In regards to the Better Bath RV Shower Pan part # LC210375, I have attached a photo below with the distance from the center of the drain hole to each outside flange. view full answer...
The actual outside dimensions of the stake pocket anchors part # T55Z that you referenced where it slides into the stake pocket is the exact dimensions you listed. 3-1/2 inch by 1-1/2 inch. I attached a picture that has these dimensions listed. view full answer...
Yes, if you install the Buyers Products Flatbed Bumper Hitch Plate w/ 2" Receiver # 3371809055 using bolts in the 6 holes would adequately secure the hitch and allow you to tow a trailer up to 17,000 lb. view full answer...
The measurement that you will want to take is the outer diameter of the inner ring and the outer diameter of the inner ring with one of the tabs (see photo). You will also want to count the bolt holes on the wheel and know the wheel diameter.
The Baby Moon Center Cap, # AM90086, will fit 13 inch, 14 inch, or 15 inch 5-lug conventional steel wheels. The outer diameter of the inner ring should be 9 inches and the outer diameter of the inner ring with one of the tabs should be 9-1/4 inches.... view full answer...
I reached out to the manufacturer, Buyers Products, who told me the pre-drilled mounting holes are 1/2" wide x 3/8" tall for their 12 x 18 mud flaps, which are the following part number:
- Truck Mud Flaps - Black Rubber - 12" Wide x 18" Tall # 337B1218LSP
I have added a diagram of the dimensions for you as well. view full answer...
The Aries Round Nerf Bars - 3" Diameter - Polished Stainless Steel # AA204018-2 are rated for a static weight of 500 lbs according to my tech contact at Aries. view full answer...
The Curt Overbed Folding Gooseneck Trailer Hitch part # C6130-52 that you referenced is custom designed to fit 2011 and newer GM trucks. Its not designed to fit certain width frames.
If you are looking for a gooseneck setup for your 1973 Chevy Truck then I would recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit # BWGNRK1400 as this is custom designed for your vehicle.
I attached a link to installation instructions also. view full answer...
We do offer slip-on towing mirror extensions that will work on your 1996 Chevrolet K3500 Pickup. These are shown on the linked page. CIPA offers their slide-on towing mirror set # CM10200 which is custom-fit for the mirrors on your truck. These fit on both the manual and powered OEM mirrors.
The link also displays complete replacement towing mirrors that bolt on in place of the OEM units.
I contacted CIPA for the dimensions you asked about. Mirror # CM55100 has a glass surface that measures... view full answer...
The Curt 2 inch Bumper Hitch, part # E-3S has a 5000 lb towing and 500 lb tongue weight capacity when installed according to the instructions linked below. The Curt Hitch should easily pull your pop-up with no problem whatsoever. view full answer...
We only carry the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter # AM3200 of the two part numbers you referenced which this comes with a 9 inch offset from the center between the rails. The distance between the rails is 22 inches so the ball center would be 7 inches in front of the rear rail. view full answer...
The distance from the base to the bottom of the "V" on the CE Smith V-Wing Bolster Bracket part # CE26244G is 2-1/4". I have attached a photo of this measurement for you as well. view full answer...
For the bed rails compatible with your 1996 K3500 Diesel Dually 4x4, I recommend the Reese Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches - 10 Bolt # RP30035. The instructions on this will put the king pin center approximately 1-1/2 inches forward of the center of your rear axle.
These rails will work with an older Demco Hijacker similar to the # DM6076P-16K. You may also be interested in adding a 2nd 7-way trailer connector to the bed of your truck using the... view full answer...
The outside diameter of the Replacement Acrylic Lens # W802650 that you referenced is 4-1/4 inches and is designed to fit a housing that is 4 inch so dimensionally this would match what you need. view full answer...
The # BWHDRH25122 measures 5 inches from the frame to the top of the hitch receiver. The # BWHDRH25198 measures 7-3/8 inches from the frame to the top of the receiver. view full answer...
The Shackle Links, # 115052, are 3/16 inches thick.
They are also 1-1/4 inches wide; 2-5/8 inches from the center of one hole to the center of the other hole, with a bolt hole diameter of 9/16 inches. view full answer...
With the Timbren kits you still have to abide by the overall capacity of the vehicle. Basically the Timbrens give you more suspension support to allow you to carry the capacity of the truck in the safest way possible but they do not allow you to increase the capacity of the truck.
Based on your truck's year/make/model and the numbers you found on your spring you do have the part # TGMRK10 which can give the truck up to 3,000 lbs of additional suspension support. If you need to replace... view full answer...
If you are absolutely sure you have a good 12 volt source ran to the black wire of the P2 part # 90885 and a good ground ran to the white wire of the controller and you are not getting any activity on the display of the controller it would be bad.
The display should at least light up. If not then the controller has an internal problem that needs to be addressed. view full answer...