I do have an option for you but they do not offer an aftermarket plug in trailer wiring harness for your 1995 Geo Tracker because it is just not that popular of a tow vehicle. Instead, the only way that you can install a 4-way trailer connector on your Tracker is with a hardwire kit for which I recommend using the Curt Circuit Protected Converter part # C56175.
The Curt Curt Circuit Protected Converter only requires four wires to be spliced into the vehicle so the install process is fairly... view full answer...
A tow bar isn't vehicle specific, so it will work with just about any vehicle that has a compatible base plate kit installed on it.
For a 1996 Geo Tracker 2 door, you'd want to use the Demco # DM9517023 base plate kit which is compatible with your tow bar. You'll also need safety cables like the # RM-643 if you don't have them already.
To wire the taillights so they operate in sync with those on the tow vehicle, I'd recommend a diode system like part # RM-154. The Blue Ox Patriot braking... view full answer...
Hardwire trailer wiring harnesses such as # C56175 will require using a circuit tester such as # PTW2993 to determine the functions of the taillight wires on your 1992 Geo Tracker. You could also use # 119178KIT which comes with a little circuit tester.
On these harnesses the red wire is for brake lights, yellow is for left turn, green is for right turn, brown is for taillights, and white is ground. After you verify the functions of the wires on your Tracker installation will be easy! view full answer...
In order to attach the Tow Ready Tow Bar, # 63180, to your Roadmaster base plates, you will need the Roadmaster Base Plate to Tow Ready Tow Bar Adapter, # RM-025. This will allow the two different parts to work together.
The Roadmaster Quick Disconnect Tow Bar Base Assembly, # 910021-00, is for Roadmaster tow bars so it should not be needed, just the adapter and tow bar listed above. I have included a link to the installation details for the tow bar for you.
Keep in mind that the Tow... view full answer...
As a general rule of thumb, trailer tires should be replaced every 6 to 8 years regardless of wear. Even though an older tire might appear to have plenty of tread left on it, dry rot and cracking can cause tire failure.
The mating surface behind the bolt holes should be flat, and should mate perfectly with the face of your hubs.
I would definitely replace the tires before using the trailer again. If the wheels are showing signs of corrosion, I would also recommend replacing them with... view full answer...
Since your 1996 Geo Tracker 4X4 does not have the jack storage compartment shown in the installation instructions, the trailer harness connector is likely to be located behind one of the tail light assemblies or one of the rear interior trim panels. This Hopkins harness, part # HM41245, fits both 2-door and 4-door versions of the Tracker.
Start on the driver-side and remove the tail light assembly. Please see the included photograph. This is the most-likely location for the connector.... view full answer...
The best towing bar wiring option for the 1994 Geo Tracker is the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267 which will give you a 6-way round at the front of your Tracker with a coiled cord that connects that plugs into the motor home's 7-way for a nice clean install. The Geo Tracker's lights will activate in sync with the motor homes lights. This is our most popular wiring option. I have attached an installation video for your reference.
You will also need... view full answer...
The Curt Trailer Hitch Receiver part # 11128 is indeed a confirmed fit for a 1992 Geo Tracker. It features a bolt-on install with no cutting, drilling, or welding required. This is a class I hitch which means the maximum number of bikes that can be carried is two, regardless of capacity. This has more to do with leverage than capacity. There are unfortunately only class I options for this vehicle.
The only way to safely carry more than two bikes would be on the roof with a roof bike rack.... view full answer...
We can help you with the wiring and other components required to ready your 1990 Geo Tracker for flat towing behind your Newmar RV. Safe and legal flat towing does require a few items and the three linked articles will give you detailed background to aid your selection. The basic components needed to flat tow include a tow bar, safety cables, a wiring/lighting kit of some type and base plates and a braking system for the towed vehicle. A high/low hitch adapter is also often helpful to keep... view full answer...
For trailer wiring for your 1989 Geo Tracker we have universal kits like the part # 119178KIT which are a confirmed fit. This brand is the most reliable of the options available for your vehicle though. view full answer...
Does the warning sound eventually go off if the door is shut on your 1996 Geo Tracker? If so that would save you the trouble of having to shut off power to those things to flat tow the vehicle. The Warning and Indicator lights use the fuse in location 8 in the fuse block located under the left side of the instrument panel. However this fuse is also for the ignition system, gages, and 4-wheel drive system. I am not certain that you could still flat tow the vehicle if there is no power to... view full answer...
I was unable to find much information on the P and E Tow-Me tow bar so I cannot say whether or not that it will work with Roadmaster or Blue Ox base plates. I did find one person who said that the attachment from the tow bar to the base plates matched the Roadmaster products but I cannot verify that.
What I recommend is to go ahead and get parts that you know will be compatible. Starting with the Roadmaster base plates, # 118-15, for an economical compatible tow bar you can use # RM-020... view full answer...
For starters, you'll need a base plate kit like # 118-3 which is a fit for 2 door Geo Tracker models only.
From the photo you provided, it appears you're missing the crossbar that the # RM-020 uses, unless you already have it an it just wasn't shown in the photo. A replacement crossbar is available as part # RM-025. The Tracker tow bar would typically be permanently installed on the vehicle, but it can be removed by removing the drawbars of the # 118-3. view full answer...
With the Roadmaster base plate kit part # 118-8 you actually will want to connect the safety cables like part # RM-643 to the frame of the vehicle so that in case of a problem with the base plate the cable would bypass that and connect to the frame and still be able to grab something. So look on the frame for an opening that you could snag the hook of the chain onto. view full answer...
You can get it from etrailer.com!
We've got exactly what you're looking for, part # RM-8603. The coiled cable will work great with the break-away switch used by your Hopkins Brake Buddy. view full answer...
The # RM-732 is the correct adapter to use to go from a separate taillight system like what you have on your motorhome to a combined system like what is on your tow dolly.
For wiring your motorhome with a 7-way you would basically want to follow the wiring directions that are on top of the converter. The right side of the converter is the input side so you will need to test the wiring of your RV with a circuit tester like part # PTW2993 to determine function and wire it accordingly. You'll... view full answer...
I have a possible solution for you but the trailer hitches for the 1991 Geo Tracker are Class I trailer hitches. All of the enclosed cargo carriers including those from Rola will only fit in Class II and/or III hitches.
What you can do is use a Class I rated regular cargo carrier such as # C18110 and then use a cargo bag such as # e98990. Then you could use Rightline cable lock # RL100640 to lock up the bag. It isn't exactly the same as a hardshell carrier but it will work! view full answer...
For Roadmaster base plates # 118-8 for your 2-door 1997 Geo Tracker you can use any Roadmaster tow bar.
The most popular tow bar is the Falcon 2, # RM-520. But if you were looking for something a little more cost effective you could use the Tracker tow bar to tow your Tracker, # RM-020. You will also need safety cables, # RM-643.
Next you will need lighting. I recommend going with a magnetic kit like # RM-2120 This kit will bypass the vehicle wiring.
And finally, most states now require... view full answer...
Yes, the connection point to add trailer wiring harness # 118372 should be the same on a 1998 and 1999 Chevy Tracker. The connection point is located in the inside of the drivers side tire jack compartment. The plug where you will connect the trailer wiring is just forward of the tire jack compartment. I have included a link to the installation details for you. view full answer...
The Custom Mounting Bracket Kit for SnowBear Hydraulic and Winter Wolf Snowplows # SB397-050 does have mounting holes, but is a confirmed fit for your 1992 Geo Tracker. view full answer...
Go To Results