The Replacement Front and Rear Flap Seal # PARTS-326A0001, for the BAKFlip Truck Bed Tonneau Covers, measures 65" long, 3/4" wide on the front overlap, 1-1/4" wide when measured underneath, and is under 1/8" thick.
This comes with 2 of the seals, alcohol prep pads, adhesive promoter, and 3M tape. view full answer...
I confirmed with Westin that the weight capacity of the Westin R7 Nerf Bars - 7" Wide - Polished Stainless Steel # 28-71270 is 250 pounds. view full answer...
The Front # TLC2224 and Rear # TL54FR TorkLift tie-downs that fit your 2021 Chevrolet Silverado 1500 have a shipping weight of 62 lbs so you'll be looking at about 57 lbs for the tie-downs. The weight of the turnbuckles can vary but if you were going with something like part # TLS9529-2-LK which is stainless steel then you're looking at another 17-ish lbs which brings you up to about 74 lbs for everything (give or take a few pounds).
Currently (as of October 2021) there are no aluminum... view full answer...
The Erickson Big Bed Load Extender # EM07600-07601 has a total shipping weight, including the carton and packing material, of 57-lbs. So once you account for the few pounds of cardboard in the carton the actual net weight will be right around 53-lbs total for the assembled extender. view full answer...
I checked out pictures of your Grand Design Imagine 2670MK and it appears the Pro Ride Weight Distribution system part # PR97QR would fit pretty easily but there's a couple measurements you can take to know for sure. The U-bolts attach to the trailer frame at 22 inches from the center of the ball coupler back give or take 1/2 inch and the weight distribution jacks install 26 inches back from ball center give or take 1-1/2 inches. We have found that works pretty well with most trailer setups... view full answer...
The throw bolt for the Valterra Deadbolt Lock for RVs # L32CS3008 is 1/2" wide x 3/4" tall x 5/8" long. Typically there's quite a bit of space in the door frame to allow for an additional 1/4" length of this throw bolt versus the one you currently have. view full answer...
The Curt Echo Under-Dash Trailer Brake Controller item # C27JR needs the Curt Custom Wiring Adapter for Trailer Brake Controllers item # C51451 to work with your 2018 Chevy Silverado Z71. That is why it is a confirmed fit on the wiring adapter product page and not the brake controller page. This brake controller will work great and have no issues on forest roads and you will have an easy plug and play installation. view full answer...
When the Quick Link part # C82932 is fully open the opening measures 5/8 of inch so a 5/16 inch diameter chain link would easily pass through it. It's pretty common to see quick links that are noticeably larger than the chains they are used on. view full answer...
Congrats on the new truck and thanks for the picture! I will be happy to answer all of your questions.
The Thule TracRac SR Sliding Truck Bed Ladder Rack item # TH43002XT-782 is only available with the silver uprights and crossbars.
The Truxedo Elevate Item # TX96NV mount in T slots, is confirmed to fit your truck, and they only other sliding ladder rack we have for your 2022 Silverado. It is compatible with BAK, Extang, Retrax, and Truxedo tonneau covers with T slots not Thule. This... view full answer...
The Demco Hijacker AutoSlide part # DM8550041 weighs a total of 332 lbs but since your payload capacity is the weight capacity of the truck's bed and this hitch is supported by the truck frame instead you do not have to factor the weight of the hitch against the payload capacity. view full answer...
The Replacement Header Stop # TX1704187 that you referenced is designed specifically for TruXedo Lo Pro and Edge tonneau covers so there's a good chance it won't fit your cover unless you have either of these models or it's the same size. With that being said I did go out to our warehouse and measured the piece to be 3-5/8 inches long and 1-3/8 inches wide.
If you can tell me what model tonneau you have on your truck I may be able to track down the right replacement part. view full answer...
I went out to the warehouse and pulled brake controller wiring harness # 3016 for the 2015 Chevy Silverado to measure it for you. The overall length is approximately 30-3/4 inches. The length of the wires between the plugs on each end is approximately 28-3/4 inches.
If you wanted to splice in additional wire to the harness you could with 10 gauge wire like part # 10-1-1 sold by the foot, but a longer version of this harness is not available. view full answer...
The Demco Autoslide 5th Wheel Trailer Hitch # DM8550040 is going to weigh 309lbs and the Install Kit # DM8552034-71 is 105lbs. The Reese # RP30047 is going to be a lighter option at 108lbs with Install Kit # RP56015-53 being 103lbs. But do remember the Reese Sidewinder # RP77FR is going to weigh approximately 120lbs more than your standard pin box. So while you loose hitch weight in the truck you are going to have a higher tongue weight. view full answer...
Hitch ball mounts are typically measured from the center of the hitch pin hole to the center of the ball hole. With this measurement you can compare that to your trailer hitch and know where the hitch ball will be located. For example, the Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs, part # BH20, measures 13-1/4" from the center of the hitch pin hole to the center of the ball mount.
I have included a product description link, a video demo link, and... view full answer...
Draw-Tite hitch # 41990-07 has not been rated for or tested with weight distribution and because of that the manufacturer places a "not for use with weight distribution" warning on the hitch. This is common for weld-on truck hitches.
We do have Class IV custom fit hitches for the 2016 Chevy Silverado 1500 that are rated for weight distribution such as Curt hitch # C14006. When used with weight distribution it is rated for 1,200 pounds tongue weight and 12,000 pounds gross trailer weight.... view full answer...