The Firestone kit part # F2355 is designed to fit newer Nissan Titans but would not fit your 2017 Ford F-250. Your best option though would be to sell the kit you have on eBay or list in on a Nissan forum as you'll most likely be able to get most of your money back out of it and then will be able to buy the part # F2600 which is a fit for your new truck and the cost will be offset the most.
The replacement brackets for Firestone bags will add up quick and it will make more sense to go... view full answer...
We do have the Bulldog 2-Speed Jack # BD183401 without a spring return. This is a 10,000lb lift capacity 2-speed jack similar to the etrailer # TJD2SP-12000SP-F jack you found. The Bulldog requires a separate Handle # BD701466 as one is not included. We currently do not have drill adapters for these larger jacks as they require more power than a drill can provide under load. view full answer...
The linked page will display all weight distribution/sway control (WD/SC) systems for 2-1/2-inch hitches. None of these 2-1/2-inch systems comes from Equal-I-zer but we do have 2-1/2-inch shanks that can be purchased separately. Part # EQ90-02-4800 works for tongue weight (TW) up to 1600-lbs and provides up to 4-inches of drop or 8-inches of rise. Part # EQ90-02-4900 also is rated for up to 1600-lbs but allows height adjustment from 6-inches of drop to 10-inches of rise.
The key to choosing... view full answer...
Yes, we do carry the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2, part # Y79QR. These are the BaseClip 200 that will fit your 2001 Ford F-250 Super Duty. I have included a product description link below. view full answer...
Part # BWGNRK1116 is the Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitch # BWRVK3400-5W to install it in your 2017 Ford F-250 Super Duty 4WD - 6-3/4 Foot Bed without the factory rail kit. This same install kit also fits the long bed version without the factory rail kit. view full answer...
We only have one 11 foot long awning with the Solera XL 12 volt power RV awning part # LCV000334909-362243. The 12 volt awnings like this one are designed to be powered by the RV's batteries. We do not have any 18 volt setups in this size. view full answer...
The difference between a 2-point and 4-point sway control system has to do with the amount of locations where friction is used on the system to limit and stop trailer sway. A 4-point system like the Equal-i-zer # EQ37120ET you referenced uses friction at the ends of each spring bar on the trailer frame as well as where they mount in the head. A 2-point system will generally just have friction spots at the ends of the spring bars.
A 4-point system will technically provide a bit more sway... view full answer...
Trailer hitch fits for the 2004 Ford F-150 and the 2017 Ford F-250 are not the same. Hitch fits confirmed for each vehicle are shown on the two linked pages. We have 2-inch hitches rated for 10,000-lbs for the F-150 but only 2-1/2-inch hitches of higher capacity for the F-250.
Among the fits for the F-250 is the TorkLift SuperHitch Magnum Trailer Hitch # TLF1008-30. This is a dual receiver hitch that features both a 2-1/2-inch and a 2-inch receiver on one hitch. The top 2-1/2-inch receiver... view full answer...
For back up cameras that use the factory wiring in your 2021 Ford F-250 we have the Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 if you have the 8" monitor in your F-250 or the Custom Third Brake Light Camera for 4.2" Factory Monitor # 3460002 if you have the 4.2" monitor in your F-250.
These are third brake light mounted back up cameras, designed more so for viewing your truck bed, which comes in handy when trying to hook up a 5th wheel or gooseneck trailer. We do... view full answer...
All of our third brake light cameras for your 2014 F-250 can be found under truck cameras on the custom fit page for your truck. I have also added that link below. If you have a factory monitor you need one of the following based on the monitor size:
-Custom Third Brake Light Camera for 4.2" Factory Monitor - Night Vision # 3460025
-Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision # 3460006
If you do not have the factory monitor you could use the # 3460008 which... view full answer...
We have one weight distribution shank that will fit the 3" receiver on your 2022 Ford F-250. That is the Gen-Y Torsion Weight Distribution Shank # GY92RR. This has a maximum rise/drop of 7" and a gross towing weight of 21,000 lbs.
The holes are spaced 1-1/4" apart on center which is standard for most shanks. I recommend comparing this to what you have now just to be sure. The shank requires 1,600-2,400 lbs of tongue weight for the shock absorption feature to function as intended. You... view full answer...
If you click on the hyperlinked part number for the Westin E-Series Round Nerf Bars # 23-1335 it will take you to the product page where you can add it to the cart for your 2003 Ford F-250 with the crew Cab. These will be installed by attaching the mounting brackets to the rocker panel.
There is a wide selection of nerf bars that fit your vehicle which is why I'm guessing you had issues finding it. view full answer...
Yes you do need an install harness to install the Curt Venturer Next part # C74VV in your 2007 Ford F-250 with the part # C51372 being the correct harness. view full answer...
I am sorry to say that we do not carry the replacement air bag 84585 that you are looking for. Since this is an older kit, they could be hard to find. You may be able to get one direct from air lift. Otherwise the only solution we can offer would be to completely replace your air bag kit with a new one like the Air Lift LoadLifter 5000 Ultimate # AL88390, which will be a no drill install on your 2003 Ford F-250. view full answer...
We have several 3-inch lunette ring (pintle eye) couplers that are shown on the linked page. These are offered with and without a channel mount, such as # T1812800 and # T1613700, respectively.
I went to our warehouse and measured the hole size and spacing on part # T1613700. Each hole is indeed 5/8-inch diameter and their centers are spaced apart by 2-inches. view full answer...
Congrats on the new truck, we have two options for your 2021 Ford F-250 Super Duty with the 7.3 gas, the Draw Tite, # 65076 and the Curt, # C31078. Each option having equal specs of 9K line pull and a vertical load of 500 lbs. with a receiver opening of 2"x2" using a 5/8" pin. The primary difference is that the Curt, my preferred option, sets closer to the air dam while the Draw-Tite will set out from the front a little further and the Curt is made in the USA. Each being a fully welded... view full answer...
For your 10000lb Dexter oil bath axle made in 2020 you will need to go with the Kodiak Disc Brake Kit # K2R1058D11E since your axle uses leaf springs, and is not a torsion axle. This will work with dual 16" wheels so you will need to make sure that is what your trailer currently uses.
You will need to use Dexter Axle Oil Hub # 008-430-03 for each spindle to allow you to install the above kit unless you already have idler hubs.
For an actuator to control these new disc brakes I recommend... view full answer...
For a slider hitch confirmed to fit the factory rail kit of your 2017 Ford F-250 short bed we have a few optoins. My favorite is the Demco Hijacker AutoSlider part # DM8550024 as it will automatically slide as you make tight turns. This allows you to not have to remember to have to slide it back or forward ever. Which is especially nice in inclement weather.
The other very popular option we have is the B and W Companion slider part # BWRVK3370. It's not an auto slider but the B and W Hitches... view full answer...
I do have a solution for you to protect the 18K Autosliding Hitch like part # DM8550034 from Demco but unfortunately there are no covers that will fit over the entire hitch, just the part # DM14844 that fits over the head unit.
We have a wide variety of tonneau covers that you can install on your pickup to help protect your Hijacker from the elements. If your pickup is the 2018 Ford F-250 then I recommend going with the BAK Revolver X2 # BAK39330 or the RetraxONE MX # RT60383. Both are... view full answer...
I suggest the Rampage Wireless Backup Camera for Smartphone or Tablet, # RA7710. This portable camera sends images to your iOS device for easier backing up and the magnetic base allows for simple setup and repositioning to suit your needs.
Your RV, like many manufactured in today's market, is built being prewired for a particular brand, the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision, # FOS43TAS and its various packing options. Prewired units only work with the brand... view full answer...
Go To Results