We've checked with Power Gear in the past with your slide out motor number 521066W and found that the correct replacement is the part # LC386327. This would have same performance capabilities as what you have now. view full answer...
The correct front SumoSpring kit for your 2005 Fleetwood Southwind 32VS is the SumoSpring kit part # SSF-171-40-2. And then for the rear you'd want the # SSR-187-54-1 and you'd be set. view full answer...
Tires wearing out on the insides of a trailer typically means the axles are over loaded which is causing the axle to basically bend out. It is odd your trailer essentially has an axle capacity of 7,000 lbs but they have the GVWR listed as 7,700 lbs. This is most likely related to the tongue/pin weight of the trailer not being supported by the axles.
I would recommend a Load Range D in your tire size of ST205/75-14 like with the part # 274-000012 as a Load Range C would basically match... view full answer...
The total width of the # SP501L ladder is 12-3/4 inches. This is the outside measurement of the step pads since that's the widest point. The actual dimension of the step that's usable for your foot to land is about 10 inches between the uprights. view full answer...
There unfortunately is not a database that tells us which specific parts like Leveling systems were used on your 2003 Fleetwood Southwind 37U, but if you can find some identifying information on your landing gear that would allow us to confirm the Replacement Spring Kit for Power Gear Jack # LC359434 will work for you. This particular spring fits on Power Gear Jacks model numbers 359161, 359170, 359364, 359375, 359377, 359384, 359394, and 407120.
I'll also note that if your spring is 16-3/4"... view full answer...
The only canopy screens we offer are the Solera Screen Rooms which are specific to Solera Awnings. For example, if you have a 16' Solera RV Awning then you can use the Solera Screen Room for 16' RV Awning part # LC362219. If you can let me know what awning you have and the length I would be glad to see if we have a screen room for you. I have attached a list of our selection below. view full answer...
All of the relevant dimensions and capacities are the same between the Pro Series Wheel Caster # PS1400750340 and the # JC-102 that you referenced. They basically would fit the same applications as they are both 1,200 lb capacity wheel casters with a 6 inch diameter that fit 2 inch trailer jack inner tubes. view full answer...
I do have some exterior range hood vent options for you but you'll need to determine which is correct for your application based on the shape/size/color etc. as we have no way to look this up for you. Furthermore, you'll need to replace the entire assembly not just the flap portion. The Ventline Exterior Wall Vent for RV Range Hood part # V2111-13 for example is for 10-1/2" wide x 3-3/4" tall rough openings.
I have attached a few other options below. view full answer...
Based on the dimensions and picture of your current AC shroud plus the fact it was designed for a Coleman Mach the MaxxAir Shroud part # MA00-325001 would be exactly what you need. view full answer...
We probabaly have what you need since most RV taillights use the same styled, but I'd have to see a picture of what you have to know for sure. view full answer...
You are correct, the Adco Olefin HD RV Cover for Class A Motorhomes up to 37' Long # AD74ZR that you mentioned is the correct cover for your 2016 Fleetwood Bounder 35K.
Additionally, the RV cover # AD74ZR is the exact same as Adco's 36826, there is no difference. # AD74ZR is just our part number for 36826. view full answer...
Here are the dimensions for the Roadmaster Adapter Kit for Blue Ox Motorhome Mounted Tow Bars, part # RO64FR.
pin size = 3/4"
pin length = 5"
measurement from inside lip to the end of the pin = 4" view full answer...
Since you can get the motor to work, and the steps are not opening/closing properly then it does sounds like the control module could be the issue.
We do carry the correct replacement control module for your 909506000 Kwikee control module.
- Replacement Control Unit for Kwikee Electric RV Steps # LC379606 view full answer...
To replace the lights in your 2014 Fleetwood Southwind Motorhome you'll need to first remove one of your current lights and measure the cutout hole. This will allow you to pick a similar fitting light so that you don't have to enlarge the hole or worry about the light being smaller than the hole.
For example, the Glantastic LED RV Puck Light # 328-K-58L34P9 you were looking at requires a 3-1/4" diameter cutout hole. If you can tell me what your cutout hole size is then I can help find... view full answer...
The MaxxAir Mini Deluxe Trailer Roof Vent # MA00-03801 fits a 14 inch square opening. You can measure or at least get a very close estimate on your existing vents to determine if they too fit a 14 inch square opening. If so then you can indeed use # MA00-03801. view full answer...
I can certainly point you in the right direction. If both Ac units are original to your camper, it is safe to assume that they are both identical. To replace your Coleman Mach Air conditioners I recommend the Furrion Chill HE # FR82PV. This is a 13,500 BTU air conditioner. This one includes a conversion kit which will make it compatible with your existing Coleman systems. So you will not have to change out anything inside the camper. This will be a nice upgrade from an older Coleman unit.... view full answer...
If the motor you found on your 2002 Fleetwood Southwind 35r has the number 386480 like I believe is what you said then yes, the part # LC386480 is the correct replacement. If you are not sure what you have you'd have to check and see what yours says since we don't have a way to look up what you may have just based on the motorhome info. view full answer...
In order to find the correct replacement rear clearance lights for a 2008 Fleetwood Southwind you'll need to take some measurements, note the shape and color then choose from our selection which I have attached for you below. I don't have a way to look this up for you. The lights appear to be oval so something like the LED Clearance or Side Marker Trailer Light part # MCL0030RBB may work. view full answer...
Both the Front # TFFF53B and Rear # TFRF53A Timbren Suspension Enhancement Systems for your 2007 Fleetwood Southwind RV Motorhome will not require drilling into the frame of your Ford F-53 chassis. They both bolt in place of the factory bump stops for the leaf springs by using their same mounting points. view full answer...