We have a Westin bumper in black that is a fit for your 2008 Ford E-350 with the part # 20107, but the part # 61001 that you referenced does not fit your van. view full answer...
First of all, yes part # C16427-204 is the correct bracket kit for your 2015 Ram 2500 and the rails as well as the hardware is all included.
It can be installed with a spray in bed liner, I've linked a video of a 2017 Ram we did with a bed liner for you. With that being said we've got some reviews from customers who have said the bolts are sometimes more difficult to fit and properly torqued because of the bed liner so don't be surprised if it's not as easy as your last truck. view full answer...
The design of the Hollywood Racks SR2 2-Bike Carrier - Spare Tire Mount # HRSR2 doesn't allow for you to haul your bikes vertically. The straps that hold the frame of the bike aren't going to clamp tight enough for the bikes to stay in position and they will most likely slide down and make contact with the ground as you drive.
To haul your bikes vertically you would instead need a vertical hanging rack like the Yakima HangOver Bike Rack for 4 Mountain Bikes - 2" Hitches - Tilting # Y02484.... view full answer...
Yes! You can use the Thule EasyFold XT # TH903202 on the front of your 2003 Ford E-350 Van as long as you have a compatible front hitch and enough bumper clearance. If you need a hitch receiver for the front of your van, the Curt Front Hitch - 2" # 33055 will install close enough to the front bumper to accommodate the EasyFold XT without bumper interference. If you already have a hitch installed, I recommend measuring from the center of the hitch pin hole to the outside face of your bumper.... view full answer...
The Redarc Tow-Pro Liberty Brake Controller part # RED24FR can be easily installed on a 2012 Ford E-350 using the Redarc Plug-and-Play Wiring Harness part # 331-TPH-005. If you don't have power to the controller once plugged-in just make sure to check the owner's manual for the fuse locations and then appropriate fuses within the fuse box. view full answer...
While I do not have any way to look up your 1991 Ford Van/Chassis Cab with the VIN information I do see both the Curt # 33055 and Draw-Tite # 65001 front receivers will fit both the standard van chassis and the cutaway chassis. Unless your front end bumper area has been modified you should not have any issues with the fitment. view full answer...
The Roadmaster Front Anti-Sway Bar part # RM-1139-100 that you referenced is confirmed to fit your 1989 Ford Camper Van and would minimize sway and driver fatigue by improving the stability and driveability of your vehicle.
You might also check to make sure you shocks are in good condition and that your wheels have good alignment. view full answer...
We do have seat covers for your 2003 Ford E-250 but none for your 1998 Ford E-350. You can try using a universal cover like the Aries Automotive Seat Defender Bucket Seat and Headrest Protector # AA3142G on the 1998 though.
For your 2003 you can use the universal option I mentioned above or you can use one of our custom fit options which comes in the following colors:
Beige - # AL-EAFOA7350TTT
Black - # AL-EAFOA7350BK
Light Gray - # AL-EAFOA7350LLL
Gray - # AL-EAFOA7350GGG view full answer...
For your 2011 Ford Van E-350 we have replacement rear bumpers like the part # 20107 but the # 61000 does not fit your vehicle. The correct fit would not interfere with a hitch that is installed. view full answer...
I reached out to my contact at ComeUp and he said for your 12K Badland winch you want to go with the ComeUp Snatch Block # CU881082 as it has a weight rating appropriate for your winch. The part # CU881079 you referenced would likely accommodate the cable size but it is rated for smaller winches which is why you need the part # CU881082 instead. view full answer...
We do have some Westin bumpers that will fit a 2003 Ford E-350 but I'm not sure how well they will fit with the utility truck configuration (see attached photo of inside of bumper. Also they do have a different design than the one you have in your picture. The Fey Diamondstep bumper comes in 3 different colors:
Silver Powder Coated Steel # 20105
Black Powder Coated Steel # 20107
Chrome Plated Steel # 21105
Please note that these do fall under the Prop 65 warning for California residents. view full answer...
For your 2007 Ford Van E-450 with a factory 7 pole, you need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury Item # 3035-P for the Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional Item # 90195. The factory plug should be located under the dash somewhere around the steering column. view full answer...
For your application I recommend checking out the WeatherTech Semi-Custom All-Weather Front Floor Mats which come in Tan # WTW51TN, Gray # WTW51GR, and Black # WTW51.
The reason I don't recommend using the full-blown custom mats is because motorhome designs will vary so the custom fit options are perfect fits for the E-450 van models but won't always fit perfect with motorhomes. The semi-custom mats will fit a little better for this application.
Attached is a review video for you to check out. view full answer...
For the Camco Olympian Wave 6 Catalytic Safety Heater # CAM57341, a low-pressure regulator is designated as 11" w.c. (water column), as you can see in the accompanying cut outs I added.
You can go from a hose to the furnace with the Camco Low-Pressure LP Gas Regulator with 6' Long Hose # CAM57703, which has the Type 1 male fitting to connect to the heater and a 3/8 Inch - Female Flare fitting on the other end of the hose, though I'm not sure which connection your pipe has so if you need... view full answer...
Possibly.
The Curt # 14053 Class IV hitch could fit, but it would depend on the vertical height difference between the underside of the van's frame and the lowest portion of the back bumper, which is also known as the drop.
You'll need to measure downward from the underside of the van's frame until you clear the bumper. If this distance is less than 2 inches, the Curt # 14053 would fit.
If the drop distance is 2 inches or greater, you'll need to go with a weld-on hitch like the Draw-Tite... view full answer...
We do have an option with the Timbren Axle-Less system to replace your Lippert 5,000 lb axle, and going with this system is a smart choice because they offer you an improved ride compared to a traditional through-axle.
The reason for that is because the Timbrens work independently and have progressive springs that absorb shock better than a traditional axle. I do recommend getting a system with lift to improve the overall ride height, and I'll also add the hub and drum you need with this... view full answer...
I recommend the Draw-Tite Max Frame, part # 75703 for your 1997 Ford Club Wagon. I called my contact at Draw-Tite and they confirmed the # 75703 as a fit.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include... view full answer...
For your 1997 Ford Econoline E-250 van I recommend the Draw-Tite Ultra Frame Trailer Hitch Receiver # 41906 as it is custom fit for your van.
The receiver 37069 was discontinued does not list your van as a confirmed fit.
You will need the T-One Vehicle Wiring Harness # 118344 to give your van a 4-way flat trailer connector. If you are towing larger trailers that require a 7-way the Universal Installation Kit # ETBC7 will connect to the 4-way and give you the wiring required to install... view full answer...
If your 2008 Pleasure-Way Excel is built on the Ford E-350 van chassis then for a rear anti-sway bar you can use # RM-1139-117. If it is built on the E-450 van chassis use # RM-1139-147. For the front you can use # RM-1139-115 which will fit E-250 through E-450 chassis.
I have included a link to our help article on heavy duty vehicle stability for you. view full answer...
I spoke with my contact at Covercraft about your Class C motorhome on the Ford E-450 chassis. They were unsure whether the Covercraft Premier Custom Auto Floor Mats, part # CC76335123 were a fit for your motorhome. These floor mats are designed to fit Ford vans from 2012 to 2014, so if your motorhome has a cab like the Ford vans these may work for you.
If your cab is not the same as the van, then we do not have a floor mat that will work for you.
They also told me that these have a... view full answer...
Go To Results