I do have options for you but the Curt Trailer Hitch Receiver part # 13432 is not a confirmed fit for a 2018 Jeep JL Wrangler. Instead, you will want to take a look at either the Curt Trailer Hitch Receiver part # C13392 or the Draw-Tite Max-Frame Trailer Hitch Receiver part # DT78MR.
The above two options are both direct bolt-on fits that have a Class III rating with a 2" receiver tube opening. I recommend using the Draw-Tite Max-Frame as it is currently the more cost-effective option.... view full answer...
Yes, the Air Lift 1000 Air Helper Springs # AL60829 will work on your 2018 Jeep JL Wrangler with a 2.5" lift. The kit will come with a few smaller spacers. Depending on what kind of lift kit you have, an additional 2" spacer may be needed. For that you can use part # AL52420. view full answer...
We have a good solution for you. While the one you have looked t isn't going to work out you can use the Roadmaster Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars - 3/4" Thick part # RM-035 to get the job done. Your D rings aren't exactly standard sizing but if you'll use these with the included circle spacers (in pic) it will be a nice and secure attachment and you won't have to worry about the looseness that typically causes issues in this type of setup.... view full answer...
Yes. You could use the Roof Rack for Jeep JL Soft Top - Square Bars - Steel - Black # ER74FR with the hardtop off; it's actually designed to be used with the top off so it sounds like it's the perfect solution for your 2018 Wrangler JL. You will need to remove the bars to put the hardtop back on, but if you ever decide to get a soft top then you can put it on over these bars. It's really a pretty cool solution! This rack will connect to the windshield housing and the speaker roll bar area. view full answer...
The crossbar, # 910021-00, is not required when using the Nighthawk tow bar, # RM-676, with MX, MS, or EZ5 model base plates. So if your 2018 Jeep Wrangler is the new JL model and you are using base plates EZ5 OR if it is a JK model and you are using # RM-521448-5 or # 1444-3 then you will be good to go without the crossbar. Any other model, EZ, EZ2, EZ4 or XL, and the crossbar is required.
The EZ5 for the 2018 JL is # RM-521453-5, or you will need to use the crossbar and baseplates #... view full answer...
We do have a Curt T-Connector that fits a 2018 Jeep Wrangler JL but the part # C55124 that you referenced does not fit.
Instead you need part # C56407 which tees in behind your tail lights and then draws power directly from your battery via the included black wire. The great thing about drawing power directly from your battery is that your vehicle wiring is completely protected in the event that something goes wrong with your trailer wiring.
Attached is an installation video of this wiring... view full answer...
Yes, # RM-676 and # RM-521453-5 are compatible with your 2018 Jeep JL Wrangler.
Both the Roadmaster Universal Hy-Power Diode Wiring Kit # RM-152 & # RM-154 are compatible with your vehicle. However, if you already have a 4-way at the rear of your vehicle, you can use # RM-154 to plug in the premade 4-blade to run to the front of your vehicle, or if you do not have a 4-blade at the rear, you can use # RM-152 to add one.
The braking system, the Demco SBS Stay-IN-Play DUO Supplemental... view full answer...
The Roadmaster Battery Charge Line for Motorhomes part # RM-156-75 is 30 feet long. It Includes 12-gauge wire, split wire loom, circuit breaker, and hardware view full answer...
The only spare tire bike rack we offer for the 2018 Jeep Wrangler JL is the Hollywood Racks SR1 2-Bike Carrier - Spare Tire Mount Item # HRSR1 and there is no ski rack that is compatible. If you are willing to go the hitch mounted direction, I recommend the Yakima FullSwing 4 Bike Rack - 2" Hitches - Swinging Item # Y02465 with the Yakima HitchSki Snowboard and Ski Carrier for Hitch Mounted Bike Racks Item # Y02418.
The ski rack requires at least a 4 bike carrier. The rack holds 6 pairs... view full answer...
The Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar w/ LED Lights # RM-676 is a great choice for flat towing your 2018 Jeep JL Wrangler. It has a non-binding design which makes disconnecting a breeze on any terrain and a large hookup radius to make connecting to your base plates easy on any terrain as well. It has LED lights to help you hook up or disconnect in the dark and comes with a 6-way to 7-way cable and safety cables so you won't have to purchase them separately.
To flat... view full answer...
I spoke with Brad, one of our installers here that's done quite a few Invisbrake installs, and he stated that box under the front driver seat is tucked in further than you'd think so you'd have to purposefully kick it and it wouldn't be an accident.
That being said, it is possible to mount the compressor box in the back of your Wrangler but you'll most likely need to get some additional 1/4" nylon vacuum line to go from the box to the brake booster in the engine compartment and also some... view full answer...
Tekonsha's Fit Guide confirms wiring harness # 118786 as a fit for your 2018 Jeep JL Wrangler. You can double-check before ordering if you like by comparing the included photo that shows one of the harness' custom connectors to the connectors at your Wrangler's tail lights. Installation should take about an hour or less and you can refer to the linked wiring installation article and video for guidance.
I recommend adding protective wire loom # 459075-1 to your install; this is sold by... view full answer...
The Roadmaster Crossbar-Style Base Plate Kit # RM-521424-4 is not confirmed to fit your 2018 Jeep JL Wrangler, it is for a different generation of Wranglers with the factory bumper in place.
Most aftermarket bumpers have D-ring bumper mounts, and there are adapters to hook the tow bar directly to the bumper. However you will need to check with the manufacturer of the bumper to see if it is rated to tow with. If the Bumper you have is rated to tow and you have 3/4" d-ring mounts you can... view full answer...
Yes, the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118786 is perfectly compatible with LED lights.
This harness is a fit and work great on a 2018 Jeep JL Wrangler Sport S without the factory tow package. I have added a link to an installation video of this part for you to check out as well. view full answer...
The compatibility of the Curt Premium 4 Bike Rack for 2" Hitches part # C18064 with your 2018 Jeep JL Wrangler will largely be dependent on two factors, what trailer hitch you have and what size spare tire you have. The Curt Premium 4 Bike Rack part # C18064 measures 10" from the center of hitch pin hole to closest edge of carrier. If you were to use the Draw-Tite Max-Frame Trailer Hitch Receiver part # DT78MR with a factory spare tire then the Curt Premium 4 Bike Rack would clear by bout... view full answer...
Yes, the T-One Vehicle Wiring Harness part # 118786 will work on all 2018 Jeep JL Wranglers with factory LED and incandescent lights. This is actually an updated harness that was made to replace the T-One Vehicle Wiring Harness part 118782 that had issues with certain packages. There will be no issues whatsoever using the T-One Vehicle Wiring Harness part # 118786 on your 2018 Jeep JL Wrangler Rubicon. view full answer...
While you can certainly carry bikes with your 2018 Jeep JL Wrangler, there are no spare tire bike racks that will work with a back-up camera, so the best thing to do is use Draw-Tite Max-Frame Trailer Hitch # DT78MR and a hitch-mounted bike rack. When bikes are loaded they will block the view of the rear-view camera, of course, but you can remove the bike rack or there are racks available you can leave on and simply fold the upright mast down.
For that I strongly recommend the Saris Freedom... view full answer...
In order to determine if the Swagman # S64650 XC bike rack will work on your 2018 Jeep Wrangler, you'll need to measure the horizontal distance rearward from the hitch pin hole to the furthest rearward point of the rear mounted spare tire. If this distance is less than 10 inches, the rack will work well for you. I'll link you to a help article that describes exactly how to take this measurement.
An optional locking hitch pin/cable lock is available as part # S64031. I've linked to demonstration... view full answer...
The RockyMounts WestSlope 3 Bike Rack - 2" Hitches # RKY10223 you linked to has a distance of 10-1/2" between the closest part of the rack and the center of the hitch pin to give you enough room for your spare tire. Its versatile design fits most bikes regardless of frame design, suspension, or brake style and tiered mounting positions optimize bike spacing. It has a weight capacity of 40lbs per bike. Ratcheting hooks hold your bikes securely by the front wheels and ratcheting wheel straps... view full answer...
You can use the Blue Ox Patriot part # BLU37TR on a motor home a jake brake. This system doesn't have to integrate with any braking components on the motorhome since it uses an inertia sensor so it can be used on basically any braking system. view full answer...
Go To Results