Yes, the black wire on the Curt T-Connector Vehicle Wiring Harness part # C55562 which is a fit for a 2005 Dodge Magnum will need to be run to the vehicle's positive battery post with a fuse in between. The extra wire, fuse, fuse holder, and wire connectors that you will need for this are all included with the kit for you. view full answer...
When we installed the Curt Hitch part # 13465 on a 2005 Dodge Magnum the top of the hitch opening ended up being 10 inches from the ground. To determine what ball mount you would need to tow your trailer level you will want to take your trailer on level ground, with the trailer sitting as level as possible and measure the distance from the bottom of the coupler to the ground.
How many inches that is above or below 10 inches is the amount of rise/drop you need. So if you measure 14 inches... view full answer...
It sounds to me like you may have a ground problem. There are several places to look for a poor ground connection. I recommend starting with the trailer connector on the vehicle. You will want to check to make sure it is securely grounded to a clean metal surface on the vehicle frame or chassis.
Next, I would take a look at the connector on the trailer. Check to make sure that it is free of dirt and corrosion and that the ground wire is securely grounded to a clean metal surface on the... view full answer...
The wiring harnesses for your 2006 Dodge Magnum, the Vehicle Wiring Harness # C55562 won't have a specific side of your vehicle to install on; it utilizes the taillight assemblies to install. view full answer...
Yes, the SportRack Semi-Custom Roof Rack for Naked Roofs # SR1002 that you referenced is confirmed to fit your 2005 Dodge Magnum with a naked roof and sunroof.
I confirmed this with Sportrack. view full answer...
The Curt Trailer Hitch Receiver # 13465 that you referenced is the confirmed to fit your 2005 Dodge Magnum.
For trailer wiring you would want the part # C55562.
For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. view full answer...
The reason you want to run the power wire all the way up to battery is so that you bypass all of the delicate wiring of your vehicle. The power wire is required on trailer wiring harnesses for some vehicles because the electrical system on those vehicles cannot handle the amperage draw associated with trailer lights. Powering the converter box with a power source that doesn't come from the battery would defeat the purpose.
I attached an FAQ article on routing the power wire for you to... view full answer...
According to the owner's manual for your 2006 Dodge Magnum, tire chains can only be installed on the rear two wheels of the vehicle and must be Class S complaint. With this in mind, I recommend using the Titan Chain Alloy Snow Tire Chains part # TC1553 for 215/65-17 tires or part # TC1555 for 225/60-18 tires.
The Titan Chain Alloy Snow Tire Chains are Class S compliant and have a diamond chain pattern that will increase traction and stopping power when driving forward and during turns.... view full answer...
It sounds like the trailer hitch for your 2007 Dodge Magnum is pretty recessed behind the rear bumper. If you are having trouble using a hitch-mounted accessory like a bike rack or cargo carrier without it interfering with the bumper, a good solution is a hitch extender like the Brophy # HE06. This particular unit will insert into a 2 inch hitch receiver and provide you with a 7-3/8 inch extension. I have attached a link that will take you to our complete selection of hitch extensions that... view full answer...
If your vehicle has the 7 way flat connector then item #37345 will work for your vehicle. If you have the 7 way round connector you will need part # 30709. I have provided links to both below and a link to our wiring adapter fit guide for your convenience. view full answer...
The trailer hitches we offer for your 2005 Dodge Magnum, like part # 36548, are rated with a 3500 lb weight capacity. We currently do not offer any that would fit your vehicle with a higher capacity.
I recommend you check your owner's manual or with your dealership to verify the maximum towing capacity. From what I was able to find with some research on your vehicle I found that it is rated with a maximum towing capacity of 2,000 lbs. You will not want to exceed the towing capacity of... view full answer...
Curt offers two different receiver hitches for your 2005 Magnum, the Class II you mentioned, part # 12240 or a Class III, part # 13465.
Although both receivers would work great on your vehicle, I always recommend choosing a Class III with a 2 inch receiver opening over the Class II with the 1-1/4 inch opening whenever the option is available. The more common Class III 2 inch receiver will provide a better selection of hitch mounted accessories like bike racks or cargo carriers.
If you... view full answer...
Although taillight converters, just like any other electronic device have a set lifespan, losing two of them in rapid succession tells us that something is going on.
The two most likely causes are a short circuit in the trailer wiring and overloading the converter.
First, check the wiring on your trailer. Beginning at the trailer connector and working your way back to each lamp, closely examine the wiring. Wire insulation can become brittle over time, look for any cracked or worn wire... view full answer...
Yes, I have recommend load extenders such as # EM07600 for cars, trucks, vans, and SUVs. Sometimes it is just the right tool for the job! Once installed in the hitch the minimum height is 16 inches. If you measure from the top of the receiver opening up 16 inches on your 2006 Dodge Magnum that will be the approximate height of the extender once installed. I have linked a video review of this extender for you.
In order to use this extender your Magnum would have to have a Class III trailer... view full answer...
Yes, I checked with SportRack and they confirmed that the SportRack Roof Rack part # SR1002 that you referenced would fit your 2006 Dodge Magnum with a naked roof. view full answer...
You will need to start with a 4-way (if you do not have one). For that you would want the # C55562.
From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake... view full answer...
There is a chance that the previous module failed due to the trailer lights drawing too many amps or a possible short somewhere in the trailer's wiring. Before installing a new harness, I recommend inspecting the wiring on your trailer to make sure that there aren't any problems such as exposed wires or corrosion that could cause failure in the harness again.
I recommend replacing the harness on your 2005 Dodge Magnum with the Curt Custom Fit Vehicle Wiring Harness, # C55562. The Curt... view full answer...
Sounds like the wiring on the 2006 Dodge Magnum is working since you have tested it. But, make sure that the main ground for the converter is attached to a bare metal surface. Moving the ground might help as well. Sometimes, when there is very little load on a system with a bad ground, like using a tester, the problem will not show up until there is more power draw. I also recommend trying out the trailer on another vehicle if possible.
After checking that, that leaves the trailer. Most... view full answer...
The Tekonsha Brake Control harness, part # 3020-P, is designed to fit Dodge/Chrysler vehicles equipped with a factory tow package that includes a brake controller port underneath the dash. The Magnums did not get these tow packages. You can still use a brake controller, but you will need to do some wiring since you do not have the brake controller port.
There are 4 wires on most brake controllers: white, black, red and blue. The white is a ground wire and should be run to the negative... view full answer...
If you installed the power line from the converter to the battery you should have power to the trailer lights. The terminal under the hood is fused so it would provide an extra layer of protection, but is not necessary as long as the inline fuse is used. If all the other wiring is connected properly to the connection points behind the taillights. You may have a bad ground somewhere or the fuse may be bad if you did not remove it before installing the power wire.
If you did not install... view full answer...