The Blue Ox # BXW1500 is a weight distribution hitch rated for up to 1,500 pounds tongue weight and 15,000 pounds of trailer weight and includes sway control and the ability to back up while the weight distribution is engaged.
This hitch fits a 2" receiver. If you have a 2-1/2 inch receiver you will additionally need the Buyers Products # 337RTA252 Receiver Tube Adapter.
If you do not already have one add the Curt # A-90 two inch hitch ball with 1-1/4" diameter shank to your order. When... view full answer...
Yes, the Redarc Smart Start Battery Isolator # 331-SBI212D will allow you to have both batteries charging when connected to shore power. You'd need to put this inline with the charge that is currently going to the one battery so that you can run a charge wire to both batteries from it. view full answer...
Since you changed out the motor on your MaxxAir MaxxFan and neither the old nor new motor are working I recommend using a circuit tester like # PTW2993 to verify that the motor is getting power.
If you find that the motor is getting power then it is likely that the operator mechanism is broken not allowing the lid to open and keeping the motor from turning on.
Let me know if the motor has power, and also send me the model number of your fan and I would be happy to recommend the correct... view full answer...
The Brophy Bumper Spare Carrier part # BR56VR is approved for use at the rear of a motorhome like you have and as long as the wheel is less than 17-1/2 inches in diameter it would work well in that regard as well. view full answer...
The Tekonsha Prodigy P3 Brake Controller, # 90195 and # 3034-P, will be all that you need to bypass you factory controller. This brake controller will hook up to your 2016 Ford F350 CC and bypass the factory controller.
The Ford factory brake controller that is in the dash does not have to be removed. You will need to unplug the connector under the dash and plug in the # 3034-P adapter for the Prodigy P3 brake controller to the factory brake controller plug behind the dash.
The vehicle... view full answer...
Since a 34 inch wide frame is a standard frame dimension for a cab and chassis truck you could pretty easily make a hitch designed for a cab and chassis truck like the Curt Class V part # C15445 fit.
You'd have to drill holes in the frame for the hardware to attach but the flanges would be the correct width. view full answer...
Check out the attached link for the instructions with operating instructions for your Demco Hydraulic Brake Actuator part # DM8758521. view full answer...
There isn't an install/rail kit for the B and W Turnoverball hitches that fits your 2023 Ford F-350 so there wouldn't be a way that we can recommend you install the B and W Hitch Center Section part # BWGNRC920 that you mentioned. The only way you could use this would be if you would be willing to fabricate a rail kit of some kind. Which if you were open to that the better option would be the part # BWGNRK1500 which was designed for this type of install. view full answer...
The Lippert frame does not necessarily indicate you have Lippert axles, but since you have the capacity and other measurements it isn't a concern. The manufacturer information for your axles would be found on your axle tag. With 2-1/4" shackles you need the MORryde Suspension Upgrade Kit # MR46ZR.
For a MORryde upgraded equalizer you need the MORryde Rubber Equalizers # MR87ZR. These are designed to work with trailers that have a 33" wheelbase which matches your measurement. They also... view full answer...
The Reese powered landing gear set part # RP500708 will work great for you. It's a dual motor landing gear setup that uses the same mounting bracket dimensions as the Stromberg setup you have now. view full answer...
34 inch wide trailer frame indicates you have a cab and chassis F-350, which we do have solutions for that. But if you have an RV built on a F-350 frame then we don't have a fit that I can guarantee will fit since the rears of those are quite a bit different in dimensions than most vehicles and vary from motorhome to motorhome.
The # 41947 will fit a 2017 F-350 Cab and Chassis and it is a Class IV hitch though. If your Ford isn't a motorhome this would be a great option.
The other option... view full answer...
For your 2023 Ford Edge Titanium I recommend the Curt Trailer Hitch Receiver # C13234. This Class III hitch with a 2" receiver. It has a max gross trailer weight of 4,000 lbs and tongue weight of 600 lbs. It features a bolt-on installation and comes with a lifetime warranty.
For wiring, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C73FR is confirmed to fit your Titanium. The T-connector plugs into existing wiring so no cutting or splicing is required.... view full answer...
We have the Curt hitch extender that fits 2-1/2 inch hitches part # C45048 and can be trimmed down from 34 inches to 24 inches.
At 34 inches it has a capacity of 6,000 lb trailer weight and at 24 inches 8,000 lbs trailer weight. view full answer...
The best sewer hose system to store inside a rear bumper is the RhinoEXTREME RV Sewer Hoses w Swivel Fittings part # CAM39867. This system comes with caps to keep the odor contained so when you are done you can compress the hose, cap it off, and slide it into the bumper. That said, you need to store the adapter fittings separately as they won't fit inside the bumper but that is going to be the case for all of these 90 adapters. view full answer...
Its not in our fitguide but the correct brake controller adapter to use a Tekonsha brake controller in a Ford F-53 chassis is the part # 3034-P.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. view full answer...
The Draw-Tite # 65053 is a fit for the 2016 E450. I've confirmed this with Draw-Tite.
I attached an install picture of this hitch installed on a similar E-450 as yours for you to check out as well. view full answer...
If your 2017 Ford F-350 cab and chassis has all of the 7-way wires ran to the rear of the vehicle but no actual connector what you would need is the part # HM40975-11998. This is a 7 and 4-way that can be wired easily to the wires you have.
I attached an install video for you to check out as well. view full answer...
You can't go wrong with the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 16,000 lbs GTW, 1,600 lbs TW part # EQ64FR It offers the best user experience and is among the best at eliminating sway as you head down the road.
You will need the 2-5/16" Hitch Ball part # C40008 and the Thin Walled Socket for Equal-i-zer Hitches part # EQ70-00-4800 to install the ball.
These three components are all you need to get the set up installed view full answer...
To reach the connector, first locate the notch in the access panel in the center of the dash, near the passenger side. Using a trim panel puller, carefully pry the panel out and undo the locking tabs to remove the panel. You will find the mating connector behind this portion of your dashboard.
See picture for more info. For a trim panel tool we have the part # ALL648544. A small slot screwdriver will work too.
If you fast forward to the 4:45 mark of the attached linked video you can see... view full answer...