We don't have the specific number but what I think will be more helpful for you is the distance from the rear most portion of the bumper to the hitch pin hole. Which for the # 41932 that dimension is 1-1/2 inches.
Check out the picture I attached that shows this. view full answer...
The hanger spacing needed for use with the # APT9 is 29-1/2 inches measured on center of the bolt holes. This works well with the equalizer since it's length (7-3/4 inches) is split on each side of the equalizer.
When you add half of the equalizer to the length of your spring (25-1/4 + 3-7/8) you end up right at 29-1/4 inches which would work out perfectly. view full answer...
Yes, it will. The B&W Custom Installation Kit w/ Base Rails item # BWRVK2503 does fit your 2008 GMC Sierra 1500. It is custom fit for all three of that models bed lengths including your 6-1/2' bed. This set of rails is industry standard so they will also work with your Pro Series 16,000 lbs hitch.
I have linked an installation video below.
To make towing with a 5th wheel easier I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 10' Long item... view full answer...
I went out to the warehouse and pulled the Bully Black Bull LED Hitch-Mounted Step, part # BBS-1104L, and took some measurements for you. Take a look at the image of the dimensions and the video I made for you at right.
From the last pin hole closest to the step, to the step itself the measurement is 3-1/8 inches. The measurement from the last pin hole to the end of the step where the LED is measures 6-1/2 inches.
Check out the video review of this Hitch Mounted Step I have included at right. view full answer...
To determine the measurements you were looking for, I went into our warehouse and measured the Stromberg Carlson Scissor Jack # JSC-24-IND. The spacing of the small, circular holes on the outer edge is 1-1/2 inches. The diameter of the hole is 5/8 inches. The spacing of the larger rectangular holes is 2 inches x 1-3/4 inches. The diameter are 7/16 inches wide by 3/4 inches long.
I have provided a graphic showing all the dimensions. view full answer...
I spoke with my contact at Curt, and the U-bolts included in the # C113 replacement hardware kit for the Curt Quick Goose 2 measure 3-3/4 inches long by 2-5/8 inches wide. The inside width is 1-1/2 inches. The threaded portion of the bolts measures 1 inch long. view full answer...
Thank you for asking your question about the dimensions of the Putco Boss Grille Insert # P270510B which fits your 2009 GMC Sierra 1500.
I contacted my technical representative at Putco to obtain the grille's dimension and we will add these to our product page for other customers.
The grille measures 41.03-inches wide x 11.82-inches tall.
I will send you a separate email with the written installation details from Putco. view full answer...
The Pro Series carrier # 63153 weighs in at about 55 pounds. And even lighter than that we have Curt aluminum carrier with steel shank # C18100 which weighs 29 pounds. view full answer...
I went out and took some measurments for you and found that the Replacement Steering Pin and Clip for Roadmaster Tow Dollies # RM-357100-00 is approximately 5-1/2 inches long (4-1/2 inch usable length) by 5/8 inch diameter. I have included a few other helpful measurements as well in the attached photo.
This is designed to fit Roadmaster # RM-2000-1 and # 2050-1 tow dollies. view full answer...
When using the Equal-i-zer Weight Dist Shank - 12" Long - 13" Rise, 9" Drop - 600 to 1,400 lbs TW # EQ90-02-4400 the holes on the shank are spaced 1-1/4" apart center on center and the lowest adjustment is 9" of drop-which would be the lowest set of holes. The next set of holes up would be 7-3/4" drop, then 6-1/2" drop and so on. view full answer...
The first thing I suggest is to confirm the combined weight of your two kayaks; this will allow you to verify that the truck's roof has the needed capacity for that weight load plus that of a roof rack and rack-mount kayak carrier like the multi-kayak Thule Stacker # TH830. Using this single carrier might help with the total weight since it handles up to 4 boats but weighs only about 8-lbs. You can then compare this to the roof weight capacity noted in your GM owner's manual.
Roof racks... view full answer...
Weight distribution systems can be fitted with differently-rated spring bars to allow them to work well with varying trailer tongue weight (TW). The ideal is that your fully-loaded trailer's actual measured TW (we offer a scale # e99044) plus the weight of any cargo behind the rear axle of the tow vehicle together will fall in the middle of the bars' weight range.
I linked our main page for all Equal-I-zer brand spring bars which are available for TWs from 400- up to 1400-lbs. For example,... view full answer...
The Stromberg-Carlson 4000 series tailgates including # VGM-99-4000 are not rated to carry any weight so they do not have a capacity. Specifically they say "This gate is not designed for weight bearing applications. DO NOT stand on this gate."
The 100 series, # VGM-99-100 for a 2006 GMC Sierra, has a 100 pound capacity. view full answer...
The Karrier ST175/80R13 Radial Trailer Tire With 13 Inch White Wheel, Item # AM31985, has a speed rating of 81 mph. This tire and wheel combo has a maximum weight capacity of 1,610-lbs at 65 psi.
We recommend staying within the speed limits of the areas you are traveling. You always want to keep the tires inflated to their maximum pressure so that you have a safe and secure ride. view full answer...
I went out to the warehouse to take a measurement and found that the bumper bolt holes on Curt hitch # 13322 measured roughly 5-1/2 inches apart center-to-center. I've added a photo for you to take a look at which has these dimensions displayed. view full answer...
The dimensions of just the jounce spring itself of the SumoSprings Solo Custom Helper Spring Kit # SSR-610-40 are 4 inches tall x 3 inches in diameter. These dimensions are without the included bracket and with the spring under no pressure. The # SSF-201-47 is 2-3/4 inch horizontal and 3-1/4 inch vertical. view full answer...