x 45" wide. The 60" long version may still work for you but unfortunately I cannot recommend you use it due to the surface area on the roof of your Jeep. The cargo basket will work well with your factory raised side rails and will not require crossbars for use.
In order to install either of the above... view full answer...
Yes, the Blue Ox Base Plate Kit # BX1119 for your 2003 Jeep Liberty is directly compatible and will work perfectly with your Blue Ox Aventa tow Bar.
This base plate assembly is confirmed to fit your Jeep and it features hidden reinforcements and removable bracket arms for a clean look when you aren't towing. I have attached an installation video and the written instructions that you can also use for reference. view full answer...
The industry standard a-frame trailer tongue jack mounting pattern is 3" on center. The jacks we offer for this standard like the Lippert Power Stance Electric Trailer Jack part # LC89VR have slotted mounting holes so they will work even if the dimensions are slightly askew but you may have to enlarge the holes slightly if they don't quite match up. This would be the case for nearly all jacks since they use the same industry standard mounting pattern. view full answer...
Yes, Curt hitch # 13245 is designed to fit around the under vehicle spare tire on 2009 Jeep Liberty 4x4 models.
The installation is very straight forward as well, as you can see at the link to the installation instructions I have provided.
If you need to wire your vehicle for towing, you can use custom fit wiring harness # 118554, which would also be a simple install for you.
The recommended ball mount for your vehicle is part # C45030, which you could secure using a hitch pin like... view full answer...
The CIPA Clip-On Towing Mirror, part # 7070, is a universal fit item so it is designed to fit virtually every vehicle side view mirror. The arms and straps are adjustable to accommodate a wide variety of mirror shapes and sizes. Just make sure there is a rim or lip around the mirror so the tow mirror arms have a place to clip. view full answer...
The Roadmaster Even Brake Portable Supplemental Braking System # RM-9400 with serial numbers below 27497 is not inferior to the ones with a serial number higher than 27497. Roadmaster switched their circuit board manufacturer at this point.
If you have an older RoadMaster Transmitter with your Even Brake pre 27497 you will need to get the RoadMaster Even Brake Transmitter and Receiver # RM-9430.
For the Even Brake newer than 27497 you will only need the Transmitter # RM77FR view full answer...
Since the Yakima EvenKeel Boat Saddles # Y04052 will fit crossbars with a maximum width of 3-1/2 inches and the maximum thickness is 1 inch, it will fit the crossbars on the Malone AirFlow2 Roof Rack - Aero Crossbars - Raised, Factory Side Rails # MPG216. view full answer...
I checked with Roadmaster and you can use the Bulb and Socket kit, # RM-155. This indicates that there is room in the tail light housing on your 2012 Jeep Liberty for the extra bulb. I have also a link to all of the flat towing FAQ articles we have for reference. view full answer...
According to Roadmaster the StowMaster series of Tow Bars, like RoadMaster StowMaster Car-Mounted Tow Bar, # RM-501, are compatible with the EZ style of base plates like # 521434-1 (installation details linked below) that you have referenced. I have included a link to the installation details and a video review of this tow bar below. view full answer...
The Adventurer tow bar, # BX7322, may only be used with base plates that have a 16 inch to 36 inch spaced removable tab width. Using Blue Ox base plates # BX1122 on your 2006 Jeep Liberty you will have a width of 20 inches which is within the range of the tow bar.
This tow bar is rated for 5,000 pounds. Once loaded your Jeep Liberty could potentially weigh more than this given that the curb weight of the vehicle is listed at about 4,000 pounds depending on the model. You will need to stay... view full answer...
Because the floor in front of the driver's seat of the 1st gen Jeep Liberty isn't completely flat, a portable braking system like the # HM39524 Brake Buddy wouldn't be the best choice for your vehicle.
I'd recommend a supplemental braking system from Demco like # SM99251 if the motorhome has hydraulic brakes or # SM99243 for motorhomes with air brakes. You'll also need the # RM-88400 relay is required to prevent the towed vehicle's brake signal from overriding the turn signal from the... view full answer...
The Curt Trailer Hitch for the 2006 Jeep Liberty, # 13044, will fit on your 2006 Jeep Liberty Renegade with the fuel tank skid shield.
The fuel tank skid shield will need to be temporarily removed or loosened for installation. The tow hooks do have to be removed. Our notes on that hitch showed those instructions, but I also called our supplier (Curt) and they did verify those notes.
I am sending a video link of this hitch being put on a Jeep Liberty with the skid shield and it will show... view full answer...
Anytime you are going to haul cargo on the roof of a vehicle, you do need to find out the weight capacity of your roof. You can check the owners manual or contact the car dealer for the roof weight capacity that is allowed for your 2004 Jeep Liberty.
The SportRack Roof Cargo Carrier, # SR7018, attaches to the crossbars of the roof rack, that run from side to side. It will work on Thule square crossbars, round crossbars, and most factory crossbars up to 4 inch diameter. The cargo carriers... view full answer...
The Curt T-Connector # C55382 you referenced would be the correct harness for your 2006 Jeep Liberty so long as it did not come with a factory 7-way. I have included a link to an install of this harness on an '06 Liberty for you to take a look at. If your Jeep does have the factory 7-way you would need T-One Harness # 118381.
As for the lights, Standard Trailer Light Kit # TL29BK is going to work for your application as well. I have included a link to a video install of this kit for you... view full answer...
Go To Results