Yes the Extendable Hitch Mounted Step for 2 Hitches - Steel - Black - 500 lbs Item # 288-08400 that you referenced would fit the 2 inch hitch of your 2011 Chevy Avalanche. view full answer...
You can either go with a universal mirror like the CIPA # 7070-2, otherwise you will need to look at a replacement mirror set like the K-Source # KS62093-94G for your 2008 Chevrolet Avalanche having the chrome cap mirrors. There are no custom fit mirror extensions like the CIPA # CM10900 that will fit with the chrome caps. view full answer...
I do have some good replacement options for you although you'd have to drill a few new holes for mounting as none will line up with what you have now as the model is discontinued and there are no direct replacements. I recommend the Dexter DX7.5 Drop-N-Go Brake Actuator part # 099-175-20. This coupler is for disc brakes, has a 7,500 lb capacity, designed for a 2" hitch ball, and has an electric lockout actuator. view full answer...
If you were to install the Curt # 31302 Front Mount Hitch so that it is the "through bumper" instead of "under bumper" configuration you will need to cut out a 3 inch square hole that is located 3-1/2 inches below the top edge of the plastic fascia. If you go out and measure 3-1/2 inches below the top edge of the plastic fascia on your 2002 Chevrolet Avalanche you will be able to determine whether that installation method will interfere with your license plate or not.
Front mount hitches... view full answer...
The Tekonsha Plug-In Wiring Adapter, # 3015-P, will not work with your 2007 Chevrolet Avalanche because General Motors quit offering the plug in type connectors on trucks and SUVs with a factory tow package in 2007. Instead, you will find a bundle of blunt cut wires to the left of the steering column under the dash with a white label. The brake controller wires will connect directly to the wires under the dash.
Once you have the the brake controller wired you will need to get under the... view full answer...
AirLift 1000 Air Helper Springs for Coil Springs # AL60769 are unfortunately not compatible with vehicles that have the factory installed auto-leveling option.
However, if you carry/tow heavy loads regularly and experience sag, I recommend a quality yet cost effective bump stop replacement like the Timbren Rear Suspension Enhancement System # TGMRYS4. These are rubber springs that replace the factory bump stop mounted on the underside of your frame at the axle. The Timbren kit fits... view full answer...
I believe you are asking if there is a brake controller that you can just plug into your 2003 Chevy Avalanche that has the factory 7-way, and the answer is yes. For an '03 Avalanche with the factory 7-way, the only thing you will need is the brake controller and plug-in adapter. The controller and adapter I highly recommend for you is from Draw-Tite:
- Brake EVN Trailer Brake Controller # TK63VR
- Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM # 3015-P
I recommend... view full answer...
I checked fits with both Yakima and Thule and there is not a bike rack that attaches directly to the factory cross bars on your FJ Cruiser at this time. You could use the Yakima Roof Rack, parts # Y00409, # Y03536 and # Y33TR to install the FrontLoader bike carrier on the roof of your vehicle. view full answer...
It does appear to have proper fit for the Timbren Rear Suspension Enhancement System # TGMRSB4S, that you would have to insert a spacer between the Timbren and the mount on your lifted 2002 Chevrolet Avalanche 2500 4x4.
The Spacer # A25723-90AH00 will allow you to acheive the correct geometry for your Avalanche. At this time we do not carry the correct hardware to go along with these so you will need to find bolts that are 1" longer than the included bolts in the kit. view full answer...
Yes, you can add the Dexter E-Z Flex along with the Correct Track # RR23QX. The only upgraded equalizer it won't work with is the MORryde CRE3000. Your 2020 Grand Design Imagine 2670MK currently has Dexter 7-3/4" equalizers so the correct kit is the # K71-655-00.
In addition to the equalizers I recommend the MORryde Suspension Upgrade Kit for Tandem Axle Trailers w Correct Track # MR58ZR. This is specifically designed to work with the Correct track and comes with wet bolts, bronze bushings,... view full answer...
Yes. The Trailer Idler Hub Assembly # AKIHUB-655-35-EZ-K is compatible with the Dexter Trailer Axle Beam with EZ Lube Spindles # T3584F-EZ-8974 because the hub uses a # L68149 inner bearing and a # L44649 outer bearing. These hubs come with lug nuts included and the axle comes with the spindle nuts included. If you need mounting bolts to mount your axle to the leaf springs, you can use the U-bolt Kit for Mounting 3500-lbs Axles # APUBR-1. view full answer...
The Curt 17022 is an older system that doesn't include the built-in grease zerk fittings found on the newer Curt # C17062 system. These systems are very similar in all other capacities.
When looking for the best weight distribution system for your trailer, you want to account for the loaded tongue weight of your trailer as well as any cargo weight behind the rear axle of your Avalanche. The tongue weight is typically 10-15% of the loaded tongue weight of your trailer.
It is very likely... view full answer...
Your 2010 Chevy Avalanche comes from the factory with a 2 inch trailer hitch. Since you have a 2 inch trailer hitch receiver opening, you will be able to use the Alabama Chrome Mascot Emblem Hitch Cover, # AMG100017, or any other hitch cover designed to fit a 2 inch receiver. You may also be interested in Trailer Hitch Receiver Lock, # e98880, to secure the hitch cover or other accessories and to deter theft. I have included a link to a video review of this lock below. view full answer...
The manufacturer DeeZee does not list the Tailgate Assist Custom Tailgate-Lowering System part # DZ43102 as a fit for a 2013 Chevrolet Avalanche LTZ. However, we have had two separate reviews which I have attached for you that state the product will work on an Avalanche. view full answer...
I can help you find the right replacement lock cylinder for your 2007 Chevy Avalanche LT Toolbox.
If your current lock cylinder can be removed from your Avalanche's toolbox then you will need the Late Model GM Key Cylinder from BOLT # BL692915. Usually, if the lock is going to be able to be replaced it will have a thin nut on the back of the cylinder on the interior of the toolbox that can be loosened and removed. I've included an image to show you what I'm talking about.
If you happen... view full answer...
Seems like you're looking to cool your engine oil. This Derale Engine cooler kit # D15450 is designed to fit GM vehicles. Mount it wherever you will get the most air flow. Whenever adding engine oil coolers, remember that you will increase the amount of oil you can carry. view full answer...
I do have an option for you but the 2010 Chevrolet Avalanche doesn't have a trailer brake controller plug under the dash. That said, there are wires for one so all you need to install the Tekonsha BRAKE-EVN Trailer Brake Controller part # TK63VR is the Tekonsha Pigtail Wiring Harness part # 7894. view full answer...
Yes you can absolutely use a Blue Ox Tow Bar like the Blue Ox Ascent Non-Binding Tow Bar - Motorhome Mount # BX4375 with your Roadmaster Direct-Connect Base Plate Kit, you will just need an adapter to adapt the tow bars to the base plate.
I took a look at what Roadmaster Base Plates are offered for your vehicle, and it appears you'll have either the:
- Roadmaster Direct-Connect Base Plate Kit - Removable Arms # 3154-3,
Or the,
-Roadmaster Crossbar-Style Base Plate Kit - Removable Arms... view full answer...
A radial tire is actually a better option than a bias tire; radial tires are going to flex more than bias tires and also run cooler, which means they are better for standard driving. A bias tire is going to be better for off-road, agricultural use so I highly recommend a radial tire for a camper.
In terms of your load range C tire with a rating of 1,820 lbs, that would mean when inflated to the max 50 psi the tires have a capacity of 7,280 lbs and you will want a capacity that is at least... view full answer...
The AirLift 1000 Air Helper Spring kit # AL60769 installs inside your rear coil springs. This type of air bag cannot be used with suspension lift spacers the way you can with a kit like the Firestone # F2250 that mounts to the axle.
If you have a 2WD without factory top overload springs you can easily install rear suspension kit # CSS-1125R from Super Springs. Because this installs inside the turns of the coil springs it needs no spacers. This kit is simple to install, cost effective and... view full answer...
Go To Results