The 12 volt accessory circuit of your 7-way can put a maintenance charge on your deep cycle battery. Not enough to significantly charge it but it would keep a fully charged battery topped off. For a more significant charging option the Redarc BCDC part # RED96FR is more optimized for charging and would be your best option. view full answer...
For your 2005 Fleetwood Bounder 34F, I recommend replacing the rear sway bar first. The rear needs more stability than the front based on the axle placement and weight so it will make the greater impact. I recommend the Roadmaster Rear Anti-Sway Bar # 1139-144. This retains the factory sway bar. The factory u-bolt may not be long enough for the factory nut, washer and 1/2" plate. If not, square top u-bolts will need # RM-590050-00, and round top u-bolts will need # RM-590050-10.
To... view full answer...
We don't carry just a lens replacement for the Glo Brite 446 but we have the very similar Optronics LED light replacement part # MCL44RB1 for a red replacement that would work well! It's an LED and priced great too so it would be an easy solution. view full answer...
For your 2020 Fleetwood Bounder we have the SumoSprings kit part # SSR-187-54-1 which is a fit and would work great.
I attached an install video for this kit on a similar 2019 Bounder for you to check out. view full answer...
As long as you have good enough access to the jack legs you can leave them installed on your trailer when swapping the springs part # LC359434. I'd recommend putting something under the foot when the spring is off.
The top bolt that Conner referred to is the one at the top of the spring and not at the top of the jack. view full answer...
If you didn't want to replace the entire fixture, you could swap out the halogen bulbs inside the 12V RV Puck Light part # 277-000125 for LEDs with the G4/JC10 LED Light Bulb part # DI93VR. If you did want to replace the entire fixture, the closest option we have is likely the Gustafson 12V RV LED Puck Light part # 277-000343. view full answer...
The biggest improvement you can make to your 2014 Fleetwood Bounder in terms of ride quality, stability, and sway reduction would be with a rear sway bar upgrade part # RM-1139-149. The next biggest improvement comes with a front sway bar with part # RM-1139-148 which is a confirmed fit as well. With both of these installed you'd have a drastically better driving experience that won't have the issues you mentioned when getting passed by semi trucks. view full answer...
The correct Roadmaster Reflex steering stabilizer you need for your 2019 Fleetwood Bounder with a 24k GVWR is the part # RM-RBK25-RSSA actually. We verified this fit with Roadmaster! view full answer...
The Phoenix Faucets 4" Dual Handle # PF213264 that you referenced would be a great replacement faucet assembly for your 2001 Fleetwood Bounder as it is a standard style of faucet and diverter like what your RV has.
Instructions are included, but I attached a link to the instructions down below for you to check out as well. view full answer...
The Solera 12V Electric RV Awning Conversion Kit part # LC434724 for white or part # LC434723 for black is what you need to convert your awning from manual to electric. This is a complete, all inclusive kit that comes with everything you need to make the swap. It will replace your existing arms and reuse your old roll tube and fabric. It comes with a switch you will mount and wire to your battery for operation.
Please note, the Solera 12V Electric RV Awning Conversion Kit only works with... view full answer...
For your 2013 Chevy Equinox, I recommend the Blue Ox Alpha Tow Bar # BX7380. This will handle the weight capacity and will work with Blue Ox Baseplate # BX1689. Because your Bounder trailer hitch is too high, you will need to use a high low adapter. I've attached the link to all your options and also attached an article for you to determine the proper fit.
Let me know if you have further questions. view full answer...
Without knowing what brand ladder you have it's hard to say, but we do have the # SPN-416 for if you have a Surco ladder.
Or if you have a Stromberg Ladder you'd want # 8531-B. view full answer...
From the specs available to me it appears the 2018 Fleetwood Bounder Motorhome is constructed on the Ford F-Series (F-53) chassis with a V-10 engine. Please verify this within your owners manual for your specific vehicle/motorhome and identify if you have the either the 22,000 GVWR or the 24,000 GVWR chassis.
For your 2018 Fleetwood Bounder Motorhome there are three primary upgrades that I recommend toward suspension enhancements. I suggest the Roadmaster Reflex Steering Stabilizer... view full answer...
I attached a chart that shows how to determine the correct torque for the lug nuts of your Fleetwood. You'll need to know the diameter of your wheels, the diameter of the studs, and the type of metal the wheel is made of. view full answer...
Your concern about the stability and drivability of your 2001 Fleetwood Bounder motorhome is definitely understandable, as these rigs can be a chore to handle at times even when not towing a dinghy so I definitely recommend adding parts to help reduce the sway and stabilize your motorhome, and changing your shocks certainly won't hurt either.
The best way to enhance and stabilize the drive of your 2001 Fleetwood Bounder is to add an aftermarket rear anti-sway bar because they are better... view full answer...
For your 2017 Fleetwood Bounder 35K we have the Air Lift kit part # AL57344 as a confirmed fit for the rear axle and part # AL88240 for the front.
Then for a compressor kit the Air Lift WirelessAIR Compressor part # AL58WQ would work great as it can independently control the front and rear bag pressure and uses your phone to control everything. view full answer...
Thank you for reaching out and for the photos!
We try to carry over the wiring brackets and for a long time they didn't change which is why we carried it over. With this new information we will definitely be updating our website.
For your application I recommend using the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness # RED52VR which you will install by cutting off your current connector and splicing this to the wiring function for function with butt connectors #... view full answer...
We have just what you need to improve the handling of your 2006 Fleetwood Bounder W22 chassis with the rear sway bar part # RM-1259-109. For Class A motorhomes like yours the biggest ride quality improvement you can make is with a rear sway bar. This will be a night and day difference.
Next biggest improvement you'll make is with a front sway bar which the part # RM-1259-106 is the correct kit which also includes a TruTrac rod kit as well. Finally the next biggest improvement you'll make... view full answer...