The Dexstar Conventional Steel Wheel # AM20504 is a 6" wide wheel with 1/2" of positive offset, which give you a back spacing of 3-1/2". view full answer...
Yes, we do. To carry the Thule Hullavator item # TH898 on your 2021 Jeep Gladiator Sport, I recommend the roof rack by Rhino Rack and it includes the following parts:
Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 71" Long - Qty 2 item # RRVA180B-2
RLTP Leg Adapters for Rhino-Rack Vortex Aero Crossbars - Track Mount - Qty 4 item # RRVA-FK1-2
Rhino-Rack Roof Rack Legs - Gutter Mount - 4-5/16" Tall - Qty 4 item # RRRL110S5-2
These crossbars are 12" longer than the item # RRVA150B-2... view full answer...
The black air tubing on the Roadmaster BrakeMaster System w BrakeAway for RVs w Air or Air Over Hydraulic Brakes - Proportional Item # RM-9160 is 1/4" by 40' and the air hose that goes from the RV to the vehicle is 6'.
If you need more tubing you can get additional tubing by the foot with the Air Line Hose 1/4" for BrakeMaster Systems - Per Foot Item # RM450700. view full answer...
You are going to want to find a new truck or trailer to tow. The Draw-Tite Max-Frame Trailer Hitch Receiver # DR64FR while having a higher weight rating it will not increase your factory towing capabilities. Since the highest rated 2021 Jeep Gladiator is only allowed to carry up to 765lbs the trailer you are looking at exceeds the capabilities of the Gladiator. view full answer...
The Yakima OverHaul HD Adjustable Truck Bed ladder rack # Y01151-57 is adjustable between 19"-30" above the truck bed rails. I can confirm, as a fellow Jeep owner, that your soft top is going to be slightly taller than the hard top when installed. With that being said, the difference is negligible- on my JKU the difference is about 1-1/2" at the tallest spot between the soft and hard top (which is at the frame arms).
I was not able to find anything that says exactly how tall the tops on... view full answer...
Yes you are correct. The outer diameter of the Removable Xtreme Off-Road Swing-Up Trailer Jack # ARK57FR is 2 1/2" and the inner diameter is 2. view full answer...
The Kuat Pivot 2 Swing Away Hitch Extender part # PVD20B can be used with bike racks, cargo carriers, or any other 2" hitch mounted accessory for that matter. In regards to weight, you have a 250 lb limit so this will be the weight of the bike rack with bikes or the weight of the cargo carrier with cargo. That said, the adapter does reduce hitch capacity by 50% and weighs 46 lbs so this will need to be taken into consideration as well.
For example, if the hitch capacity is 600 lbs then... view full answer...
Each generator that comes with the A-iPower 3,800-Watt Portable Inverter Generators - 3,000 Running Watts - Gas - Manual Start # 289-SUA2000i-2 is 20" long x 19" tall x 11" wide. view full answer...
Tonneau covers are designed to distribute the weight evenly. So standing on a folding tonneau cover, even briefly, is not recommended. But if you need to stand on a folding tonneau, make sure it is a hard folding tonneau cover and only stand on it when it is doubled back on itself. This also has an added benefit. You are never standing on the top of the tonneau cover, only the bottom, protecting the top of your tonneau cover from any visual blemishes or scuffs. Please keep in mind you are... view full answer...
You are limited to the lowest-rated component for the towing capacity of your 2020 Jeep Gladiator Rubicon; the towing capacity of the Curt Trailer Hitch Receiver # CU74FR that fits your Rubicon is 5,000 lbs, so that is the capacity you will need to go with to safely tow. view full answer...
The SumoSprings Solo Helper Springs # SS62XR you were looking at for your 2021 Jeep Gladiator measure in at 5-1/2" tall and 3-3/8" wide as shown in the included diagram.
I included a video review of the # SS62XR for you to take a look at. view full answer...
For your 1" Timbren Spacer, part # A25723-90AH00, you will need a M10x1.5 Hex Cap Screw. As you said, it will need to be 5" long to accommodate the extra length.
You will need to source these from a local hardware store. view full answer...
The best base plate kit for your 2021 Willy's Jeep Gladiator is going to be the Roadmaster Direct-Connect Base Plate Kit item # RM-521453-5. This base plate kit has a concealed design that creates a factory look when you remove the arms. This kit is custom fit for your Jeep, and is made in the USA.
I have attached an installation video so you can see the process and what the final product will look like.
Some other parts you will need to flat tow your Jeep are listed below.
Tow Bar... view full answer...
The simple answer to your question is yes, the Draw-Tite Trailer Hitch Receiver # DR64FR that fits your 2020 Jeep Gladiator has enough capacity for the Jeep. This trailer hitch has a 7,500 lb towing capacity and 1,125 lb tongue weight capacity which is absolutely enough for the Gladiator.
The reason is, according to the owner's manual of the 2020 Gladiator, it has a 4,000 lb towing and 400 lb tongue weight capacity unless you have the Max Tow package. If so, those numbers are 7,650 lbs... view full answer...
The highest capacity hitch available for your 2023 Gladiator is the Curt Trailer Hitch item # C74DR. This hitch is custom fit and bolts to your Jeep with included hardware. It fits both the Rubicon models and standard models.
The Curt Trailer Hitch item # C74DR has a 7,500 lbs towing capacity and a 750 lbs maximum tongue weight which can be increased to 8,000 lbs and 800 lbs when used with a weight distribution system.
It sounds like you are planning on towing you will also need a wiring... view full answer...
From the ground to the bottom of the coupler for the Yakima EasyRider Double Decker Trailer # Y08129 it measures 16". To ensure that you tow the trailer level you just need to measure from the ground to the top of the inside of the receiver on your 2020 Jeep Gladiator and then choose a ball mount that has the correct rise/drop that matches up to the EasyRider. I have attached a link to a helpful article about choosing a ball mount that you can reference.
I tried to find what the height... view full answer...
To add a front hitch to your 2023 Jeep Gladiator, I recommend the Curt Front Mount Trailer Hitch item # C31086. This hitch is custom fit and bolts to your Jeep with included hardware.
Please note that this hitch will not fit the Rubicon and Mojave sub-models.
This front hitch has a 350 lbs capacity for mounting accessories and a 3,500 lbs gross trailer weight. The 2" x 2" receiver sticks out just below your license plate and does not affect your ground clearance.
I have linked an installation... view full answer...