Since the Stromberg Carlson Trailer Tray Cargo Carrier # CC-255, has tray dimensions of 32" long x 20" wide and measures 14" wide from back to angle cut. And the RC Manufacturing Z-Series Truck or Trailer Underbody Toolbox # UBT1818-30 overall dimensions are 30" long x 18" wide x 18" tall, we just need to make sure that the box will fit on the carrier. The edges on the carrier are angled, because of those angles the box will not fit on the carrier. This determination was based on how far... view full answer...
I checked with Thule for you and they do not have any replacement mounting hardware for a Thule Combibox 250, so we can't confirm a fit for any hardware. That said, mounting hardware can often be made to fit, though it will likely require you to drill new holes in your cargo box.
If you are willing to do that you should be able to use the Replacement Mounting Hardware for Thule Weekender Cargo Box # 1032802. view full answer...
If your 2001 Jayci Kiwi 21C has double-eye springs, you can use the Dexter Trailer Springs Over-Under Conversion Kit to improve your ground clearance. You will gain the width of your axle (either 2 3/8" or 3") plus about 1/4" for the spring seat, as well as the depth of the springs.
From what I found, your 2001 Jayco Kiwi 21C weighs about 3300 lbs. At this weight your trailer should have
2 3/8" axles. For those axles you will need the Dexter Trailer Springs Over-Under Conversion Kit
#... view full answer...
The Trailer Connector Adapter, # PK12716, will plug into an existing 7-way trailer connector on the vehicle. If your 2006 Chevy Suburban has a 7-way connector on the rear of the vehicle you will be able to install this adapter.
If your 2006 Chevy Suburban does not have a 7-way connector installed on the rear of the vehicle, but has the factory socket located above the spare tire you will need to install the Hopkins Replacement Multi-Tow 7-Way and 4-Way Trailer Connector, # 30955. You... view full answer...
Yes, the Curt T-Connector Vehicle Wiring Harness part # C55774 will fit a 2006 Chevrolet Suburban and a 2000 Chevrolet Silverado as long as they both came with a factory 7-way as this connector is designed to replace the factory 7-way. I also recommend using a bit of part # 11755 before mating the two connectors together. If you don't already have a mounting bracket on the hitch than you can add one using part # C57202. view full answer...
Unfortunately I can't help with brackets for that grille guard as it isn't one we carry. All of the Westin Sportsman and similar Aries Grille guards for that model year have 3 holes and the brackets are much different than what you have pictured. When the brackets aren't the same the grille guard often won't fit based on design. It is more likely than not with a second hand grille guard that it is not the correct fit for your vehicle.
If you need a grille guard compatible with your... view full answer...
If you are asking if the Rhino-Rack Round/Square Crossbar Fit Kit # MUBK is compatible with SURCO square crossbars, then the answer is yes.
Using the Rhino-Rack Round/Square Crossbar Fit Kit # MUBK will allow you to use Rhino-Rack steel mesh baskets, steel mesh trays, or alloy trays on square or round crossbars like the SURCO Safari bars. view full answer...
The Swagman # 64400 bike rack should be able to handle your 26 inch cruisers with no problem. Since this rack uses straps to secure the bikes to the rack, and the rack does not use anti-sway cradles that prevent the bikes from swaying back and forth and striking each other or the vehicle carrying them, this is a rack I would typically recommend for an occasional rider who is transporting their bikes short distances. The rack has a 140 lb weight capacity, with a 35 pound per bike limit.
If... view full answer...
The Curt # C14029 is a Class IV hitch with a 10,000 lb capacity like you mentioned; the difference in capacities often comes down to construction, design and attachment points. In regards to the correct hitch and ball mount for your towing capacity and drop, the previously mentioned Curt # C14029 would be a great choice. As for ball mount for different amounts of drop, I recommend the Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 5-1/2" Drop, 6-1/2" Rise Item # AM3411.... view full answer...
The Replacement Head for Husky Weight Distribution Systems part # HT31516 does not come with a hitch ball or sway control ball but you can add them using part # HT39386 for hitch ball and part # C40093 for the sway control ball. We also have replacement spring bars available as part # HT31521. The sway control ball is made by Curt but it will still work with your Husky system.
Please let me know if you need any other parts or have any further questions. view full answer...
Appreciate the photo, and there is a way to add a platform rack to your 2020 Chevy Suburban, but not the LockNLoad; instead, what you'd need is one from Rhino-Rack, which is the following part number:
- Rhino-Rack Pioneer Platform Rack with Backbone Mounting System - 84" Long x 56" Wide # RR68AB
The Pioneer Platform # RR68AB is similar to the LockNLoad, and will also mount to your rails, but does not use towers or feet like a roof rack - its backbone system mounts directly to your Suburban's... view full answer...
As far as ground clearance goes for your 2015 Chevy Suburban you will want to use the Curt Front Mount Trailer Hitch Receiver # C31073 over the Draw-Tite Front Mount Trailer Hitch Receiver # 65064 because the instructions call for you to cut the front fascia whereas the Draw-Tite instructions fort of hint that you may not need to.
The access hole that needs to be cut for the Curt installation if 1-1/2" x 3" so at the most you will have an approximate 1-1/2" of the receiver hanging below... view full answer...
I can't tell you exactly what air pressure you need to put in the bags of the Firestone Coil-Rite kit part # F4186 but I can help you get to the right pressure. Basically you want to put whatever air pressure is needed to allow your truck to sit level after the trailer is hooked up. view full answer...
The key to confirming a good fit of a wind fairing like the Rhino-Rack # RRRF3 on a factory-installed roof rack crossbar is knowing the bar dimensions and the size of fairing you want.
This particular fairing measures 44-inches and its mounting hardware will fit a crossbar up to 1-1/4-inches tall x 3-1/2-inches wide. The bar also needs to provide at least 7/8-inch of room between the vehicle roof and the bottom of the bar; and there needs to be at least 35-1/2-inches of available bar... view full answer...
Yes! The Tekonsha Prodigy P2 # 90885 works with the # ETBC7 on your 1998 Chevy Suburban. However, in order to install the # ETBC7 to prep the vehicle for the brake controller, you need a 4-way wiring harness installed before installing the # ETBC7.
If you need a 4-way wiring harness, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55319. This harness conforms to the combined wiring system on your vehicle. This means that the brake and turn... view full answer...
The Powerbuilt 1-7/8 Inch 12pt Socket # ALL643216 that you referenced will fit in the Equal-I-zer weight distribution hitch, like # EQ37120ET, # EQ37140ET, # EQ37040ET, # EQ37060ET and # EQ37100ET, to torque down the hitch ball.
In the review video on the # ALL643216 socket, we found we were able to torque down the hitch ball in the Equal-I-zer hitch just fine with the socket.
I have attached the review video of this socket for you. view full answer...
Yes! The Rhino-Rack Pioneer # JB0301 is a great rack for carrying ladders, lights, luggage, and load of other stuff!
This is such a fun platform rack, and it is definitely larger than your other Yakima Mega Warrior # Y07080-82 rack even with Yakima's extra 22" attachment. You can customize the Pioneer with different accessories for your different needs. If you're carrying ladders often, I recommend getting some Rhino Rack Load Stops # RRRLH to keep your ladders in place. These just slide... view full answer...
For your 2001 Chevy Suburban the 4WD or the 2WD will not matter for the front hitch. The choice for your vehicle will be if it is the 1500 series or the 2500 series Suburban.
If you have the 2001 Chevy Suburban 1500, the Curt Front Hitch, # 31302 will fit. Since you said your fascia has a square hole cut into the middle of it, the Curt Hitch, # 31302 world work great for you. The installation instructions on the Curt hitch says that it can be installed as a through bumper installation... view full answer...
7- and 4-Pole Trailer Connector Socket # HM40975 will fit in place of the factory connector on your 2008 Chevy Suburban. The wiring that is connected to the back of the existing connector will unplug from it and plug into the back of this new connector.
The connector will likely not fit the same mount as the factory one but it does come with a mounting bracket of its own. Installation on your Suburban will be similar to the Tahoe in the video I have linked for you. view full answer...
If your 1995 Chevrolet Suburban's OEM hitch a has a 2 inch receiver opening, then the Ultra-Fab Dirt Bike Carrier will fit this vehicle.
I researched the 1995 Suburban and found that the tongue weight for this year models where between 700-1000 lbs depending on the rating of the equipment installed. Check your hitch to make sure that it is rated at least up to 500 lbs. There usually is a label attached to the hitch that will give you this information.
Do not overload the stated hitch... view full answer...
Go To Results